Validation of Bed-Load Transport Measurements with Time-Sequenced Bathymetric Data
Publication: Journal of Hydraulic Engineering
Volume 137, Issue 7
Abstract
Advances in bathymetric data acquisition have made it possible to explore alternative methods for measuring bed-load transport in rivers. The method validated herein consists of measuring rates of bed scour by using time-sequenced bathymetric data. The validation is performed in a laboratory flume by comparing the measured rates of bed scour with direct measurements of bed-load transport. The bed forms in the flume are dunes traveling at nearly constant speed. The shape of the dunes remains nearly constant. No suspended load is present. The ranges for Froude and Rouse numbers are 0.24–0.50 and 4.6–10.4, respectively. The study shows that under the given conditions, bed-load transport determined from time-sequenced bathymetric data is equally accurate to that determined from measurements of bed-form amplitude and speed. Obtaining bed-load transport from time-sequenced bathymetric data is often more expedient than traditional methods.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research and data analysis presented herein were conducted under the sponsorship of the U.S. Army Corps of Engineers Engineer Research and Development Center (USACE-ERDC)USACE in cooperation with the Agricultural Research Service-National Sedimentation Laboratory (ARS-NSL) and the Iowa Institute of Hydraulic Research (IIHR) at the University of Iowa. Permission was granted by the Chief of Engineers to publish this information.
References
Abraham, D., Cowan, M., Hendrickson, J., Katzenmeyer, W., Landwehr, K., and Pratt, T. (2006). “Effects of pool drawdown and wing dams (Pool8), and closure dams (Pool 13), on navigation channel sedimentation processes, upper Mississippi River.” USACE-ERDC Technical Rep., TR-06-2.
Abraham, D., and Hendrickson, J. (2003). “Effects of drawdown and structures on bed-load transport in Pool 8 navigation channel.” USACE ERDC/CHL Technical Note, CHETN-VII-5.
Abraham, D., and Kuhnle, R. (2006). “Using high resolution bathymetric data for measuring bed-load transport.” presented at the Joint 8th Federal Interagency Sedimentation Conf. and 3rd Federal Interagency Hydrologic Modeling Conf., Reno, NV.
Abraham, D., and Pratt, T. (2002). “Quantification of bed-load transport on the upper Mississippi River using multibeam survey data and traditional methods.” USACE-ERDC/CHL Technical Note, CHETN-VII-4.
Abraham, D., Pratt, T., and Sharp, J. (2010). “Measuring bedload transport on the Missouri River using time sequenced bathymetric data.” 2nd Joint Federal Interagency Conf., Las Vegas, NV.
Bunte, K., and Abt, S. R. (2005). “Effect of sampling time on measured gravel bed load transport rates in a coarse-bedded stream.” Water Resour. Res., 41, W11405.
Carey, W. P. (1985). “Variability in measured bedload-transport rates. American Water Resources Association.” Water Resources Bulletin, 21(1), 39–48.
Crickmore, M. J. (1970). “Effect of flume width on bed-form characteristics.” J. Hydraul. Div., 96, 473–496.
Dinehart, R. L. (2002). “Bed form movement recorded by sequential single-beam surveys in tidal rivers.” J. Hydrol. (Amsterdam), 258, 25–39.
Engel, P., and Lam Lau, Y. (1980). “Computation of bed load using bathymetric data.” J. Hydraul. Div., 106, 369–380.
Exner, F. (1925). “Uber die Wechselwirkung swischen Wasser und Geschibe in Flussen.” Proc., Vienna Academy of Sciences, Section IIA, 134, 1925.
Gray, J. R., Webb, R. H., and Hyndman, D. W. (1991). “Low-flow sediment transport in the Colorado River.” 5th Federal Interagency Sedimentation Conf., Subcommittee on Sedimentation, Interagency Advisory Committee on Water Data, Las Vegas, NV, 4-63–-4-71.
Julien, P. Y., and Klaassen, G. J. (1995). “Sand-dune geometry of large rivers during floods.” J. Hydraul. Eng., 121, 657–663.
Kondap, D. M., and Garde, R. J. (1973). “Velocity of bed forms in alluvial channels.” Proc., 15th Congress of Int. Association for Hydraulic Research, 5, Istanbul, Turkey.
Kuhnle, R. A. (2008). “5.4 Bed load samplers.” Sedimentation engineering, processes, measurements, modeling, practice, ASCE manual no. 110, M. H. Garcia, ed., ASCE, Reston, VA.
Kuhnle, R., and Derrow, R. (1994). “Using the sedbed monitor to measure bed load.” Proc., Symp. on Fundamentals and Advancements in Hydraulic Measurements and Experimentation, Buffalo, NY.
Kuhnle, R. A., and Southard, J. B. (1988). “Bed load transport fluctuations in a gravel bed laboratory channel.” Water Resour. Res., 24(2), 247–260.
McElroy, B., and Mohrig, D. (2009). “Nature of deformation of sandy bed forms.” J. Geophys. Res., 114, F00A04.
Nittrouer, J. A., Allison, M. A., and Campanella, R. (2008). “Bedform transport rates for the lowermost Mississippi River.” J. Geophys. Res., 113(F03004).
Shields, F. D., Jr., Copeland, R. R., Klingeman, P. C., Doyle, M. W., and Simon, A. (2008). “9-Stream restoration.” Sedimentation engineering, processes, measurements, modeling, practice, ASCE manual no. 110, M. H. Garcia, ed., ASCE, Reston, VA.
Simons, D. B., Richardson, E. V., and Nordin, C. F., Jr. (1965). “Bedload equation for ripples and dunes.” U.S. Geological Survey Professional Paper 462-H.
Singh, A., et al. (2009). “Experimental evidence for statistical scaling and intermittency in sediment transport rates.” J. Geophys. Res., 114, F01025.
Wilbers, A. (2004). “The development and hydraulic roughness of subaqueous dunes.” Netherlands Geographical Studies 323, The Royal Dutch Geographical Society, Utrecht, Netherlands, 227.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Sep 30, 2009
Accepted: Oct 28, 2010
Published online: Jan 3, 2011
Published in print: Jul 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.