Effects of Cyclic Temperature Variations on Thermal Response of an Energy Pile under a Residential Building
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 145, Issue 10
Abstract
The effects of daily cyclic temperature variations on the thermal response of an energy pile built under a six-level residential building are examined. The axial and radial thermal strains along the length of the pile followed stable, linear reversible paths during daily active heating and cooling cycles corresponding to a pile temperature range of 10°C to 23°C ( of to 5°C) around a baseline temperature of 18°C. The stable responses of the thermal strains indicate that plastic deformations did not occur in the pile during the daily cyclic temperature changes coupled with the mechanical load in the pile corresponding to 52% of its estimated ultimate capacity. A complex distribution of axial thermal stresses with depth was observed in the pile, with higher stress magnitudes near the pile ends particularly at the end of cooling because of larger temperature changes in the cooling cycle. The magnitudes of radial thermal stresses were considerably smaller than the axial thermal stresses along the length of the pile and are not anticipated to play a significant role in the development of thermomechanical loads in the pile. The temperatures over the cross section of the pile were uniformly distributed at the end of cooling and heating at all depths, while the axial thermal stresses had a nonuniform distribution but with magnitudes less than the calculated ultimate capacity of the pile.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research project is supported by the Australian Research Council’s Linkage Projects funding scheme (Project No. LP120200613). The authors also acknowledge the Australian Government Research Training Program Scholarship provided to the first author. The US National Science Foundation (Grant No. CMMI-0928159) supported the third author. The support of all sponsors is gratefully acknowledged.
References
Abdelaziz, S., and T. Y. Ozudogru. 2016a. “Non-uniform thermal strains and stresses in energy piles.” Environ. Geotech. 3 (4): 237–252. https://doi.org/10.1680/jenge.15.00032.
Abdelaziz, S. L., and T. Y. Ozudogru. 2016b. “Selection of the design temperature change for energy piles.” Appl. Therm. Eng. 107 (Aug): 1036–1045. https://doi.org/10.1016/j.applthermaleng.2016.07.067.
Akrouch, G., M. Sánchez, and J-L. Briaud. 2014. “Thermo-mechanical behavior of energy piles in high plasticity clays.” Acta Geotech. 9 (3): 399–412. https://doi.org/10.1007/s11440-014-0312-5.
Amatya, B. L., K. Soga, P. J. Bourne-Webb, T. Amis, and L. Laloui. 2012. “Thermo-mechanical behaviour of energy piles.” Géotechnique 62 (6): 503–519. https://doi.org/10.1680/geot.10.P.116.
Amis, T., P. J. Bourne-Webb, C. Davidson, B. Amatya, and K. Soga. 2008. “The effects of heating and cooling energy piles under working load at Lambeth College, UK.” In Proc., 33rd Annual and 11th Int. Conf. New York: Deep Foundations Institute.
Barry-Macaulay, D. 2013. “An investigation on the thermal and thermo-mechanical behaviour of soils.” M.S. thesis, Dept. of Civil Engineering, Monash Univ.
Barry-Macaulay, D., A. Bouazza, R. M. Singh, and B. Wang. 2014. “Thermal properties of some Melbourne soils and rocks.” Aust. Geomech. J. 49 (2): 31–44.
Barry-Macaulay, D., A. Bouazza, R. M. Singh, B. Wang, and P. G. Ranjith. 2013. “Thermal conductivity of soils and rocks from the Melbourne (Australia) region.” Eng. Geol. 164 (Sep): 131–138. https://doi.org/10.1016/j.enggeo.2013.06.014.
Bouazza, A., R. M. Singh, and M. Faizal. 2015. “Full scale geothermal energy pile studies at Monash University, Melbourne, Australia.” In Thermoactive foundations for sustainable buildings, edited by J. S. McCartney, M. Krarti, B. C. Kwag, A. Bouazza, R. M. Singh, and M. Faizal, 95–117. New York: ASME.
Bourne-Webb, P. J., B. Amatya, and K. Soga. 2013. “A framework for understanding energy pile behaviour.” Proc. Inst. Civ. Eng. Geotech. Eng. 166 (2): 170–177. https://doi.org/10.1680/geng.10.00098.
Bourne-Webb, P. J., B. Amatya, K. Soga, T. Amis, C. Davidson, and P. Payne. 2009. “Energy pile test at Lambeth College, London: Geotechnical and thermodynamic aspects of pile response to heat cycles.” Géotechnique 59 (3): 237–248. https://doi.org/10.1680/geot.2009.59.3.237.
Brandl, H. 1998. “Energy piles and diaphragm walls for heat transfer from and into the ground.” In Proc., 3rd Int. Geotechcnial Seminar on Deep Foundations on Bored and Auger Piles, edited by W. F. Van Impe and W. Haegeman, 37–60. Rotterdam, Netherlands: A.A. Balkema.
Brandl, H. 2006. “Energy foundations and other thermo-active ground structures.” Géotechnique 56 (2): 81–122. https://doi.org/10.1680/geot.2006.56.2.81.
Caulk, R., E. Ghazanfari, and J. S. McCartney. 2016. “Parameterization of a calibrated geothermal energy pile model.” Geomech. Energy Environ. 5 (3): 1–15. https://doi.org/10.1016/j.gete.2015.11.001.
Chen, D., and J. S. McCartney. 2017. “Parameters for load transfer analysis of energy piles in uniform nonplastic soils.” Int. J. Geomech. 17 (7): 04016159. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000873.
Donna, A. D., A. Ferrari, and L. Laloui. 2016. “Experimental investigations of the soil-concrete interface: Physical mechanisms, cyclic mobilization, and behaviour at different temperatures.” Can. Geotech. J. 53 (4): 659–672. https://doi.org/10.1139/cgj-2015-0294.
Faizal, M. 2018. “Axial and radial thermal responses of field-scale energy piles.” Ph.D. thesis, Dept. of Civil Engineering, Monash Univ.
Faizal, M., A. Bouazza, C. Haberfield, and J. S. McCartney. 2018a. “Axial and radial thermal responses of a field-scale energy pile under monotonic and cyclic temperature changes.” J. Geotech. Geoenviron. Eng. 144 (10): 04018072. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001952.
Faizal, M., A. Bouazza, J. S. McCartney, and C. Haberfield. 2018b. “Axial and radial thermal responses of an energy pile under a 6-storey residential building.” Can. Geotech. J. 56 (7): 1019–1033. https://doi.org/10.1139/cgj-2018-0246.
Faizal, M., A. Bouazza, and R. M. Singh. 2016. “An experimental investigation of the influence of intermittent and continuous operating modes on the thermal behaviour of a full scale geothermal energy pile.” Geomech. Energy Environ. 8 (Dec): 8–29. https://doi.org/10.1016/j.gete.2016.08.001.
Gawecka, K. A., D. M. G. Taborda, D. M. Potts, W. Cui, L. Zdravković, and M. S. H. Kasri. 2017. “Numerical modelling of thermo-active piles in London Clay.” Proc. Inst. Civ. Eng. Geotech. Eng. 170 (3): 201–219. https://doi.org/10.1680/jgeen.16.00096.
Kalantidou, A., A. M. Tang, J-M. Pereira, and G. Hassen. 2012. “Preliminary study on the mechanical behaviour of heat exchanger pile in physical model.” Géotechnique 62 (11): 1047–1051. https://doi.org/10.1680/geot.11.T.013.
Knellwolf, C., H. Peron, and L. Laloui. 2011. “Geotechnical analysis of heat exchanger piles.” J. Geotech. Geoenviron. Eng. 130 (10): 890–902. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000513.
Laloui, L., M. Nuth, and L. Vulliet. 2006. “Experimental and numerical investigations of the behaviour of a heat exchanger pile.” Int. J. Numer. Anal. Methods Geomech. 30 (8): 763–781. https://doi.org/10.1002/nag.499.
McCartney, J. S., and K. D. Murphy. 2012. “Strain distributions in full-scale energy foundations.” DFI J.: J. Deep Found. Inst. 6 (2): 26–38. https://doi.org/10.1179/dfi.2012.008.
McCartney, J. S., and K. D. Murphy. 2017. “Investigation of potential dragdown/uplift effects on energy piles.” Geomech. Energy Environ. 10 (Jun): 21–28. https://doi.org/10.1016/j.gete.2017.03.001.
Mimouni, T. 2014. “Thermomechanical characterization of energy geostructures with emphasis on energy piles.” Ph.D. thesis, Laboratory of Soil Mechanics, École Polytechnique Fédérale de Lausanne.
Mimouni, T., and L. Laloui. 2015. “Behaviour of a group of energy piles.” Can. Geotech. J. 52 (12): 1913–1929. https://doi.org/10.1139/cgj-2014-0403.
Murphy, K. D., and J. S. McCartney. 2015. “Seasonal response of energy foundations during building operation.” Geotech. Geol. Eng. 33 (2): 343–356. https://doi.org/10.1007/s10706-014-9802-3.
Murphy, K. D., J. S. McCartney, and K. S. Henry. 2015. “Evaluation of thermo-mechanical and thermal behavior of full-scale energy foundations.” Acta Geotech. 10 (2): 179–195. https://doi.org/10.1007/s11440-013-0298-4.
Nguyen, V. T., A. M. Tang, and J.-M. Pereira. 2017. “Long-term thermo-mechanical behavior of energy pile in dry sand.” Acta Geotech. 12 (4): 729–737. https://doi.org/10.1007/s11440-017-0539-z.
Olgun, C. G., T. Y. Ozudogru, and C. F. Arson. 2014. “Thermo-mechanical radial expansion of heat exchanger piles and possible effects on contact pressures at pile-soil interface.” Géotech. Lett. 4 (3): 170–178. https://doi.org/10.1680/geolett.14.00018.
Ozudogru, T. Y., C. G. Olgun, and C. F. Arson. 2015. “Analysis of friction induced thermo-mechanical stresses on a heat exchanger pile in isothermal soil.” Geotech. Geol. Eng. 33 (2): 357–371. https://doi.org/10.1007/s10706-014-9821-0.
Pasten, C., and J. Santamarina. 2014. “Thermally induced long-term displacement of thermoactive piles.” J. Geotech. Geoenviron. Eng. 140 (5): 06014003. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001092.
Saggu, R., and T. Chakraborty. 2015. “Cyclic thermo-mechanical analysis of energy piles in sand.” Geotech. Geol. Eng. 33 (2): 321–342. https://doi.org/10.1007/s10706-014-9798-8.
Stewart, M. A., and J. S. McCartney. 2014. “Centrifuge modeling of soil-structure interaction in energy foundations.” J. Geotech. Geoenviron. Eng. 140 (4): 04013044. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001061.
Suryatriyastuti, M. E., H. Mroueh, and S. Burlon. 2013. “Numerical analysis of the bearing capacity in thermo-active piles under cyclic axial loading.” In Energy geostructures: Innovation in underground engineering, edited by L. Laloui and A. D. Donna, 139–154. Hoboken, NJ: Wiley.
Sutman, M., G. Olgun, L. Laloui, and T. Brettmann. 2017. “Effect of end-restraint conditions on energy pile behavior.” In Proc., Geotechnical Frontiers 2017, 165–174. Reston, VA: ASCE.
Wang, B. 2017. “Behaviour of pile foundations subjected to thermal loading.” M.S. thesis, Dept. of Civil Engineering, Monash Univ.
Wang, B., A. Bouazza, R. Singh, C. Haberfield, D. Barry-Macaulay, and S. Baycan. 2015. “Posttemperature effects on shaft capacity of a full-scale geothermal energy pile.” J. Geotech. Geoenviron. Eng. 141 (4): 04014125. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001266.
Wang, C. L., H. Liu, G. Kong, and C. W. W. Ng. 2017. “Different types of energy piles with heating-cooling cycles.” Geotech. Eng. 170 (3): 220–231. https://doi.org/10.1680/jgeen.16.00061.
Wood, C. J., H. Liu, and S. B. Riffat. 2010. “Comparison of a modelled and field tested piled ground heat exchanger system for a residential building and the simulated effect of assisted ground heat recharge.” Int. J. Low-Carbon Technol. 5 (3): 137–143. https://doi.org/10.1093/ijlct/ctq015.
Yavari, N., A. M. Tang, J. M. Pereira, and G. Hassen. 2014. “Experimental study on the mechanical behaviour of a heat exchanger pile using physical modelling.” Acta Geotech. 9 (3): 385–398. https://doi.org/10.1007/s11440-014-0310-7.
Yavari, N., A. M. Tang, J. M. Pereira, and G. Hassen. 2016a. “Effect of temperature on the shear strength of soils and the soil-structure interface.” Can. Geotech. J. 53 (7): 1186–1194. https://doi.org/10.1139/cgj-2015-0355.
Yavari, N., A. M. Tang, J. M. Pereira, and G. Hassen. 2016b. “Mechanical behaviour of a small-scale energy pile in saturated clay.” Géotechnique 66 (11): 878–887. https://doi.org/10.1680/jgeot.15.T.026.
Yi, M., Y. Hongxing, and F. Zhaohong. 2008. “Study on hybrid ground-coupled heat pump systems.” Energy Build. 40 (11): 2028–2036. https://doi.org/10.1016/j.enbuild.2008.05.010.
You, S., X. Cheng, H. Guo, and Z. Yao. 2016. “Experimental study on structural response of CFG energy piles.” Appl. Therm. Eng. 96 (Mar): 640–651. https://doi.org/10.1016/j.applthermaleng.2015.11.127.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 145 • Issue 10 • October 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jul 17, 2018
Accepted: May 16, 2019
Published online: Jul 22, 2019
Published in print: Oct 1, 2019
Discussion open until: Dec 22, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.