Inverse Analysis of a Supported Excavation in Chicago
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 145, Issue 9
Abstract
Adaptive management is a design approach which allows one to change support and/or construction procedures during excavation based on observed responses to meet specific design objectives. To obtain the most benefit from an adaptive management approach, inverse analysis procedures are used to make parameter updates based on observations collected during the early stages of a project and applied to later stages to predict future performance. This paper describes the inverse analysis of lateral wall deformation data collected from a supported excavation in Chicago. The Hardening Soil (HS) model and the HS model with small-strain stiffness are used to represent stress-strain behavior of medium clay and stiff clay layers of an excavation in Chicago. Initial parameters for the soil models are based on previous inverse analysis studies conducted for excavations in Chicago soils. Deformations computed using the initial parameters are compared with the field measurements to evaluate the capabilities and limitations of each model. Optimization during inverse analysis is based on a gradient method using measured lateral wall deformations. Changes in the optimized parameters during various levels of excavation are assessed. Computations made with the optimized soil parameters are compared and their efficacies for prediction purposes are evaluated.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The funding for the work reported herein was provided by a National Science Foundation grant CMMI-1603060. The support of Dr. Richard Fragaszy is greatly appreciated. Hayward Baker, Inc. was the excavation support subcontractor, and GETEC provided the website with real-time access to the SAA data. The authors thank Mr. Justin Lewis and Mr. Nathan Van Winkle of Hayward Baker for their efforts in collecting the field performance data.
References
Benz, T. 2007. “Small-strain stiffness of soils and its numerical consequences.” Ph.D. thesis, Institut fur Geotechnik, Universitat Stuttgart.
Blackburn, J. T., and R. J. Finno. 2007. “Three-dimensional responses observed in an internally braced excavation in soft clay.” J. Geotech. Geonenviron. Eng. 133 (11): 1364–1373. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:11(1364).
Calvello, M. 2002. “Inverse analysis of a supported excavation through Chicago glacial clays.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Northwestern Univ.
Calvello, M., and R. J. Finno. 2004. “Selecting parameters to optimize in model calibration by inverse analysis.” Comput. Geotech. 31 (5): 410–424. https://doi.org/10.1016/j.compgeo.2004.03.004.
Christian, J. T. 2004. “Geotechnical engineering reliability: How well do we know what we are doing?” J. Geotech. Geoenviron. Eng. 130 (10): 985–1003. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:10(985).
Finno, R. J. 2007. “Use of monitoring data to update performance predictions of supported excavations.” In 7th FMGM 2007: Field Measurements in Geomechanics, 1–30. Reston, VA: ASCE.
Finno, R. J. 2008. “Linking field observations and performance prediction updates during construction.” In Proc., 15th Great Lakes Geotechnical/Geoenvironmental Conf. Indianapolis, IN: ASCE.
Finno, R. J., S. Bryson, and M. Calvello. 2002. “Performance of stiff support system in soft clay.” J. Geotech. Geoenviron. Eng. 128 (8): 660–671. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:8(660).
Finno, R. J., and M. Calvello. 2005. “Supported excavations: Observational method and inverse modeling.” J. Geotech. Geoenviron. Eng. 131 (7): 826–836. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:7(826).
Finno, R. J., D. R. Hiltunen, and T. Kim. 2012. “Elastic cross-anisotropy of Chicago glacial clays from field and laboratory data.” In Proc., State of the Art and Practice in Geotechnical Engineering, GeoCongress 2012, 2609–2618. Reston, VA: ASCE.
Finno, R. J., S. Kim, J. Lewis, and N. Van Winkle. 2019. “Observed performance of a sheetpile-supported excavation in Chicago clays.” J. Geotech. Geoenviron. Eng. 145 (2): 05018005. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002010.
Finno, R. J., and T. Kim. 2012. “Effects of stress path rotation angle on small strain responses.” J. Geotech. Geoenviron. Eng. 138 (4): 526–534. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000612.
Finno, R. J., Z. Shi, S. Kim, N. Crafton, and D. Rendell. 2017. “Adaptive management evaluation of the SQBRC excavation.” In Proc., Workshop for Simulation of Construction Processes in Geotechnical Engineering FOR 1136 GEOTECH, 42–67. New York: Springer.
Hardin, B. O., and V. P. Drnevich. 1972. “Shear modulus and damping in soils: Design equations and curves.” J. Soil Mech. Found. Div. 98 (SM7): 667–692.
Hashash, Y. M. A., and R. J. Finno. 2008. “Development of new integrated tools for predicting, monitoring and controlling ground movements due to excavations.” Pract. Period. Struct. Des. Constr. 13 (1): 4–10. https://doi.org/10.1061/(ASCE)1084-0680(2008)13:1(4).
Hashash, Y. M. A., H. Song, and A. Osouli. 2011. “Three-dimensional inverse analyses of a deep excavation in Chicago clays.” Int. J. Numer. Anal. Methods Geomech. 35: 1059–1075. https://doi.org/10.1002/nag.949.
Hashash, Y. M. A., and A. J. Whittle. 1996. “Ground movement prediction for deep excavations in soft clay.” J. Geotech. Eng. 122 (6): 474–486. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:6(474).
Jung, Y. H., W. Cho, and R. J. Finno. 2007. “Defining yielding from bender element measurements in triaxial stress probe experiments.” J. Geotech. Geoenviron. Eng. 133 (7): 841–849. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:7(841).
Kim, S. 2018. “Observed performance and inverse analysis of a sheet pile-supported excavation in Chicago clays.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Northwestern Univ.
Ledesma, A., A. Gens, and E. E. Alonso. 1996. “Estimation of parameters in geotechnical backanalysis: Maximum likelihood approach.” Comput. Geotech. 18 (1): 1–27. https://doi.org/10.1016/0266-352X(95)00021-2.
Marquardt, D. W. 1963. “An algorithm for least-squares estimation of nonlinear parameters.” J. Soc. Ind. Appl. Math. 11 (2): 431–441. https://doi.org/10.1137/0111030.
Milioritsas, M. 2014. “Geotechnical modelling of a deep tunnel excavation in the boom clay formation.” MS thesis, Dept. of Civil Engineering, Delft Univ. of Technology.
Mu, L., R. J. Finno, M. Huang, T. Kim, and K. Kern. 2015. “Defining the soil parameters for computing deformations caused by braced excavation.” Maejo Int. J. Sci. Technol. 9 (2): 165–180.
Mu, L., and M. Huang. 2016. “Small strain based method for predicting three-dimensional soil displacements induced by braced excavation.” Tunnelling Underground Space Technol. 52 (Feb): 12–22. https://doi.org/10.1016/j.tust.2015.11.001.
Ou, C. Y., and Y. G. Tang. 1994. “Soil parameter determination for deep excavation analysis by optimization.” J. Chin. Inst. Eng. 17 (5): 671–688. https://doi.org/10.1080/02533839.1994.9677634.
Rechea, C. 2006. “Inverse analysis of excavations in urban environments.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Northwestern Univ.
Rechea, C., S. Levasseur, and R. J. Finno. 2008. “Inverse analysis techniques for parameter identification in simulation of excavation support systems.” Comput. Geotech. 35 (3): 331–345. https://doi.org/10.1016/j.compgeo.2007.08.008.
Schantz, T., P. A. Vermeer, and P. G. Bonnier. 1999. “The hardening soil model: Formulation and verification.” In Proc., Beyond 2000 in Computational Geotechnics, 291–290. Rotterdam, Netherlands: A.A. Balkelma.
Surarak, C., S. Likitlersuang, D. Wanatowski, A. Balasubramaniam, E. Oh, and H. Guan. 2012. “Stiffness and strength parameters for hardening soil model of soft and stiff Bangkok clays.” Soils Found. 52 (4): 682–697. https://doi.org/10.1016/j.sandf.2012.07.009.
Whitman, R. V. 2000. “Organizing and evaluating uncertainty in geotechnical engineering.” J. Geotech. Geoenviron. Eng. 126 (7): 583–593. https://doi.org/10.1061/(ASCE)1090-0241(2000)126:7(583).
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Dec 6, 2018
Accepted: Apr 4, 2019
Published online: Jul 3, 2019
Published in print: Sep 1, 2019
Discussion open until: Dec 3, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.