Estimation of Drained Shear Strength of Granular Soil from Shear Wave Velocity and Confining Stress
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 144, Issue 6
Abstract
Building upon a previously reported hypothesis suggesting a unique linear relationship between the small strain shear modulus and major principal effective stress at failure, this paper proposes a new empirical equation to estimate the drained shear strength from the measured shear wave velocity. A series of drained triaxial tests on clean sands and natural granular soils are performed to measure the shear strength of granular soils. Shear wave velocities are measured using bender elements installed at the top and bottom caps. Although a correlation between maximum shear modulus calculated from the shear wave velocity and effective stress at failure is observed, it is shown that the correlation can be further improved by including the confining stress. A unique relationship between maximum shear modulus, effective stress at failure, and confining stress is shown to exist for all granular soils tested. The predicted secant friction angles from the proposed empirical relationship exhibit good agreement with the measured values. The applicability of the equation is further validated through measured data on silty sand from a published study. Again, very favorable matches with the measured secant friction angles highlight the wide applicability of the proposed empirical relationship. A possible application of the proposed correlation is calculation of the shear strength from the shear wave velocity profile for strength correction in a seismic analysis.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Research Council of Science & Technology (NST) grant by the Korean government (MSIP) (No. CRC-16-02-KICT).
References
Andrus, R. D., and Stokoe, K. H. (2000). “Liquefaction resistance of soils from shear-wave velocity.” J. Geotech. Geoenviron. Eng., 1015–1025.
ASTM. (2005). “Standard specification for standard sand.” ASTM C778, West Conshohocken, PA.
Barreto, D., and O’sullivan, C. (2012). “The influence of inter-particle friction and the intermediate stress ratio on soil response under generalised stress conditions.” Granular Matter., 14(4), 505–521.
Cha, M., and Cho, G.-C. (2007). “Shear strength estimation of sandy soils using shear wave velocity.” ASTM Geotech. Test. J., 30(6), 484–495.
Ciang, Y. C., and Chae, Y. S. (1972). “Dynamic properties of cement treated soils.”, Highway Research Record, Washington, DC, 39–51.
Cresswell, A., Barton, M. E., and Brown, R. (1999). “Determining the maximum density of sands by pluviation.” ASTM Geotech. Test. J., 22(4), 324–328.
Dyvik, R., and Madshus, C. (1985). “Laboratory measurements of using bender elements.” Advances in the Art of Testing Soils under Cyclic Conditions, ASCE, New York, 186–196.
Fernandez, A. L. (2000). “Tomographic imaging the state of stress.” Ph.D. thesis, Georgia Institute of Technology, Atlanta.
Frost, J., and Park, J.-Y. (2003). “A critical assessment of the moist tamping technique.” ASTM Geotech. Test. J., 26(1), 57–70.
Gingery, J. R., and Elgamal, A. (2013). “Shear stress-strain curves based on the logic: A procedure for strength compatibility.” IACGE 2013, ASCE, Reston, VA, 721–729.
Green, R. A., et al. (2017). “Relative efficacy of CPT-versus Vs-based simplified liquefaction evaluation procedures.” 19th ICSMGE, KGS, Seoul, 1521–1524.
Groholski, D. R., Hashash, Y. M. A., Kim, B., Musgrove, M., Harmon, J., and Stewart, J. P. (2016). “Simplified model for small-strain nonlinearity and strength in 1D seismic site response analysis.” J. Geotech. Geoenviron. Eng., 04016042.
Guadalupe, Y., Baxter, C. D., and Sharma, M. S. R. (2013). “Measuring shear wave velocity in laboratory to link small- and large-strain behavior of soils.” Transp. Res. Rec., 2335, 79–88.
Hardin, B. O., and Drnevich, V. P. (1972). “Shear modulus and damping in soils: Design equations and curves.” J. Soil Mech. Found. Div., 98(SM7), 667–692.
Hardin, B. O., and Richart, F. E. (1963). “Elastic wave velocities in granular soils.” J. Soil Mech. Found. Div., 89(1), 33–66.
Hashash, Y. M., and Park, D. (2001). “Non-linear one-dimensional seismic ground motion propagation in the Mississippi embayment.” Eng. Geol., 62(1), 185–206.
Kayen, R., et al. (2013). “Shear-wave velocity-based probabilistic and deterministic assessment of seismic soil liquefaction potential.” J. Geotech. Geoenviron. Eng., 407–419.
Kokusho, T. (1980). “Cyclic triaxial test of dynamic soil properties for wide strain range.” Soils Found., 20(2), 45–60.
Ladd, R. (1974). “Specimen preparation and liquefaction of sands.” J. Geotech. Eng. Div., 100(10), 1180–1184.
Ladd, R. (1978). “Preparing test specimens using undercompaction.” ASTM Geotech. Test. J., 1(1), 16–23.
Lee, J.-S., and Santamarina, J. C. (2005). “Bender elements: Performance and signal interpretation.” J. Geotech. Geoenviron. Eng., 1063–1070.
Lee, J. S., and Yoon, H. K. (2014). “Porosity estimation based on seismic wave velocity at shallow depths.” J. Appl. Geophys., 105, 185–190.
Montoya, B. M., et al. (2012). “Fabrication, operation, and health monitoring of bender elements for aggressive environments.” ASTM Geotech. Test. J., 35(5), 728–742.
Park, D., and Kim, J. M. (2012). “Analysis of round robin test on seismic site response analysis.” KSCE J. Civ. Eng., 16(7), 1–10.
Robertson, P., Sasitharan, S., Cunning, J., and Sego, D. (1995). “Shear-wave velocity to evaluate in-situ state of Ottawa sand.” J. Geotech. Eng., 262–273.
Roesler, S. K. (1979). “Anisotropic shear modulus due to stress anisotropy.” J. Geotech. Eng. Div., 105(7), 871–880.
Salgado, R., Bandini, P., and Karim, A. (2000). “Shear strength and stiffness of silty sand.” J. Geotech. Geoenviron. Eng., 451–462.
Santamarina, J. C., Klein, K., and Fam, M. (2001). Soils and waves: Particulate materials behavior, characterization and process monitoring, Wiley, New York.
Saxena, S. K., Avramidis, A. S., and Reddy, K. R. (1988). “Dynamic moduli and damping ratios for cemented sands at low strains.” Can. Geotech. J., 25(2), 353–368.
Sharma, R., Baxter, C., and Jander, M. (2011). “Relationship between shear wave velocity and stresses at failure for weakly cemented sands during drained triaxial compression.” Soils Found., 51(4), 761–771.
Shi, J., and Asimaki, D. (2017). “From stiffness to strength: Formulation and validation of a hybrid hyperbolic nonlinear soil model for site-response analyses.” Bull. Seismol. Soc. Am., 107(3), 1336–1355.
Vaid, Y., and Negussey, D. (1988). “Preparation of reconstituted sand specimens.” ASTM STP977, ASTM, West Conshohocken, PA, 405–417.
Viggiani, G., and Atkinson, J. (1995). “Interpretation of bender element tests.” Geotechnique, 45(1), 149–154.
Yang, J., and Liu, X. (2016). “Shear wave velocity and stiffness of sand: The role of non-plastic fines.” Géotechnique, 66(6), 500–514.
Yee, E., Stewart, J. P., and Tokimatsu, K. (2013). “Elastic and large-strain nonlinear seismic site response from analysis of vertical array recordings.” J. Geotech. Geoenviron. Eng., 1789–1801.
Yimsiri, S., and Soga, K. (2010). “DEM analysis of soil fabric effects on behaviour of sand.” Géotechnique, 60(6), 483–495.
Yimsiri, S., and Soga, K. (2011). “Effects of soil fabric on behaviors of granular soils: Microscopic modeling.” Comput. Geotech., 38(7), 861–874.
Yoon, H.-K., and Lee, J.-S. (2010). “Field velocity resistivity probe for estimating stiffness and void ratio.” Soil Dyn. Earthquake Eng., 30(12), 1540–1549.
Yun, T. S., and Santamarina, J. C. (2005). “Decementation, softening, and collapse: Changes in small-strain shear stiffness in loading.” J. Geotech. Geoenviron. Eng., 350–358.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Nov 21, 2016
Accepted: Nov 9, 2017
Published online: Mar 27, 2018
Published in print: Jun 1, 2018
Discussion open until: Aug 27, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.