Hydraulic Performance of GCL Seams without Field-Applied Supplemental Bentonite below a Geomembrane Wrinkle
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 143, Issue 9
Abstract
The hydraulic performance of geosynthetic clay liner (GCL) overlapped seams relying on hydration of panel bentonite through a melted groove in one of its geotextiles to seal the overlap is reported for the situation where the seam is below a wrinkle in an overlying geomembrane. The amount of hydrated bentonite extruded through the groove at the seam depended on whether or not the groove melt was continuous. Flow along a seam having complete groove melt with well-hydrated bentonite was 2–3 times higher than that through a single panel of GCL below a wrinkle, but two orders of magnitude lower than that through a seam with incomplete groove melt. The effect of heat tacking on the hydraulic performance of an overlapped seam is examined. The method of heat tacking, the width of the heat-tacked zone, and its positioning at the seam were found to impact seam flow.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded by CETCO (Minerals Technologies, Inc.).
References
Ashe, L., Rowe, R., Brachman, R., and Take, W. (2015). “Laboratory study of downslope erosion for 10 different GCLs.” J. Geotech. Geoenviron. Eng., 04014079.
ASTM. (2006). “Standard test method for swell index of clay mineral component of geosynthetic clay liners.” ASTM D5890, West Conshohocken, PA.
ASTM. (2009). “Standard test methods for particle-size distribution (gradation) of soils using sieve analysis.” ASTM D6913, West Conshohocken, PA.
Barroso, M. C. P., Lopes, M. G. D. A., and Bergamini, G. (2010). “Effect of the waste pressure on fluid migration through geomembrane defects.” Proc. 9th Int. Conf. on Geosynthetics, International Geosynthetics Society, Jupiter, FL, 959–962.
Benson, C. H., Jo, H. Y., and Abichou, T. (2004). “Forensic analysis of excessive leakage from lagoons lined with a composite GCL.” Geosynth. Int., 11(3), 242–252.
Brachman, R. W. I., and Gudina, S. (2002). “A new laboratory apparatus for testing geomembranes under large earth pressures.” Proc., 55th Canadian Geotechnical Conf., Canadian Geotechnical Society, Richmond, BC, Canada, 993–1000.
Brachman, R. W. I., and Gudina, S. (2008). “Geomembrane strains from coarse gravel and wrinkles in a GM/GCL composite liner.” Geotext. Geomembr., 26(6), 488–497.
Brachman, R. W. I., Joshi, P., and Rowe, R. K. (2016). “Hydraulic performance of overlapped geosynthetic clay liner seams requiring field-applied supplemental bentonite.” J. Geotech. Geoenviron. Eng., 04016067.
Brachman, R. W. I., Joshi, P., Rowe, R. K., and Gudina, S. (2011). “Physical response of geomembrane wrinkles near GCL overlaps.” Proc., Geo-Frontiers 2011: Advances in Geotechnical Engineering, J. Han and D. E. Alzamora, eds., ASCE, Reston, VA.
CETCO. (2014). “BENTOMAT.”, Hoffman Estates, IL.
Cooley, B. H., and Daniel, D. E. (1995). “Seam performance of overlapped geosynthetic clay liners.” Proc., Geosynthetics 1995, IFAI, St. Paul, MN, 691–705.
Daniel, D. E., Trautwein, S. J., and Goswami, P. (1997). “Measurement of hydraulic properties of GCLs using a flow box.” Testing and acceptance criteria for geosynthetic clay liners, L. W. Well, ed., ASTM, West Conshohocken, PA, 196–207.
Estornell, P., and Daniel, D. E. (1992). “Hydraulic conductivity of three geosynthetic clay liners.” J. Geotech. Eng., 1592–1606.
Gudina, S., and Brachman, R. W. I. (2006). “Effect of boundary conditions on deflection of GM wrinkles in a GM/GCL composite liner.” Proc. 8th Int. Conf. on Geosynthetics, International Geosynthetics Society, Jupiter, FL, 255–258.
Joshi, P., Brachman, R. W. I., and Rowe, R. K. (2011). “Heat-tacked overlap strength of four GCLs.” Proc., 14th Pan-American Conf. on Soil Mechanics and Geotechnical Engineering, Canadian Geotechnical Society, Richmond, BC, Canada.
Rowe, R. K. (2005). “Long-term performance of contaminant barrier systems.” Geotechnique, 55(9), 631–678.
Rowe, R. K. (2012). “Short and long-term leakage through composite liners.” Can. Geotech. J., 49(2), 141–169.
Rowe, R. K., and Abdelatty, K. (2012). “Effect of a calcium-rich soil on the performance of an overlying GCL.” J. Geotech. Geoenviron. Eng., 423–431.
Rowe, R. K., Bostwick, L. E., and Thiel, R. (2010). “Shrinkage characteristics of heat-tacked GCL seams.” Geotext. Geomembr., 28(4), 352–359.
Rowe, R. K., Chappel, M. J., Brachman, R. W. I., and Take, W. A. (2012). “Field study of wrinkles in a geomembrane at a composite liner test site.” Can. Geotech. J., 49(10), 1196–1211.
Rowe, R. K., Quigley, R. M., Brachman, R. W. I., and Booker, J. R. (2004). Barrier systems for waste disposal facilities, Taylor & Francis (E & FN Spon), London, 587.
SEEP/W 8.0.10.6504 [Computer software]. Calgary, AB, Canada, Geo-Slope.
Soong, T.-Y., and Koerner, R. M. (1998). “Laboratory study of high density polyethylene geomembrane waves.” Proc., Int. Conf. on Geosynthetics, Vol. 1, Industrial Fabrics Association International, St. Paul, MN, 301–306.
Thiel, R., and Thiel, C. (2009). “GCL shrinkage: A possible solution.” Geosynthetics Magazine, Feb./Mar. 2009, IFAI, St Paul, MN, 10–21.
Tognon, A. R., Rowe, R. K., and Brachman, R. W. I. (1999). “Evaluation of side wall friction for a buried pipe testing facility.” Geotext. Geomembr., 17(4), 193–212.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Oct 14, 2016
Accepted: Mar 27, 2017
Published online: Jun 30, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 30, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.