Technical Papers
May 29, 2017

Long-Term Column Testing of Zeolite-Amended Backfills. I: Testing Methodology and Chemical Compatibility

Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 143, Issue 9

Abstract

Eight column tests were performed with specimens comprising unamended and zeolite-amended sand-bentonite backfills for vertical cutoff walls permeated with solutions of either 35 mM KCl (five tests) or 20 mM ZnCl2 (three tests) to evaluate the potential use of zeolite amendments for enhancing the sorption capacity of K+ and Zn2+. The column tests used flow-pump systems to maintain constant flow rates and flexible-wall cells to minimize the potential for side-wall leakage and short circuiting of solutes. However, the use of low flow rates (2.068.05  mL/d) to prevent membrane blow-out and initial permeation with deionized water to control soluble salts contributed to extensive test durations ranging from 385 days (1.05 year) to 1,370 days (3.75 year). The column specimens were characterized by soil:solution ratios ranging from 3.31 to 3.71 and hydraulic conductivity, k, based on permeation with a salt solution that were <1.0×109  m/s. Thus, the k of the backfill specimens was consistent with that typically required of backfills for vertical cutoff walls used for containment of contaminated groundwater. Also, effluent electrical conductivity (EC) and pH attained the values for the influent in the case of the 35 mM KCl solution, whereas for the low pH (1.83), 20 mM ZnCl2 solution, the buffering capacity of the backfill specimens reduced the contribution of H+ to the EC of the effluent, resulting in a slight increase in the effluent pH (2.80pH3.74). Finally, delayed breakthrough of K+ and Zn2+ was consistent with preferential cation exchange of K+ and Zn2+ relative to exchangeable Na+ and/or Ca2+ initially bound to the exchange sites of the bentonite and zeolite components of the backfills.

Get full access to this article

View all available purchase options and get full access to this article.

Acknowledgments

Financial support for this work was provided by the National Science Foundation (NSF) through Grant No. 0624104. The opinions and recommendations provided in this paper are solely those of the authors and are not necessarily consistent with the policies of NSF.

References

ASTM. (2004). “Standard test methods for measurement of hydraulic conductivity of saturated porous materials using a flexible wall permeameter.” ASTM D5084-03, West Conshohocken, PA.
ASTM. (2011). “Standard test method for hydraulic conductivity compatibility testing of soils with aqueous solutions.” ASTM D7100-11, West Conshohocken, PA.
Bierck, B. R., and Chang, W. C. (1994). “Contaminant transport through soil-bentonite slurry walls: Attenuation by activated carbon.” Proc., Specialty Conf. on Innovative Solutions for Contaminated Site Management, Water Environment Federation, Alexandria, VA, 461–472.
Bohnhoff, G., Shackelford, C. D., and Sample-Lord, K. (2014). “Calcium-resistant membrane behavior of polymerized bentonite.” J. Geotech. Geoenviron. Eng., 04013029.
Bradl, H. B. (1997). “Vertical barriers with increased sorption capacities.” 1997 Int. Containment Technology Conf., National Technical Information Service, Springfield, VA, 645–651.
Colombani, N., Mastrocicco, M., Di Giuseppe, D., Faccini, B., and Coltorti, M. (2015). “Batch and column experiments on nutrient leaching in soils amended with Italian natural zeolitites.” CATENA, 127(0), 64–71.
Daniel, D. E. (1994). “State-of-the-art: Laboratory hydraulic conductivity tests for saturated soils.” Hydraulic conductivity and waste contaminant transport in soil, D. E. Daniel and S. J. Trautwein, eds., ASTM, West Conshohoken, PA, 30–78.
Daniel, D. E., Anderson, D. C., and Boynton, S. S. (1985). “Fixed-wall versus flexible-wall permeameters.” Hydraulic barriers in soil and rock, A. I. Johnson, R. K. Frobel, N. J. Cavalli, and C. B. Pettersson, eds., ASTM, Philadelphia, 107–126.
Daniel, D. E., and Koerner, R. M. (1993). “Quality assurance and quality control for waste containment facilities.”, U.S. Environmental Protection Agency, Cincinnati.
Du, Y. J., Fan, R. D., Liu, S. Y., Reddy, K. R., and Jin, F. (2015). “Workability, compressibility and hydraulic conductivity of zeolite-amended clayey soil/calcium-bentonite backfills for slurry-trench cutoff walls.” Eng. Geol., 195(0), 258–268.
Evans, J. C., Adams, T. L., and Prince, M. J. (1997). “Metals attenuation in minerally-enhanced slurry walls.” 1997 Int. Containment Technology Conf., National Technical Information Service, Springfield, VA, 679–687.
Evans, J. C., Costa, M. J., and Cooley, B. (1995). “The state-of-stress in soil-bentonite slurry trench cutoff walls.” Geoenvironment 2000, Y. B. Acar and D. E. Daniel, eds., ASCE, Reston, VA, 1173–1191.
Evans, J. C., and Prince, M. J. (1997). “Additive effectiveness in minerally-enhanced slurry walls.” In situ remediation of the geoenvironment, J. C. Evans, ed., ASCE, Reston, VA, 181–196.
Fan, R. D., Du, Y. J., Reddy, K. R., Liu, S. Y., and Yang, Y. L. (2014). “Compressibility and hydraulic conductivity of clayey soil mixed with calcium bentonite for slurry wall backfill: Initial assessment.” Appl. Clay Sci., 101(0), 119–127.
Fernandez, F., and Quigley, R. M. (1991). “Controlling the destructive effects of clay-organic liquid interactions by application of effective stresses.” Can. Geotech. J., 28(3), 388–398.
Filz, G. M. (1996). “Consolidation stresses in soil-bentonite backfilled trenches.” Proc., 2nd Int. Congress on Environmental Geotechnics, A. A. Balkema, Rotterdam, Netherlands, 497–502.
Griffin, B., and Jurinak, J. (1973). “Estimation of activity coefficients from the electrical conductivity of natural aquatic systems and soil extracts.” Soil Sci., 116(1), 26–30.
Hong, C. S. (2016). “Zeolite-amended backfills for enhanced metals containment via soil-bentonite vertical cutoff walls.” Ph.D. dissertation, Colorado State Univ., Fort Collins, CO.
Hong, C. S., and Shackelford, C. D. (2017). “Long-term column testing of zeolite-amended backfills. II: Solute transport properties.” J. Geotech. Geoenviron. Eng., 04017051.
Hong, C. S., Shackelford, C. D., and Malusis, M. A. (2012). “Consolidation and hydraulic conductivity of zeolite-amended soil-bentonite backfills.” J. Geotech. Geoenviron. Eng., 15–25.
Hong, C. S., Shackelford, C. D., and Malusis, M. A. (2016). “Adsorptive behavior of zeolite-amended backfills for enhanced metals containment.” J. Geotech. Geoenviron. Eng., 04016021.
Hudak, P. F. (2016). “Evaluation of non-pumped wells with slurry cutoff walls for containing and removing contaminated groundwater.” Environ. Earth Sci., 75(1), 1–5.
Jo, H.-Y., Benson, C. H., Shackelford, C. D., Lee, J.-M., and Edil, T. B. (2005). “Long-term hydraulic conductivity of a geosynthetic clay liner (GCL) permeated with inorganic salt solutions.” J. Geotech. Geoenviron. Eng., 405–417.
LabVIEW [Computer software]. National Instruments, Austin, TX.
LaGrega, M. L., Buckingham, P. L., and Evans, J. C. (2001). Hazardous waste management, McGraw-Hill, New York.
Lee, J. M., and Shackelford, C. D. (2005). “Concentration dependency of the prehydration effect for a geosynthetic clay liner.” Soils Found., 45(4), 27–41.
Li, Y.-C., Cleall, P. J., Wen, Y.-D., Chen, Y.-M., and Pan, Q. (2015). “Stresses in soil-bentonite slurry trench cut-off walls.” Geotechnique, 65(10), 843–850.
Malusis, M. A., Barben, E. J., and Evans, J. C. (2009). “Hydraulic conductivity and compressibility of soil-bentonite backfill amended with activated carbon.” J. Geotech. Geoenviron. Eng., 664–672.
Malusis, M. A., Maneval, J. E., Barben, E. J., Shackelford, C. D., and Daniels, E. R. (2010). “Influence of adsorption on phenol transport through soil-bentonite vertical barriers amended with activated carbon.” J. Contam. Hydrol., 116(1–4), 58–72.
Malusis, M. A., and McKeehan, M. D. (2013). “Chemical compatibility of model soil-bentonite backfill containing multiswellable bentonite.” J. Geotech. Geoenviron. Eng., 189–198.
Manassero, M., Pasqualini, E., and Sani, D. (1998). “Potassium sorption isotherms of natural clayey-silt for pollutant containment.” 3rd Int. Congress on Environmental Geotechnics, P. Seco e Pinto, ed., Vol. 1, A. A. Balkema, Rotterdam, Netherlands, 235–240.
Mitchell, J. K., et al. (2007). Assessment of the performance of engineered waste containment barriers, National Academies Press, Washington, DC.
Mott, H. V., and Weber, W. J. (1992). “Sorption of low molecular weight organic contaminants by fly ash: Considerations for the enhancement of cutoff barrier performance.” Environ. Sci. Technol., 26(6), 1234–1242.
Park, J. K., Kim, J. Y., Madsen, C. D., and Edil, T. B. (1997). “Retardation of volatile organic compound movement by a soil-bentonite slurry cutoff wall amended with ground tires.” Water Environ. Res., 69(5), 1022–1031.
Rabideau, A., Shen, P., and Khandelwal, A. (1999). “Feasibility of amending slurry walls with zero-valent iron.” J. Geotech. Geoenviron. Eng., 330–333.
Redmond, P. L., and Shackelford, C. D. (1994). “Design and evaluation of a flow pump system for column testing.” Geotech. Test. J., 17(3), 269–281.
Reynolds, W. D., Gillham, R. W., and Cherry, J. A. (1982). “Evaluation of distribution coefficients for the prediction of strontium and cesium migration in a uniform sand.” Can. Geotech. J., 19(1), 92–103.
Rumer, R. R., and Mitchell, J. K. (1995). Assessment of barrier containment technologies: A comprehensive treatment for environmental remediation applications, National Technical Information Service, Springfield, VA.
Rumer, R. R., and Ryan, M. E. (1995). Barrier containment technologies for environmental remediation applications, Wiley, New York.
Ryan, C. R. (1984). “Slurry cutoff walls: Applications in the control of hazardous wastes.” Hydraulic barriers in soil and rock, A. I. Johnson, R. K. Frobel, N. J. Cavalli, and C. B. Pettersson, eds., ASTM, West Conshohoken, PA, 9–23.
Ryan, C. R. (1987). “Vertical barriers in soil for pollution containment.” Geotechnical practice for waste disposal ‘87, R. D. Woods, ed., ASCE, Reston, VA, 182–204.
Saria, L., Shimaoka, T., and Miyawaki, K. (2006). “Leaching of heavy metals in acid mine drainage.” Waste Manage. Res., 24(2), 134–140.
Shackelford, C. D. (1995a). “Analytical models for cumulative mass column testing.” Geoenvironment 2000, Y. B. Acar and D. E. Daniel, eds., ASCE, Reston, VA, 355–372.
Shackelford, C. D. (1995b). “Cumulative mass approach for column testing.” J. Geotech. Eng., 696–703.
Shackelford, C. D. (1994a). “Critical concepts for column testing.” J. Geotech. Eng., 1804–1828.
Shackelford, C. D. (1994b). “Waste-soil interactions that alter hydraulic conductivity.” Hydraulic conductivity and waste contaminant transport in soil, D. E. Daniel and S. J. Trautwein, eds., ASTM, Philadelphia, 111–168.
Shackelford, C. D., Benson, C. H., Katsumi, T., Edil, T. B., and Lin, L. (2000). “Evaluating the hydraulic conductivity of GCLs permeated with non-standard liquids.” Geotext. Geomembr., 18(2–4), 133–161.
Shackelford, C. D., and Jefferis, S. A. (2000). “Geoenvironmental engineering for in situ remediation.” Proc., Int. Conf. on Geotechnical and Geoenvironmental Engineering, Vol. 1, Technomic, Lancaster, PA, 121–185.
Shackelford, C. D., Malusis, M. A., Majeski, M. J., and Stern, R. T. (1999). “Electrical conductivity breakthrough curves.” J. Geotech. Geoenviron. Eng., 260–270.
Shackelford, C. D., and Redmond, P. L. (1995). “Solute breakthrough curves for processed kaolin at low flow rates.” J. Geotech. Eng., 17–32.
Sparks, D. L. (2003). Environmental soil chemistry, Academic, London.
Spooner, P. A., Wetzel, R. S., Spooner, C. E., Furman, C. A., Tokarski, E. F., and Hunt, G. E. (1984). “Slurry trench construction for pollution migration control.”, U.S. Environmental Protection Agency, Cincinnati.
Stern, R. A., and Shackelford, C. D. (1998). “Permeation of compacted sand-bentonite mixtures with calcium chloride solutions.” J. Geotech. Geoenviron. Eng., 231–241.
Tong, S., and Shackelford, C. D. (2016). “Standardized hydraulic conductivity of compacted sand-bentonite mixtures.” Geoetech. Test. J., 39(6), 1–15.

Information & Authors

Information

Published In

Go to Journal of Geotechnical and Geoenvironmental Engineering
Journal of Geotechnical and Geoenvironmental Engineering
Volume 143Issue 9September 2017

History

Received: Aug 30, 2016
Accepted: Feb 23, 2017
Published online: May 29, 2017
Published in print: Sep 1, 2017
Discussion open until: Oct 29, 2017

Permissions

Request permissions for this article.

Authors

Affiliations

Catherine S. Hong, Ph.D., A.M.ASCE [email protected]
Faculty Affiliate, Dept. of Civil and Environmental Engineering, 1372 Campus Delivery, Colorado State Univ., Fort Collins, CO 80523-1372. E-mail: [email protected]
Charles D. Shackelford, Ph.D., F.ASCE [email protected]
P.E.
Professor and Head, Dept. of Civil and Environmental Engineering, 1372 Campus Delivery, Colorado State Univ., Fort Collins, CO 80523-1372 (corresponding author). E-mail: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

Cited by

View Options

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share