A Release-to-Rest Model for Dynamically Installed Anchors
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 143, Issue 9
Abstract
Dynamically installed anchors are torpedo-shaped anchors that are installed by dropping them through the ocean such that they self-bury in the soft seabeds typically encountered in deep water. This paper presents and considers field data from reduced scale anchor tests at two sites to validate a new release-to-rest model for dynamically installed anchors. This model extends existing studies by considering the motion of the anchor from the point of release in the water column, modeling the drag resistance that acts on the anchor and its mooring line. Simulations from the model, together with data from the field tests, demonstrate the importance of considering the free-fall in water phase of installation, because the drag developed on the mooring line can be significant for larger release heights, reducing the anchor velocity as it arrives at the seabed by up to 44%. The soil embedment phase of the model also considers drag resistance on the anchor—and optionally on the mooring line—and accounts for the effect of the high anchor velocities on soil strength using a simple power law. Model simulations are shown in the paper to be in very good agreement with the anchor motion data measured in the field tests, resulting in predicted anchor embedments that are in agreement with the field database of over 100 anchor installations to an accuracy of .
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work forms part of the activities of the Centre for Offshore Foundation Systems (COFS), currently supported as a node of the Australian Research Council Centre of Excellence for Geotechnical Science and Engineering and as a Centre of Excellence by the Lloyd’s Register Foundation. The Lloyd’s Register Foundation invests in science, engineering, and technology for public benefit, worldwide. The authors are grateful to Waterways Ireland for allowing the work described here to take place in Lower Lough Erne.
References
Abelev, A., and Valent, P. (2009). “Strain-rate dependency of strength and viscosity of soft marine deposits of the Gulf of Mexico.” Proc., OCEANS 2009: Marine Technology for Our Future: Global and Local Challenges, Marine Technology Society Institute of Electrical and Electronic Engineers, Biloxi, MS, 1–9.
Andersen, K. H., et al. (2005). “Suction anchors for deepwater applications.” Proc., 1st Int. Symp. on Frontiers in Geotechnics, Taylor & Francis/A.A. Balkema, Leiden, Netherlands, 3–30.
API (American Petroleum Institute). (2002). “Recommended practice for planning, designing and constructing fixed offshore platforms—Working stress design.” API RP 2A-WSD, Washington, DC.
Aubeny, C., and Shi, H. (2006). “Interpretation of impact penetration measurements in soft clays.” J. Geotech. Geoenviron. Eng., 770–777.
Beard, R. M. (1981). “A penetrometer for deep ocean seafloor exploration.” Proc., OCEANS 1981: The Ocean an Int. Workplace, MTS/IEEE, Boston, 668–673.
Biscontin, G., and Pestana, J. M. (2001). “Influence of peripheral velocity on vane shear strength of an artificial clay.” Geotech. Testing J., 24(4), 423–429.
Blake, A. P., and O’Loughlin, C. D. (2015). “Installation of dynamically embedded plate anchors as assessed through field tests.” Can. Geotech. J., 52(9), 1270–1282.
Blake, A. P., O’Loughlin, C. D., and Gaudin, C. (2015). “Capacity of dynamically embedded plate anchors as assessed through field tests.” Can. Geotech. J., 52(1), 87–95.
Blake, A. P., O’Loughlin, C. D., Morton, J. M., O’Beirne, C., Gaudin, C., and White, D. J. (2016). “In situ measurement of the dynamic penetration of free-fall projectiles in soft soils using a low cost inertial measurement unit.” Geotech. Test. J., 39(2), 235–251.
By, T., and Skomedal, E. (1992). “Soil parameters for foundation design, Troll platform.” Proc., Int. Conf. on Behaviour of Offshore Structures (Boss), Imperial College London, London.
Casagrande, A., and Wilson, S. (1951). “Effect of rate of loading on the strength of clays and shales at constant water content.” Géotechnique, 2(3), 251–263.
Chow, S. H., O’Loughlin, C. D., and Randolph, M. F. (2014). “Soil strength estimation and pore pressure dissipation for free-fall piezocone in soft clay.” Géotechnique, 64(10), 817–827.
Chow, S. H., O’Loughlin, C. D., White, D. J., and Randolph, M. F. (2017). “An extended interpretation of the free-fall piezocone test in clay.” Géotechnique, 1–14.
Chung, S. F., Randolph, M. F., and Schneider, J. A. (2006). “Effect of penetration rate on penetrometer resistance in clay.” J. Geotech. Geoenviron. Eng., 1188–1196.
Colreavy, C., O’Loughlin, C. D., Bishop, D., and Randolph, M. F. (2016). “Geotechnical characteristics and engineering properties of a lakebed sediment.” Géotechnique, in press.
Colreavy, C., O’Loughlin, C. D., and Ward, D. (2012). “Piezoball testing in soft lake sediments.” Proc., 4th Int. Conf. on Site Characterization, Vol. 2, CRC Press, Boca Raton, FL, 597–602.
Freeman, T. J., and Schüttenhelm, R. T. E. (1990). “A geotechnical investigation of a deep ocean site.” Geotechnical Aspects of Ocean Waste Disposal Symp., ASTM, Philadelphia, 255–275.
Gaudin, C., O’Loughlin, C. D., Hossain, M. S., Randolph, M. F., and Colliat, J. L. (2014). “Installation of suction caissons in Gulf of Guinea clay.” Proc., 8th Int. Conf. on Physical Modelling in Geotechnics, CRC Press/A.A. Balkema, Leiden, Netherlands, 493–499.
Graham, J., Crooks, J. H. A., and Bell, A. L., (1983). “Time effects on the stress-strain behaviour of natural soft clays.” Géotechnique, 33(3), 327–340.
Hossain, M. S., Kim, Y., and Gaudin, C. (2014). “Experimental investigation of installation and pullout of dynamically penetrating anchors in clay and silt.” J. Geotech. Geoenviron. Eng., 04014026.
Hossain, M. S., O’Loughlin, C. D., and Kim, Y. (2015). “Dynamic installation and monotonic pullout of a torpedo anchor in calcareous silt.” Géotechnique, 65(2), 77–90.
Jeanjean, P., Znidarcic, D., Phillips, R., Ko, H. Y., Pfister, S., and Schroeder, K. (2006). “Centrifuge testing on suction anchors: Doublewall, stiff clays, and layered soil profile.” Proc., 2002 Offshore Technology Conf., Houston.
Jeong, S. W., Leroueil, S., and Locat, J. (2009). “Applicability of power law for describing the rheology of soils of different origins and characteristics.” Can. Geotech. J., 46(9), 1011–1023.
Karlsrud, K., Kalsnes, B., and Nowacki, F. (1993). “Response of piles in soft clay and silt deposits to static and cyclic axial loading based on recent instrumented pile load tests.” Proc., Offshore Site Investigation and Foundation Behaviour, Volume 28 of the Series Advances in Underwater Technology, Ocean Science and Offshore Engineering, London, 549–583.
Lehane, B. M., O’Loughlin, C. D., Gaudin, C., and Randolph, M. F. (2009). “Rate effects on penetrometer resistance in kaolin.” Géotechnique, 59(1), 41–52.
Lieng, J. T., Hove, F., and Tjelta, T. I. (1999). “Deep penetrating anchor: Subseabed deepwater anchor concept for floaters and other installations.” Proc., 9th Int. Offshore and Polar Engineering Conf., ISOPE, Cupertino, CA.
Lieng, J. T., Kavli, A., Hove, F., and Tjelta, T. I. (2000). “Deep penetrating anchor: Further development, optimization and capacity verification.” Proc., 10th Int. Offshore and Polar Engineering Conf., ISOPE, Cupertino, CA.
Lieng, J. T., Tjelta, T. I., and Skaugset, K. (2010). “Installation of two prototype deep penetrating anchors at the Gjøa Field in the North Sea.” Proc., 2010 Offshore Technology Conf., OTC, Houston.
Low, H. E., Randolph, M. F., DeJong, J. T., and Yafrate, N. J. (2008). “Variable rate full-flow penetration tests in intact and remoulded soil.” Proc., 3rd Int. Conf. on Site Characterization, Taylor & Francis/A.A. Balkema, Leiden, Netherlands, 1087–1092.
Lunne, T., Uzielli, M., and Long, M. (2006). “Characterisation and engineering properties of Troll Clay.” Proc., 2nd Int. Workshop on Characterisation and Engineering Properties of Natural Soils, CRC Press, Boca Raton, FL.
Medeiros, C. J., Jr. (2002). “Low cost anchor system for flexible risers in deep waters.” Proc., 2002 Offshore Technology Conf., OTC, Houston.
Morton, J. P., O’Loughlin, C. D., and White, D. J. (2016a). “Centrifuge modelling of an instrumented free-fall sphere for measurement of undrained strength in fine-grained soils.” Can. Geotech. J., 53(6), 918–929.
Morton, J. P., O’Loughlin, C. D., and White, D. J. (2016b). “Estimation of soil strength in fine-grained soils by instrumented free-fall sphere tests.” Géotechnique, 66(12), 959—968.
Neubecker, S. R., and Randolph, M. F. (1995). “Profile and frictional capacity of embedded anchor chains.” J. Geotech. Eng., 797–803.
NGI (Norwegian Geotechnical Institute). (2008). “Troll deep penetrating anchor tests.”, Oslo, Norway.
O’Beirne, C. P., O’Loughlin, C. D., and Gaudin, C. (2015a). “Soil response in the wake of dynamically installed projectiles.” Géotech. Lett., 5(3), 153–160.
O’Beirne, C. P., O’Loughlin, C. D., and Gaudin, C. (2017). “Assessing the penetration resistance acting on a dynamically installed anchor in normally consolidated and overconsolidated clay.” Can. Geotech. J., 54(1), 1–17.
O’Beirne, C. P., O’Loughlin, C. D., Wang, D., and Gaudin, C. (2015b). “Capacity of dynamically installed anchors as assessed through field testing and three dimensional large deformation finite element analyses.” Can. Geotech. J., 52(5), 548–562.
O’Loughlin, C. D, Richardson, M. D., and Randolph, M. F. (2009). “Centrifuge tests on dynamically installed anchors.” Proc., 28th Int. Conf. on Ocean, Offshore and Arctic Engineering, ASME, New York.
O’Loughlin, C. D., Blake, A. P., and Gaudin, C. (2016). “Towards a simple design procedure for dynamically embedded plate anchors.” Géotechnique, 66(9), 741—753.
O’Loughlin, C. D., Gaudin, C., Morton, J. P., and White, D. J. (2014). “MEMS accelerometers for measuring dynamic penetration events in geotechnical centrifuge tests.” Int. J. Phys. Modell. Geotech., 14(2), 31–39.
O’Loughlin, C. D., Randolph, M. F., and Richardson, M. (2004). “Experimental and theoretical studies of deep penetrating anchors.” Proc., 2004 Offshore Technology Conf., OTC, Houston.
O’Loughlin, C. D., Richardson, M. D., Randolph, M. F., and Gaudin, C. (2013). “Penetration of dynamically installed anchors in clay.” Géotechnique, 63(11), 909–919.
Øye, I. (2000). “Simulation of trajectories for a deep penetrating anchor.”, Trondheim, Norway.
Pang, C., Xu, L., Chen, H., Ren, B., and Tao, G. (2016). “The ballistic of fragment penetration into clay soil.” Proc., 29th Int. Symp. on Ballistics, DEStech Publications, Lancaster, PA.
Raie, M. S., and Tassoulas, J. L. (2009). “Installation of torpedo anchors: Numerical modelling.” J. Geotech. Geoenviron. Eng., 1805–1813.
Randolph, M. F. (2003). “Science and empiricism in pile foundation design.” Géotechnique, 53(10), 847–875.
Randolph, M. F., and White, D. J. (2012). “Interaction forces between pipelines and submarine slides—A geotechnical viewpoint.” Ocean Eng., 48, 32–37.
Sabetamal, H., Nazem, M., and Carter, J. P. (2013). “Numerical analysis of torpedo anchors.” Proc., 3rd Int. Symp. on Computational Geomechanics, International Centre for Computational Engineering, Rhodes, Greece.
Sahdi, F., Gaudin, C., White, D. J., Boylan, N., and Randolph, M. F. (2014). “Centrifuge modelling of active slide—Pipeline loading in soft clay.” Géotechnique, 64(1), 16–27.
Sheahan, T. C., Ladd, C. C., and Germaine, J. T., (1996). “Rate-dependent undrained shear behavior of saturated clay.” J. Geotech. Eng., 99–108.
Shelton, J. T., Nie, C., and Shuler, D. (2011). “Installation penetration of gravity installed plate anchors—Laboratory study results and field history data.” Proc., Offshore Technology Conf., OTC, Houston.
Skempton, A. W. (1951). “The bearing capacity of clays.” Proc., Building Research Congress, London, 1, 180–189.
Steiner, A., (2014). “In situ dynamic piezocone penetrometer tests in natural clayey soils-a reappraisal of strainrate corrections.” Can. Geotech. J., 51(3), 272–288.
Sturm, H., Lieng, J. T., and Saygili, G. (2011). “Effect of soil variability on the penetration depth of dynamically installed drop anchors.” Proc., Offshore Technology Conf., OTC, Houston.
Tanaka, H., and Locat, J. (1999). “A microstructural investigation of Osaka Bay clay: The impact of microfossils on its mechanical behaviour.” Can. Geotech. J., 36(3), 493–508.
Tika, T. E., and Hutchinson, J. N. (1999). “Ring shear tests on soil from the Vaiont landslide slip surface.” Géotechnique, 49(1), 59–74.
Yuan, F., White, D. J., and O’Loughlin, C. D. (2017). “The evolution of seabed stiffness during cyclic movement in a riser touchdown zone on soft clay.” Géotechnique, 67(2), 127–137.
Zhu, H., and Randolph, M. F. (2011). “Numerical analysis of a cylinder moving through rate-dependent undrained soil.” Ocean Eng., 38(7), 943–953.
Zimmerman, E. H., Smith, M. W., Shelton, J. T., and Systems, D. (2009). “Efficient gravity installed anchor for deepwater mooring.” Proc., 2009 Offshore Technology Conf., OTC, Houston.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 143 • Issue 9 • September 2017
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jul 6, 2016
Accepted: Jan 26, 2017
Published online: May 30, 2017
Published in print: Sep 1, 2017
Discussion open until: Oct 30, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.