Examining Setup Mechanisms of Driven Piles in Sand Using Laboratory Model Pile Tests
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 141, Issue 3
Abstract
In this study, model pile tests were carried out in a custom-made pressurized chamber to explore the mechanisms of a driven pile setup in dry sand. A bender element system and tactile pressure sensors were used in parallel to monitor the stiffness and stress changes in the soil surrounding the pile during the test. The experimental results demonstrate that pile setup is not caused by the increase in at-rest radial stress . Instead, it is mainly attributed to the increase in radial stress during pile loading , as a result of soil aging (or creep). Pile installation pushes the surrounding soil to the side, thereby imposing additional loading on the soil inside the influence zone. This loading action initiates an associated aging (or creep) process during the setup period; the aging effects ultimately give rise to an increase in both and pile shaft resistance. The measurements also reveal that the increase in aging-induced soil stiffness is due to contact normal forces among soil particles gradually becoming more homogenized during the setup period. This suggested setup mechanism could explain the absence of pile setup in bored (nondisplacement) piles—the loading action induced by pile installation is too insignificant to trigger the required aging process. Using a similar logic, the mechanism could elucidate why the setup rate is higher in large-displacement piles than in small-displacement piles.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by the Hong Kong Research Grants Council (GRF 620310). The authors are grateful to reviewers for valuable comments.
References
Anderson, D. G., and Stokoe, K. H., II. (1978). “Shear modulus: A time dependent soil property.” STP 654, ASTM, West Conshohocken, PA, 66–90.
Åstedt, B., Weiner, L., and Holm, G. (1992). “Increase in bearing capacity with time for friction piles in silt and sand.” Proc., Nordic Geotechnical Meeting, Danish Geotechnical Society, Lyngby, 411–416.
Axelsson, G. (2000). “Long-term set-up of driven piles in sand.” Ph.D. thesis, Royal Institute of Technology, Stockholm, Sweden.
Axelsson, G. (2002). “A conceptual model of pile set-up for driven piles in non-cohesive soil.” Deep Foundations 2002: An Int. Perspective on Theory, Design, Construction, and Performance (Geotechnical Special Publication), ASCE, Reston, VA, 64–79.
Baxter, D. D. P., and Mitchell, J. K. (2004). “Experimental study on the aging of sands.” J. Geotech. Geoenviron. Eng., 1051–1062.
Bolton, M. D., et al. (1999). “Centrifuge cone penetration tests in sand.” Geotechnique, 49(4), 543–552.
Bowman, E. T., and Soga, K. (2005). “Mechanisms of setup of displacement piles in sand: Laboratory creep tests.” Can. Geotech. J., 42(5), 1391–1407.
Bullock, P. J. (2008). “The easy button for driven pile setup: Dynamic testing.” From Research to Practice in Geotechnical Engineering, J. E. Laier, D. K. Crapps, and M. H. Hussein, eds., ASCE, Reston, VA, 471–488.
Bullock, P. J., Schmertmann, J. H., McVay, M. C., and Townsend, F. C. (2005a). “Side shear setup. I: Test piles driven in Florida.” J. Geotech. Geoenviron. Eng., 292–300.
Bullock, P. J., Schmertmann, J. H., McVay, M. C., and Townsend, F. C. (2005b). “Side shear setup. II: Results from Florida test piles.” J. Geotech. Geoenviron. Eng., 301–310.
Chow, F. C., Jardine, R. J., Brucey, F., and Nauroy, J. F. (1998). “Effects of time on capacity of pipe piles in dense marine sand.” J. Geotech. Geoenviron. Eng., 254–264.
Dai, S., Wuttke, F., and Santamarina, J. C. (2013). “Coda wave analysis to monitor processes in soils.” J. Geotech. Geoenviron. Eng., 1504–1511.
Daramola, O. (1980). “Effect of consolidation age on stiffness of sand.” Geotechnique, 30(2), 213–216.
Fellenius, B. H., Riker, R. E., O’Brien, A. J., and Tracy, G. R. (1989). “Dynamic and static testing in soil exhibiting set-up.” J. Geotech. Eng., 984–1001.
Fleming, K., Weltman, A., Randolph, M., and Elson, K. (2009). Piling engineering, Taylor & Francis Group, London.
Gao, Y. (2012). “Experimental characterizations and DEM simulations of aging creep structuration in sand.” Ph.D. thesis, Hong Kong Univ. of Science and Technology, Hong Kong.
Gao, Y., and Wang, Y. H. (2013). “Calibration of tactile pressure sensors for measuring stress in soils.” Geotech. Test. J., 36(4), 568–574.
Gao, Y., Wang, Y. H., and Su, J. C. P. (2013). “Mechanisms of aging induced modulus changes in sand under isotropic and anisotropic loading.” J. Geotech. Geoenviron. Eng., 470–482.
Gui, M. W., et al. (1998). “Guidelines for cone penetration tests in sand.” Proc., Int. Conf. Centrifuge 98, CRC Press/Balkema, Leiden, Netherlands, 155–160.
Guo, W. D. (2013). Theory and practice of pile foundations, CRC Press, Taylor & Francis Group, Boca Raton, FL.
Howie, J. A., Shozen, T., and Vaid, Y. P. (2002). “Effect of ageing on stiffness of very loose sand.” Can. Geotech. J., 39(1), 149–156.
Jardine, R. J., Standing, J. R., and Chow, F. C. (2006). “Some observations of the effects of time on the capacity of driven piles in sand.” Geotechnique, 56(4), 227–244.
Jardine, R. J., Zhu, B. T., Foray, P., and Yang, Z. X. (2013). “Interpretation of stress measurements made around closed-ended displacement piles in sand.” Geotechnique, 63(8), 613–627.
Klotz, E. U., and Coop, M. R. (2001). “An investigation of the effect of soil state on the capacity of driven piles in sands.” Geotechnique, 51(9), 733–751.
Lehane, B. M., Jardine, R. J., Bond, A. J., and Frank, R. (1993). “Mechanisms of shaft friction in sand from instrumented pile tests.” J. Geotech. Eng., 19–35.
Ng, E. S., Tsang, S. K., and Auld, B. C. (1988). “Pile foundation: The behaviour of piles in cohesionless soils.”, Federal Highway Administration, Washington, DC.
Radjai, F., Wolf, D. E., Jean, M., and Moreau, J. J. (1998). “Bimodal character of stress transmission in granular packings.” Phys. Rev. Lett., 80(1), 61–64.
Salgado, R., Mitchell, J. K., Jamiolkowski, M. (1998). “Calibration chamber size effects on penetration resistance in sand.” J. Geotech. Geoenviron. Eng., 878–888.
Samson, L., and Authier, J. (1986). “Changes in pile capacity with time: case histories.” Can. Geotech. J., 23(2), 174–180.
Shek, M. P., Zhang, L. M., and Pang, W. H. (2006). “Set-up effect in long piles in weathered soils.” Geotech. Eng., Proc., Inst. Civ. Eng., 159(3), 145–152.
Skov, R., and Denver, H. (1988). “Time-dependence of bearing capacity of piles.” Proc., 3rd Int. Conf. on the Application of Stress-Wave Theory to Piles, BiTech Publishers, Richmond, BC, Canada, 879–888.
Tavenas, F., and Audy, R. (1972). “Limitations of the driving formulas for predicting bearing capacities of piles in sand.” Can. Geotech. J., 9(1), 47–62.
Wang, Y. H., and Gao, Y. (2013). “Mechanisms of aging-induced modulus changes in sand with inherent fabric anisotropy.” J. Geotech. Geoenviron. Eng., 1590–1603.
Wang, Y. H., and Tsui, K. Y. (2009). “Experimental characterization of dynamic property changes in aged sands.” J. Geotech. Geoenviron. Eng., 259–270.
Wang, Y. H., Xu, D., and Tsui, K. Y. (2008). “Discrete element modeling of contact creep and aging in sand.” J. Geotech. Geoenviron. Eng., 1407–1411.
White, D. J., and Bolton, M. D. (2004). “Displacement and strain paths during plane-strain model pile installation in sand.” Geotechnique, 54(6), 375–397.
White, D. J., Schneider, J. A., and Lehane, B. M. (2005). “The influence of effective area ratio on shaft friction of displacement piles in sand.” Proc., Int. Symp. Frontiers Offshore Geomech., CRC Press/Balkema, Leiden, Netherlands, 741–747.
Yang, J. (2006). “Influence zone for end bearing of piles in sand.” J. Geotech. Geoenviron. Eng., 1229–1237.
Yang, L., and Liang, R. (2009). “Incorporating setup into load and resistance factor design of driven piles in sand.” Can. Geotech. J., 46(3), 296–305.
York, D. L., Walter, G. B., Clemente, F. M., and Law, S. K. (1994). “Set-up and relaxation in glacial sand.” J. Geotech. Eng., 1498–1513.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Mar 6, 2014
Accepted: Oct 28, 2014
Published online: Dec 2, 2014
Published in print: Mar 1, 2015
Discussion open until: May 2, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.