Sleeper End Resistance of Ballasted Railway Tracks
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 140, Issue 5
Abstract
This paper describes model tests used to investigate how ballast shoulder width and height contribute to a railway sleeper’s resistance to lateral movement for a range of shoulder widths and heights. Deflection and resistance were measured and photographs taken during the tests. The photographs were analyzed using a digital image correlation technique to identify the zones of ballast surface disturbance, which demonstrated that a bulbed failure volume was mobilized at the ultimate limit state. An idealized three-dimensional failure mechanism is proposed, and resistances are calculated using the limit equilibrium approach. The calculation provides a reliable estimate of the measured resistance. The work identifies the optimum shoulder width and height. The calculations are extended to demonstrate that when a number of sleepers are moved simultaneously, the sleeper end resistance may be one-third less per sleeper than that indicated in tests on an isolated sleeper. Image analysis and limit equilibrium calculations show that this is caused by overlapping of mobilized failure volumes from adjacent sleepers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers are grateful for the financial support of the Engineering and Physical Sciences Research Council (EPSRC). This work was made possible by combining techniques developed in two separate EPSRC grants: (1) “Development and role of structure in railway ballast,” EP/F062591/1 and (2) “Micro-Mechanical Behaviour of Locked Sands,” GR/T22896/01. The writers also acknowledge and thank research students Sinthuja Aingaran and Sharif Ahmed for their contributions related to the development and use of scaled ballast.
References
Aingaran, S. (2014). “Experimental investigation of static and cyclic behaviour of scaled railway ballast and the effect of stress reversal.” Ph.D. dissertation, Faculty of Engineering and the Environment, Univ. of Southampton, Southampton, U.K.
Anderson, W., and Fair, P. (2008). “Behavior of railroad ballast under monotonic and cyclic loading.” J. Geotech. Geoenviron. Eng., 316–327.
Aursudkij, B., McDowell, G. R., and Collop, A. C. (2009). “Cyclic loading of railway ballast under triaxial conditions and in a railway test facility.” Granul. Matter, 11(6), 391–401.
Bhandari, A. R., Powrie, W., and Harkness, R. M. (2012). “A digital image-based deformation measurement system for triaxial tests.” J. ASTM Geotech Test., 35(2), 209–226.
European Rail Research Institute (ERRI). (1995). “Committee D202: Improved knowledge of forces in CWR track (including switches), Report 2, Review of existing experimental work in behaviour of CWR track.” Utrecht, Netherlands.
Fukushima, S., and Tatsuoka, F. (1984). “Strength and deformation characteristics of saturated sand at extremely low pressures.” Soils Found., 24(4), 30–48.
Geotechnical Digital Systems (GDS). (2014). “Geotechnical Digital Systems instruments.” 〈http://www.gdsinstruments.com/gds-products/triaxial-automated-system-load-frame-type〉 (Jan. 6, 2014).
Henkel, D. J., and Gilbert, G. D. (1952). “The effect of the rubber membrane on the measured triaxial compression strength of clay samples.” Geotechnique, 3(1), 20–29.
Indraratna, B., Ionescu, D., and Christie, H. (1998). “Shear behavior of railway ballast based on large-scale triaxial tests.” J. Geotech. Geoenviron. Eng., 439–449.
Kabo, E. (2006). “A numerical study of the lateral ballast resistance in railway tracks.” Proc., Inst. Mech. Eng. Part F: J. Rail Rapid Transit, 220(4), 425–433.
Le Pen, L., and Powrie, W. (2011). “Contribution of base, crib, and shoulder ballast to the lateral sliding resistance of railway track: A geotechnical perspective.” Proc., Inst. Mech. Eng. Part F: J. Rail Rapid Transit, 225(2), 113–129.
Le Pen, L., Powrie, W., Zervos, A., Ahmed, S., and Aingaran, S. (2013). “Dependence of shape on particle size for a crushed rock railway ballast.” Granul. Matter, 15(6), 849–861.
Leps, T. M. (1970). “Review of shearing strength of rockfill.” J. Soil Mech. Found. Eng. Div., 96(4), 1159–1170.
Office for Research and Experiments of the International Union of Railways (ORE). (1976). “A study of the factors influencing the resistance to transverse displacement of unloaded track.” Committee D 117 Report 8, Utrecht, Netherlands.
Powrie, W. (2004). Soil mechanics: Concepts and applications, Spon, London.
Rail Safety and Standards Board (RSSB). (2003). “Railway group standard: Track system requirements.” GC/RT5021, London.
Railtrack. (2000). “Safety and standards directorate, railtrack line specification: Track ballast and stoneblower aggregate.” RT/CE/S/006, London.
Raymond, G. P., and Davies, J. R. (1978). “Triaxial tests on dolomite railroad ballast.” J. Geotech. Engrg. Div., 104(6), 737–751.
Selig, E. T., and Waters, J. M. (1994). Track geotechnology and substructure management, Telford, London.
Sevi, A. F. (2008). “Physical modeling of railroad ballast using the parallel gradation scaling technique within the cyclical triaxial framework.” Ph.D. thesis, Missouri Univ. of Science and Technology, Rolla, MO.
Suiker, A. S. J., Selig, E. T., and Frenkel, R. (2005). “Static and cyclic triaxial testing of ballast and subballast.” J. Geotech. Geoenviron. Eng., 771–782.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Mar 6, 2013
Accepted: Dec 17, 2013
Published online: Jan 13, 2014
Published in print: May 1, 2014
Discussion open until: Jun 13, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.