Measurements and Numerical Simulations of Inherent Stiffness Anisotropy in Soft Taipei Clay
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 140, Issue 1
Abstract
Soils are generally known not to be isotropic materials. The inherent anisotropy of clays results from the deposition process, which tends to induce a horizontal bedding plane in the soil layer. In this paper, the anisotropy of clays was studied to obtain more accurate analytical results for geotechnical problems, especially for deep excavations in soft clay with nearby structures. A series of -consolidated undrained triaxial compression () tests thus was conducted on tube samples of natural Taipei silty clay with multidirectional bender elements. A newly designed triaxial testing system equipped with a high-precision servo motor and local strain sensors was developed. A new soil suction-control system was also developed to perform soil saturation for triaxial tests. The suction-control system was used to reduce the change in the void ratio during saturation in the triaxial tests. Soil samples were retrieved from a site near a well-documented excavation case in Taipei. The anisotropy ratios for both the shear modulus and the undrained Young’s modulus were obtained by performing small-strain triaxial tests. The test results indicated that the anisotropy ratios of the shear moduli at the end of reconsolidation ranged from 1.15 to 1.44. Soils with higher overconsolidation ratio values had higher anisotropy ratios. Numerical simulations for an excavation case history were performed using a developed small-strain soil model that incorporates the anisotropy in the soil stiffness. The analysis results showed that differences between the anisotropic and isotropic models for the wall displacements, ground-surface settlements, and lateral soil movement behind the wall ranged from 10 to 43% at specified depths.
Get full access to this article
View all available purchase options and get full access to this article.
References
Arulnathan, R., Boulanger, R. W., and Riemer, M. F. (1998). “Analysis of bender element tests.” Geotech. Test. J., 21(2), 120–131.
Atkinson, J. H., and Sallfors, G. (1991). “Experimental determination of soil properties.” Proc., 10th European Conf. on Soil Mechanics and Foundation Engineering, Vol. 3, Florence, Italy, 915–956.
Benz, T. (2007). “Small-strain stiffness of soils and its numerical consequences.” Ph.D. dissertation, Univ. of Stuttgart, Stuttgart, Germany.
Brignoli, E. G. M., Gotti, M., and Stokoe, K. H., II. (1996). “Measurement of shear waves in laboratory specimens by means of piezoelectric transducers.” Geotech. Test. J., 19(4), 384–397.
Burland, J. B. (1989). “Ninth Laurits Bjerrum Memorial Lecture. ‘Small is beautiful’: The stiffness of soils at small strains.” Can. Geotech. J., 26(4), 499–516.
Cho, W., and Finno, R. J. (2010). “Stress-strain responses of block samples of compressible Chicago glacial clays.” J. Geotech. Geoenviron. Eng., 136(1), 178–188.
Cho, W., Holman, T. P., Jung, Y.-H., and Finno, R. J. (2007). “Effects of swelling during saturation in triaxial tests in clays.” Geotech. Test. J., 30(5), 378–386.
Clayton, C. R. I., Khatrush, S. A., Bica, A. V. D., and Siddique, A. (1989). “The use of Hall effect semiconductors in geotechnical instrumentation.” Geotech. Test. J., 12(1), 69–76.
Duncan, J. M., and Chang, C. Y. (1970). “Nonlinear analysis of stress and strain in soils.” J. Soil Mech. and Found. Div., 96(5), 637–659.
Finno, R. J., and Tu, X. (2006). “Selected topics in numerical simulation of supported excavations.” Proc., Int. Conf. of Construction Processes in Geotechnical Engineering for Urban Environment, Taylor and Francis, London, 3–20.
Gasparre, A., Nishimura, S., Mihn, N. A., Coop, M. R., and Jardine, R. J. (2007). “The stiffness of natural London clay.” Geotechnique, 57(1), 33–47.
Gibson, R. E. (1974). “The analytical method in soil mechanics.” Geotechnique, 24(2), 115–140.
Hashash, Y. M. A., and Whittle, A. J. (1996). “Ground movement prediction for deep excavations in soft clay.” J. Geotech. Engrg., 122(6), 474–486.
Hashash, Y. M. A., and Whittle, A. J. (2002). “Mechanisms of load transfer and arching for braced excavations in clay.” J. Geotech. Geoenviron. Eng., 128(3), 187–197.
Hsieh, P. G., and Ou, C. Y. (2011). “Analysis of nonlinear stress and strain in clay under the undrained condition.” J. Mech., 27(2), 201–213.
Jardine, R. J., Potts, D. M., Fourie, A. B., and Burland, J. B. (1986). “Studies of the influence of non-linear characteristics in soil-structure interaction.” Geotechnique, 36(3), 377–396.
Jovicic, V., Coop, M. R., and Simic, M. (1996). “Objective criteria for determining Gmax from bender element test.” Geotechnique, 46(2), 357–362.
Kung, G. T. C. (2007). “Equipment and testing procedures for small strain triaxial tests.” J. Chin. Inst. Eng., 30(4), 579–591.
Kung, G. T. C., Juang, C. H., Hsiao, E. C. L., and Hashash, Y. M. A. (2007). “Simplified model for wall deflection and ground surface settlement caused by braced excavation in clays.” J. Geotech. Geoenviron. Eng., 133(6), 731–747.
Kuwano, R., and Jardine, R. J. (1998). “Stiffness measurements in a stress path cell.” Prefailure behaviour of geomaterials, Part 3, Thomas Telford, London, 391–395.
Ladd, C. C., and DeGroot, D. J. (2003). “Recommended practice for soft ground site characterization.” Proc., 12th Panamerican Conf. on Soil Mechanics and Geotechnical Engineering, Boston, 3–57.
Lee, K. M., and Rowe, R. K. (1989). “Deformations caused by surface loading and tunnelling: The role of elastic anisotropy.” Geotechnique, 39(1), 125–140.
Lim, A., Ou, C. Y., and Hsieh, P. G. (2010). “Evaluation of clay constitutive models for analysis of deep excavation under undrained condition.” J. GeoEng., 5(1), 9–20.
Lings, M. L. (2001). “Drained and undrained elastic stiffness parameters.” Geotechnique, 51(6), 555–565.
Mair, R. J. (1993). “Unwin Memorial Lecture: Developments in geotechnical engineering research: Applications to tunnels and deep excavation.” Proc., Institution of Civil Engineers and Civil Engineering, ICE, London, 27–41.
Mesri, G., and Huvaj, N. (2007). “Shear strength mobilized in undrained failure of soft clay and silt deposits.” Proc., Geo-Denver 2007 Conf., ASCE, New York, 1–22.
Ng, C. W. W., Leung, E. H. Y., and Lau, C. K. (2004). “Inherent anisotropic stiffness of weathered geomaterial and its influence on ground deformations around deep excavations.” Can. Geotech. J., 41(1), 12–24.
Nishimura, S., Nishiyama, T., and Murakami, A. (2005). “Inverse analysis of soft grounds considering nonlinearity and anisotropy.” Soils Found., 45(2), 87–95.
Osouli, A., Hashash, Y. M. A., and Song, H. (2010). “Interplay between field measurements and soil behavior for capturing supported excavation response.” J. Geotech. Geoenviron. Eng., 136(1), 69–84.
Ou, C. Y., and Lai, C. H. (1994). “Finite-element analysis of deep excavation in layered sandy and clayey soil deposits.” Can. Geotech. J., 31(2), 204–214.
Ou, C. Y., Liao, J. T., and Cheng, W. L. (2000a). “Building response and ground movements induced by a deep excavation.” Geotechnique, 50(3), 209–220.
Ou, C. Y., Liao, J. T., and Lin, H. D. (1998). “Performance of diaphragm wall constructed using top-down method.” J. Geotech. Geoenviron. Eng., 124(9), 798–808.
Ou, C. Y., Shiau, B. Y., and Wang, I. W. (2000b). “Three-dimensional deformation behavior of the Taipei National Enterprise Center (TNEC) excavation case history.” Can. Geotech. J., 37(2), 438–448.
Pennington, D. S., Nash, D. F. T., and Lings, M. L. (1997). “Anisotropy of G0 shear stiffness in Gault clay.” Geotechnique, 47(3), 391–398.
Pennington, D. S., Nash, D. F. T., and Lings, M. L. (2001). “Horizontally mounted bender elements for measuring anisotropic shear moduli in triaxial clay specimens.” Geotech. Test. J., 24(2), 133–144.
PLAXIS 2D 8.6 [Computer software]. Delft, Netherlands, PLAXIS.
Schuster, M., Kung, G. T.-C., Juang, C. H., and Hashash, Y. M. A. (2009). “Simplified model for evaluating damage potential of buildings adjacent to a braced excavation.” J. Geotech. Geoenviron. Eng., 135(12), 1823–1835.
Simpson, B., and Ng, C. W. W. (1995). “Anisotropic analysis of settlement trough due to tunnelling in an overconsolidated clay.” Proc., 10th Asian Regional Conf. on Soil Mechanics and Foundation Engineering, Vol. 2, International Academic Publisher, Beijing, 166–167.
Teng, F.-C., and Ou, C.-Y. (2011). “Application of a suction control system to the saturation process in triaxial tests.” Geotech. Test. J., 34(6), 613–622.
Teng, F.-C., and Ou, C.-Y. (2013). “Using a direct-drive motor to measure the strain in triaxial tests.” Proc. of ICE Geotech. Eng., 166(1), 56–66.
Viggiani, G., and Atkinson, J. H. (1995). “Interpretation of bender element tests.” Geotechnique, 45(1), 149–154.
Whittle, A. J., DeGroot, D. J., Ladd, C. C., and Seah, T.-H. (1994). “Model prediction of anisotropic behavior of Boston blue clay.” J. Geotech. Engrg., 120(1), 199–224.
Whittle, A. J., and Kawadas, M. J. (1994). “Formulation of the MIT-E3 constitutive model for overconsolidated clays.” J. Geotech. Engrg., 120(1), 173–198.
Zhang, C.-Y. (1996). “A study of the deformation characteristics of the Taipei silty clay.” Master’s thesis, National Taiwan Univ. of Science and Technology, Taipei, Taiwan.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 140 • Issue 1 • January 2014
Pages: 237 - 250
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jan 20, 2012
Accepted: Jul 19, 2013
Published online: Jul 25, 2013
Published in print: Jan 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.