Effects of Principal Stress Directions on 3D Failure Conditions in Cross-Anisotropic Sand
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 140, Issue 2
Abstract
An experimental program was carried out to study the variation of shear strength of cross-anisotropic deposits of fine Nevada sand under three-dimensional (3D) conditions using a recently developed torsion shear apparatus. A total of 44 drained torsion shear tests were performed at a constant mean confining stress, , constant intermediate principal stress ratios, as indicated by , and principal stress directions, . The experiments were performed on large hollow cylinder specimens deposited by dry pluviation and tested in an automated torsion shear apparatus. The specimens had a height of 40 cm, an average diameter of 20 cm, and a wall thickness of 2 cm. The 3D failure surface of fine Nevada sand is presented with discrete combinations of and intermediate principal stress. The effects of these two variables on the shape of the failure surface are presented. The friction angles are highest for for all -values and show a dip in strength with the lowest values near , at which the major principal stress is inclined such that the potential shear band directions coincide with the bedding planes, which exhibit the lowest strengths. Overall, the friction angle varies from 57 to 32°, while the conventional friction angle from a triaxial compression test on a vertical specimen produced 41°, which is often employed in a given geotechnical engineering project.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research presented here was performed with support from the National Science Foundation under Grant No. CMMI-0757827. Grateful appreciation is expressed for this support.
References
Abelev, A., and Lade, P. V. (2004). “Characterization of failure in cross-anisotropic soils.” J. Eng. Mech., 599–606.
Abelev, A. V., and Lade, P. V. (2003). “Effects of cross anisotropy on three-dimensional behavior of sand. I: Stress–strain behavior and shear banding.” J. Eng. Mech., 160–166.
Arthur, J. R. F., and Menzies, B. K. (1972). “Inherent anisotropy in a sand.” Geotechnique, 22(1), 115–128.
Arthur, J. R. F., and Phillips, A. B. (1975). “Homogeneous and layered sand in triaxial compression.” Geotechnique, 25(4), 799–815.
Brinch Hansen, J. (1966). “Stress-strain relationships for sand.” Bulletin No. 20, Danish Geotechnical Institute, Copenhagen, Denmark, 8–14.
Casagrande, A., and Carillo, N. (1944). “Shear failure of anisotropic materials.” J. Boston Soc. Civil Eng., 31(4), 122–135.
Duncan, J. M., and Seed, H. B. (1966). “Anisotropy and stress reorientation in clay.” J. Soil Mech. and Found. Div., 92(5), 21–50.
El-Sohby, M. A., and Andrawes, K. Z. (1973). “Experimental examination of sand anisotropy.” Proc., 8th Int. Conf. Soil Mechanics and Foundation Engineering, Vol. 1, International Society of Soil Mechanics and Foundation Engineering, 103–109.
Haruyama, M. (1981). “Anisotropic deformation-strength characteristics of an assembly of spherical particles under three dimensional stresses.” Soils Found., 21(4), 41–55.
Hight, D., Gens, A., and Symes, M. (1983). “The development of a new hollow cylinder apparatus for investigating the effects of principal stress rotation in soils.” Geotechnique, 33(4), 355–383.
Kirkgard, M. M., and Lade, P. V. (1991). “Anisotropy of normally consolidated San Francisco Bay mud.” Geotech. Test. J., 14(3), 231–246.
Kirkgard, M. M., and Lade, P. V. (1993). “Anisotropic three-dimensional behavior of a normally consolidated clay.” Can. Geotech. J., 30(5), 848–858.
LabView 8.5.1 [Computer software]. Austin, TX, National Instruments.
Lade, P. V. (1977). “Elasto-plastic stress-strain theory for cohesionless soil with curved yield surfaces.” Int. J. Solids Struct., 13(11), 1019–1035.
Lade, P. V. (1981). “Torsion shear apparatus for soil testing.” Laboratory shear strength of soil, STP740, R. N. Yong and F. C. Townsend, eds., ASTM, West Conshohocken, PA, 145–163.
Lade, P. V. (2007). “Modeling failure in cross-anisotropic frictional materials.” Int. J. Solids Struct., 44(16), 5146–5162.
Lade, P. V. (2008) “Failure criterion for cross-anisotropic soils.” J. Geotech. Geoenviron. Eng., 117–124.
Lade, P. V., and Abelev, A. V. (2003). “Effects of cross-anisotropy on three-dimensional behavior of sand. Part II: Volume change behavior and failure.” J. Eng. Mech.,, 167–174.
Lade, P. V., and Abelev, A. V. (2005). “Characterization of cross-anisotropic soil deposits from isotropic compression tests.” Soils Found., 45(5), 89–102.
Lade, P. V., and Wasif, U. (1988). “Effects of height-to-diameter ratio in triaxial specimens on the behavior of cross-anisotropic sand.” Advanced triaxial testing of soil and rock, STP977, R. T. Donaghe, R. C. Chaney, and M. L. Silver, eds., ASTM, West Conshohocken, PA, 706–714.
Lam, W. K., and Tatsuoka, F. (1988). “Triaxial compressive and extension strength of sand affected by strength anisotropy and sample slenderness.” Advanced triaxial testing of soil and rock, STP977, R. T. Donaghe, R. C. Chaney, and M. L. Silver, eds., ASTM, West Conshohocken, PA, 655–666.
Miura, K., Miura, S., and Toki, S. (1986). “Deformation behavior of anisotropic dense sand under principal stress axes rotation.” Soils Found., 26(1), 36–52.
Naughton, P. J., and O’Kelly, B. C. (2007). “Stress non-uniformity in a hollow cylinder torsional sand specimen.” Geomech. Geoeng., 2(2), 117–122.
Ochiai, H., and Lade, P. V. (1983). “Three-dimensional behavior of sand with anisotropic fabric.” J. Geotech. Engrg., 1313–1328.
Oda, M. (1972a). “Deformation mechanism of sand in triaxial compression.” Soils Found., 12(4), 45–63.
Oda, M. (1972b). “Initial fabrics and their relations to mechanical properties of granular material.” Soils Found., 12(1), 17–36.
Oda, M. (1972c). “The mechanism of fabric changes during compressional deformation of sand.” Soils Found., 12(2), 1–18.
Oda, M., Koishikawa, I., and Higuchi, T. (1978). “Experimental study of anisotropic shear strength of sand by plane strain test.” Soils Found., 18(1), 25–38.
O’Kelly, B., and Naughton, P. (2009). “Study of yielding of sand under generalized stress conditions using a versatile hollow cylinder torsional apparatus.” Mech. Mater., 41(3), 187–198.
Parkin, A. K., Gerrard, C. M., and Willoughby, D. R. (1969). “Discussion of ‘Deformation of sand in shear’.” J. Soil Mech. and Found. Div., 94(SM1), 336–340.
Pradel, D., Ishihara, K., and Gutierrez, M. (1990). “Yielding and flow of sand under principal stress axes rotation.” Soils Found., 30(1), 87–99.
Rodriguez, N. M., and Lade, P. V. (2013). “True triaxial tests on cross-anisotropic deposits of fine Nevada sand.” Int. J. Geomech., 779–793.
Saada, A. S. (1970). “Testing of anisotropic clay soils.” J. Soil Mech. and Found. Div., 96(5), 1847–1852.
Yamada, Y., and Ishihara, K. (1979). “Anisotropic deformation characteristics of sand under three dimensional stress conditions.” Soils Found., 19(2), 79–91.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Sep 6, 2012
Accepted: Jul 16, 2013
Published online: Nov 8, 2013
Published in print: Feb 1, 2014
Discussion open until: Apr 8, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.