Modeling Ground-Shell Contact Forces in NATM Tunneling Based on Three-Dimensional Displacement Measurements
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 139, Issue 3
Abstract
Based on an advanced micromechanics-based nonlinear creep model for shotcrete and thin shell kinematics, measured displacement data are first converted into in-plane stress fields throughout a shotcrete tunnel shell driven according to the New Austrian Tunneling Method (NATM). Subsequently, the partial differential equations for the local force equilibrium in the cylindrical coordinate directions are solved for out-of-plane shell stresses, inclusive of the tractions at the ground-shell interface. Results obtained for an NATM-tunnel driven through clayey ground at moderate depth show that the maximum shear tractions at the ground-shell interface may even exceed the maximum normal tractions (ground pressure). At the same time, even a young top heading tunnel shell may act as an arching thrust. The authors regard this method as a further step in the continously refined of interpretation of displacement measurements stemming from tunnel monitoring systems for the NATM, on a well-defined mechanical basis. This results in two structural models for top heading excavation stages, which might have the potential to support NATM predesign activities in the future.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
A scholarship granted by the Higher Education Commission of Pakistan to the first author for doctoral studies at the Vienna University of Technology is gratefully acknowledged.
References
Alejano, L., Rodriguez-Dono, A., Alonso, E., and Fdez.-Manín, G. (2009). “Ground reaction curves for tunnels excavated in different quality rock masses showing several types of post-failure behaviour.” Tunn. Undergr. Space Technol., 24(6), 689–705.
Apel, B. D., Gray, B. R., Moss, R. H., Watkins, S. E., and Jones, T. H. (2007). “Development and laboratory trials of the light-based high-resolution target movement monitor for monitoring convergence at underground mines.” J. Geotech. Geoenviron. Eng., 133(9), 1167–1171.
Azevedo, R., Parreira, A., and Zomberg, J. (2002). “Numerical analysis of a tunnel in residual soils.” J. Geotech. Geoenviron. Eng., 128(3), 227–236.
Barton, N., Lien, R., and Lunde, J. (1974). “Engineering classification of rock masses for the design of tunnel support.” Rock Mech., 6(4), 189–236.
Bernaud, D., Maghous, S., de Buhan, P., and Couto, E. (2009). “A numerical approach for design of bolt-supported tunnels regarded as homogenized structures.” Tunn. Undergr. Space Technol., 24(5), 533–546.
Bobet, A., and Einstein, H. H. (2011). “Tunnel reinforcement with rockbolts.” Tunn. Undergr. Space Technol., 26(1), 100–123.
Boldini, D., Lackner, R., and Mang, H. (2005). “Ground-shotcrete interaction of NATM tunnels with high overburden.” J. Geotech. Geoenviron. Eng., 131(7), 886–897.
Bonapace, P. (1997). “Evaluation of stress measurements in NATM tunnels at the Jubilee Line Extension Project.” Tunn. People, Proc., World Tunn. Cong. 1997, J. Golser, W. Hinkel, and W. Schubert, eds., Vol. 1, Balkema, Rotterdam, Netherlands, 325–330.
Brandtner, M., Moritz, B., and Schubert, P. (2007). “On the challenge of evaluating stress in a shotcrete lining: Experiences gained in applying the hybrid analysis method.” Felsbau, 25(5), 93–98.
Carranza-Torres, C., and Fairhurst, C. (2000). “Application of the convergence-confinement method of tunnel design to rock masses that satisfy the Hoek-Brown failure criterion.” Tunn. Undergr. Space Technol., 15(2), 187–213.
Cirak, F., Ortiz, M., and Schröder, P. (2000). “Subdivision surfaces: A new paradigm for thin-shell finite-element analysis.” Int. J. Numer. Methods Eng., 47(12), 2039–2072.
de Buhan, P., Bourgeois, E., and Hassen, G. (2008). “Numerical simulation of bolt-supported tunnels by means of a multiphase model conceived as an improved homogenization procedure.” Int. J. Numer. Anal. Methods Geomech., 32(13), 1597–1615.
Fenner, R. (1938). “Untersuchungen zur Erkenntnis des Gebirgsdruckes [Investigation to gain insight into rock pressure].” Glückauf, 74(32), 681–695 and 705–715 (in German).
Finno, R., and Calvello, M. (2005). “Supported excavations: Observational method and inverse modeling.” J. Geotech. Geoenviron. Eng., 131(7), 826–836.
Fung, Y. (1965). Foundations of solid mechanics. Prentice-Hall international series in dynamics, Prentice Hall, Englewood Cliffs, NJ.
Fung, Y., and Tong, P. (2001). Classical and computational solid mechanics (advanced series in engineering science), World Scientific, Singapore.
Großauer, K., and Schubert, W. (2009). “Development of an expert system for the interpretation of displacement monitoring data.” Geomech. Tunn., 2(3), 260–268.
Hellmich, C. (1999). “Shotcrete as part of the New Austrian Tunneling Method: From thermochemomechanical material modeling to structural analysis and safety assessment of tunnels.” Ph.D. thesis, Vienna Univ. of Technology, Vienna, Austria.
Hellmich, C., Macht, J., and Mang, H. (1999a). “Ein hybrides Verfahren zur Bestimmung der Auslastung von Spritzbetonschalen auf der Basis von in-situ Verschiebungsmessungen und thermochemomechanischer Materialmodellierung [A hybrid method for determination of the degree of utilization of shotcrete tunnel linings on the basis of in-situ displacement measurements and thermochemomechanical material modeling].” Felsbau, 17(5), 422–425 (in German).
Hellmich, C., and Mang, H. (1999). “Influence of the dilatation of soild and shotcrete on the load bearing behavior of NATM-tunnels.” Felsbau 17(1), 35–43.
Hellmich, C., and Mang, H. (2005). “Shotcrete elasticity revisited in the framework of continuum micromechanics: From submicron to meter level.” J. Mater. Civ. Eng., 17(3), 246–256.
Hellmich, C., Mang, H., and Ulm, F.-J. (2001). “Hybrid method for quantification of stress states in shotcrete tunnel shells: Combination of 3D in situ displacement measurements and thermochemoplastic material law.” Comput. Struct., 79(22–25), 2103–2115.
Hellmich, C., Ulm, F.-J., and Mang, H. (1999b). “Consistent linearization in finite element analysis of coupled chemo-thermal problems with exo- or endothermal reactions.” Comput. Mech., 24(4), 238–244.
Huang, L., Xu, Z., and Zhou, C. (2009). “Modeling and monitoring in a soft argillaceous shale tunnel.” Acta Geotech., 4(4), 273–282.
Huo, H., Bobet, A., Fernandez, G., and Ramirez, J. (2005). “Load transfer mechanisms between underground structure and surrounding ground: Evaluation of the failure of the Daikai Station.” J. Geotech. Geoenviron. Eng., 131(12), 1522–1533.
Kainrath-Reumayer, S., Gschwandtner, G., and Galler, R. (2009). “The convergence confinement method as an aid in the design of deep tunnels.” Geomech. Tunn., 2(5), 553–560.
Kontogianni, V., Tzortzis, A., and Stiros, S. (2004). “Deformation and failure of the Tymfristos Tunnel, Greece.” J. Geotech. Geoenviron. Eng., 130(10), 1004–1013.
Kropik, C., and Mang, H. (1996). “Computational mechanics of the excavation of tunnels.” Eng. Comput., 13(7), 49–69.
Lackner, R., Macht, J., Hellmich, C., and Mang, H. (2002). “Hybrid method for analysis of segmented shotcrete tunnel linings.” J. Geotech. Geoenviron. Eng., 128(4), 298–308.
Lackner, R., Macht, J., and Mang, H. (2006). “Hybrid analysis method for on-line quantification of stress states in tunnel shells.” Comput. Methods Appl. Mech. Eng., 195(41–43), 5361–5376.
Macht, J., Lackner, R., Hellmich, C., and Mang, H. (2003). “Quantification of stress states in shotcrete shells.” Numerical simulation in tunneling, G. Beer, ed., Springer-Verlag, Vienna, Austria, 225–248.
Masin, D. (2009). “3D modeling of an NATM tunnel in high K0 clay using two different constitutive models.” J. Geotech. Geoenviron. Eng., 135(9), 1326–1335.
Ng, C., and Lee, G. (2005). “Three-dimensional ground settlements and stress-transfer mechanisms due to open-face tunnelling.” Can. Geotech. J., 42(4), 1015–1029.
Ng, C., Lee, K., and Tang, D. (2004). “Three-dimensional numerical investigations of New Austrian Tunnelling Method (NATM) twin tunnel interactions.” Can. Geotech. J., 41(3), 523–539.
Nguyen, T. D., Qi, H. J., Castro, F., and Long, K. N. (2008). “A thermoviscoelastic model for amorphous shape memory polymers: Incorporating structural and stress relaxation.” J. Mech. Phys. Solids, 56(9), 2792–2814.
Oettl, G., Stark, R. F., and Hofstetter, G. (1998). “A comparison of elastic-plastic soil models for 2D FE analyses of tunnelling.” Comput. Geotech., 23(1–2), 19–38.
Pacher, F. (2010). “Ground reaction and lining curves.” Geomech. Tunn., 3(4), 402–408.
Pellet, F. L. (2009). “Contact between a tunnel lining and a damage-susceptible viscoplastic medium.” Comput. Model. Eng. Sci., 52(3), 279–295.
Pichler, B., and Hellmich, C. (2010). “Upscaling quasi-brittle strength of cement-based materials: A continuum micromechanics approach.” Proc., EURO-C Conf. Comput. Model. Concrete Struct., N.Bićanić, R.de Borst, H.Mang, and G.Meschke, eds., Taylor and Francis, London, 225–248.
Pichler, B., and Hellmich, C. (2011). “Upscaling quasi-brittle strength of cement-based materials: A multiscale engineering mechanics approach.” Cement Concr. Res., 41(5), 467–476.
Pichler, B., Hellmich, C., and Eberhardsteiner, J. (2009). “Spherical and acicular representation of hydrates in a micromechanical model for cement paste: Prediction of early-age elasticity and strength.” Acta Mech., 203(3–4), 137–162.
Pichler, B., Scheiner, S., and Hellmich, C. (2008). “From micron-sized needle-shaped hydrates to meter-sized shotcrete tunnel shells: Micromechanical upscaling of stiffness and strength of hydrating shotcrete.” Acta Geotech., 3(4), 273–294.
Poleschinski, V. W., and Müller, P. (1999). “Geologische Dokumentation des Siebergtunnels und der Voreinschnitte [Geological documentation of Sieberg tunnel and the open cuts].” Felsbau, 17(2), 112–119 (in German).
Rabcewicz, L. (1969a). “Stability of tunnels under rock load, part I.” Water Power, 21(6), 225–229.
Rabcewicz, L. (1969b). “Stability of tunnels under rock load, part II.” Water Power, 21(7), 266–273.
Rabcewicz, L. (1969c). “Stability of tunnels under rock load, part III.” Water Power, 21(8), 297–302.
Radonćić, N., Schubert, W., and Moritz, B. (2009). “Ductile support design.” Geomech. Tunn., 2(5), 561–577.
Ramspacher, V. W. and Schwab, P. (1998). “Siebergtunnel, Vortrieb Pillgrab West—Planung und Ausführung [Driving of Sieberg tunnel towards west—planning and execution].” Österreichische Ingenieur und Architekten-Zeitschrift, 143(9), 302–305 (in German).
Riedmüller, G., and Schubert, W. (1999). “Critical comments on quantitative rock mass classifications.” Felsbau, 17(3), 164–167.
Rokahr, R. (1997). “Ein neues Verfahren zur täglichen Kontrolle der Auslastung einer Spritzbetonschale [A new method for daily monitoring of the stress intensity of a shotcrete lining].” Felsbau, 15(6), 430–434 (in German).
Salençon, J. (2001). Handbook of continuum mechanics, general concepts, thermoelasticity, Springer, New York.
Scheiner, S., and Hellmich, C. (2009). “Continuum microviscoelasticity model for aging basic creep of early-age concrete.” J. Eng. Mech., 135(4), 307–323.
Sercombe, J., Hellmich, C., Ulm, F.-J., and Mang, H. (2000). “Modeling of early-age creep of shotcrete. I: Model and model parameters.” J. Eng. Mech., 126(3), 284–291.
Shin, J., Potts, D., and Zdravkovic, L. (2002). “Three-dimensional modelling of NATM tunnelling in decomposed granite soil.” Geotechnique, 52(3), 187–200.
Steindorfer, A., and Schubert, W. (1997). “Application of new methods of monitoring data analysis for short term prediction in tunnelling.” Tunn. People, Proc., World Tunn. Cong., J. Golser, W. Hinkel, and W. Schubert, eds., Vol. 1, Balkema, Rotterdam, Netherlands, 9–65.
Sulem, J., Panet, M., and Guenot, A. (1987). “An analytical solution for time-dependent displacements in a circular tunnel.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 24(3), 155–164.
Terzaghi, K. (1946). “Rock defects and loads on tunnel supports.” Rock tunnelling with steel supports, R. Proctor and T. White, eds., Commercial Shearing Company, Youngstown, OH, 15–99.
Timoshenko, S. (1940). Theory of plates and shells, McGraw Hill, New York.
Ullah, S., Pichler, B., Scheiner, S., and Hellmich, C. (2010). “Shell-specific interpolation of measured 3D displacements, for micromechanics-based rapid safety assessment of shotcrete tunnels.” Comput. Model. Eng. Sci., 57(3), 279–316.
Ullah, S., Pichler, B., Scheiner, S., and Hellmich, C. (2012). “Influence of shotcrete composition on load level estimation in NATM tunnel shells: Micromechanics-based sensitivity analyses.” Int. J. Numer. Analyt. Methods Geomech., 36(9), 1151–1180.
Vardakos, S., and Gutierrez, M. (2006). “Simplified parameter identification for circular tunnels.” Tunn. Undergr. Space Technol., 21(3–4), 372.
Vardakos, S. S., Gutierrez, M. S., and Barton, N. R. (2007). “Back-analysis of Shimizu Tunnel No. 3 by distinct element modeling.” Tunn. Undergr. Space Technol., 22(4), 401–413.
Yoo, C., and Kim, S.-B. (2008). “Three-dimensional numerical investigation of multifaced tunnelling in water-bearing soft ground.” Can. Geotech. J., 45(10), 1467–1486.
Zhou, C., Zhu, H., and Li, X. (2008). “Application of infrared photography and image processing to tunnel construction with New Austrian Tunneling Method.” Chin. J. Rock Mech. Eng., 27(S1), 3166–3172.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 139 • Issue 3 • March 2013
Pages: 444 - 457
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 8, 2011
Accepted: Jun 14, 2012
Published online: Aug 1, 2012
Published in print: Mar 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.