Evaluation on Failure of Fiber-Reinforced Sand
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 139, Issue 1
Abstract
Fiber reinforcement can help to enhance soil strength, stabilize near-surface soil layers, and mitigate the risk of soil liquefaction. Evaluation of the strength of fiber-reinforced soils needs a proper failure criterion. This study presents a three-dimensional failure criterion for fiber-reinforced sand. By assuming that the total strength of the composite is a combination of the shear resistance of the host soil and the reinforcement of fibers, a general anisotropic failure criterion is proposed with special emphasis on the effect of isotropically/anisotropically distributed fibers. An anisotropic variable, defined by the joint invariant of the deviatoric stress tensor and a deviatoric fiber distribution tensor, is introduced in the criterion to quantify the fiber orientation with respect to the strain rate/stress direction at failure. With further consideration of the fiber concentration and other factors such as aspect ratio, the proposed criterion is applied to predicting the failure of fiber-reinforced sand in conventional triaxial compression/extension tests for both isotropically and anisotropically distributed fiber cases. The predictions are in good agreement with the test results available in the literature. The practical significance of using this criterion for such problems as inclined slope stabilization is briefly discussed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the Research Grants Council of Hong Kong (under Grant Nos. 623211 and SBI08/09.EG02).
References
Athanasopoulos, G. A. (1996). “Results of direct shear tests on geotextile reinforced cohesive soil.” Geotext. Geomembr., 14(11), 619–644.
Consoli, N. C., Casagrande, M. D. T., and Coop, M. R. (2007a). “Performance of a fibre-reinforced sand at large shear strains.” Geotechnique, 57(9), 751–756.
Consoli, N. C., Foppa, D., Festugato, L., and Heineck, K. S. (2007b). “Key parameters for strength control of artificially cemented soils.” J. Geotech. Geoenviron. Eng., 133(2), 197–205.
Consoli, N. C., Heineck, K. S., Casagrande, M. D. T., and Coop, M. R. (2007c). “Shear strength behavior of fiber-reinforced sand considering triaxial tests under distinct stress paths.” J. Geotech. Geoenviron. Eng., 133(11), 1466–1469.
Cui, L., and O’Sullivan, C. (2006). “Exploring the macro- and micro-scale response of an idealised granular material in the direct shear apparatus.” Geotechnique, 56(7), 455–468.
Diambra, A., Ibraim, E., Muir Wood, D., and Russell, A. R. (2010). “Fibre reinforced sands: Experiments and modeling.” Geotext. Geomembr., 28(3), 238–250.
Diambra, A., Russell, A. R., Ibraim, E., and Muir Wood, D. (2007). “Determination of fibre orientation distribution in reinforced sand.” Geotechnique, 57(7), 623–628.
Gao, Z. W., Zhao, J. D., and Yao, Y. P. (2010). “A generalized anisotropic failure criterion for geomaterials.” Int. J. Solids Struct., 47(22–23), 3166–3185.
Gray, D. H., and Al-Refeai, T. (1986). “Behavior of fabric- versus fiber-reinforced sand.” J. Geotech. Eng., 112(8), 804–820.
Gray, D. H., and Ohashi, H. (1983). “Mechanics of fiber reinforcement in sands.” J. Geotech. Engrg., 109(3), 335–353.
Gray, D. H. and Sotir, B. (1995). “Biotechnical stabilization of steepened slopes.” Transportation Research Record 1474, Transportation Research Board, Washington, DC, 23–29.
Gregory, G. H., and Chill, D. S. (1998). “Stabilization of earth slopes with fiber-reinforcement.” Proc., 6th Int. Conf. on Geosynthetics, Industrial Fabrics Association International, Atlanta, 1073–1078.
Gutierrez, M., and Ishihara, K. (2000). “Non-coaxiality and energy dissipation in granular material.” Soils Found., 40(2), 49–59.
Heineck, K. S., and Consoli, N. C. (2004). “Discussion of ‘Discrete framework for limit equilibrium analysis of fibre-reinforced soil’ by J. G. Zornberg.” Geotechnique, 54(1), 72–73.
Heineck, K. S., Coop, M. R., and Consoli, N. C. (2005). “Effect of microreinforcement of soils from very small to large shear strains.” J. Geotech. Geoenviron. Eng., 131(8), 1024–1033.
Hwang, J., Dewoolkar, M., and Ko, H.-Y. (2002). “Stability analysis of two-dimensional excavated slopes considering strength anisotropy.” Can. Geotech. J., 39(5), 1026–1038.
Ibraim, E., Diambra, A., Muir Wood, D., and Russell, A. R. (2010). “Static liquefaction of fibre reinforced sand under monotonic loading.” Geotext. Geomembr., 28(4), 374–385.
Jewell, R. A., and Wroth, C. P. (1987). “Direct shear tests on reinforced sand.” Geotechnique, 37(1), 53–68.
Kaniraj, S. R., and Havanagi, V. G. (2001). “Behavior of cement-stabilized fiber-reinforced fly ash-soil mixtures.” J. Geotech. Geoenviron. Eng., 127(7), 574–584.
Kim, Y. T., Kim, H. J., and Lee, G. H. (2008). “Mechanical behavior of lightweight soil reinforced with waste fishing net.” Geotext. Geomembr., 26(6), 512–518.
Kirkgard, M. M., and Lade, P. V. (1993). “Anisotropic three-dimensional behavior of a normally consolidated clay.” Can. Geotech. J., 30(5), 848–858.
Li, C. (2005). “Mechanical response of fiber-reinforced soil.” Ph.D. thesis, Univ. of Texas–Austin, Austin, TX.
Li, X. S., and Dafalias, Y. F. (2002). “Constitutive modelling of inherently anisotropic sand behavior.” J. Geotech. Geoenviron. Eng., 128(10), 868–880.
Liu, C.-N., Zornberg, J. G., Chen, T.-C., Ho, Y.-H., and Lin, B.-H. (2009). “Behavior of geogrid-sand interface in direct shear mode.” J. Geotech. Geoenviron. Eng., 135(12), 1863–1871.
Liu, J., Wang, G., Kamai, T., Zhang, F., Yang, J., and Shi, B. (2011). “Static liquefaction behavior of saturated fiber-reinforced sand in undrained ring-shear tests.” Geotext. Geomembr., 29(5), 462–471.
Maher, M. H., and Gray, D. H. (1990). “Static response of sand reinforced with fibres.” J. Geotech. Eng., 116(11), 1661–1677.
Michalowski, R. L. (1996). “Micromechanics-based failure model of granular/particulate medium with reinforcing fibers.” Technical Rep., Air Force Office of Scientific Research, Washington, DC.
Micha1owski, R. L. (2008). “Limit analysis with anisotropic fibre-reinforced soil.” Geotechnique, 58(6), 489–501.
Micha1owski, R. L., and Čermák, J. (2002). “Strength anisotropy of fiber-reinforced sand.” Comput. Geotech., 29(4), 279–299.
Micha1owski, R. L., and Čermák, J. (2003). “Triaxial compression of sand reinforced with fibers.” J. Geotech. Geoenviron. Eng., 129(2), 125–136.
Michalowski, R. L., and Zhao, A. (1996). “Failure of fiber-reinforced granular soils.” J. Geotech. Eng., 122(3), 226–234.
Oda, M., Nemat-Nasser, S., and Konishi, J. (1985). “Stress-induced anisotropy in granular materials.” Soils Found., 25(3), 85–97.
Palmeira, E. M., and Milligan, G. W. E. (1989). “Large scale direct shear tests on reinforced soil.” Soils Found., 29(1), 18–30.
Park, S.-S. (2011). “Unconfined compressive strength and ductility of fiber-reinforced cemented sand.” Constr. Build. Mater., 25(2), 1134–1138.
Ranjan, G., Vasan, R. M., and Charan, H. D. (1996). “Probabilistic analysis of randomly distributed fiber-reinforced soil.” J. Geotech. Engrg., 122(6), 419–426.
Sadek, S., Najjar, S. S., and Freiha, F. (2010). “Shear strength of fiber-reinforced sands.” J. Geotech. Geoenviron. Eng., 136(3), 490–499.
Santoni, R. L., and Webster, S. L. (2001). “Airfields and road construction using fiber stabilization of sands.” J. Transp. Eng., 127(2), 96–104.
Sheng, D., Sloan, S. W., and Yu, H. S. (2000). “Aspects of finite element implementation of critical state models.” Comput. Mech., 26(2), 185–196.
Shogaki, T., and Kumagai, N. (2008). “A slope stability analysis considering undrained strength anisotropy of natural clay deposits.” Soils Found., 48(6), 805–819.
Silva Dos Santos, A. P., Consoli, N. C., and Baudet, B. A. (2010). “The mechanics of fibre-reinforced sand.” Geotechnique, 61(10), 791–799.
Sivakumar Babu, G. L., Vasudevan, A. K., and Haldar, S. (2008). “Numerical simulation of fiber-reinforced sand behaviour.” Geotext. Geomembr., 26(2), 181–188.
Sonnenberg, R., Bransby, M. F., Hallett, P. D., Bengough, A. G., Mickovski, S. B., and Davies, M. C. R. (2010). “Centrifuge modelling of soil slopes reinforced with vegetation.” Can. Geotech. J., 47(12), 1415–1430.
Tei, K., Taylor, R. N., and Milligan, G. W. E. (1998). “Centrifuge model tests of nailed soil slopes.” Soils Found., 38(2), 165–177.
Uthayakumar, M., and Vaid, Y. P. (1998). “Static liquefaction of sands under multiaxial loading.” Can. Geotech. J., 35(2), 273–283.
Wang, J., and Gutierrez, M. (2010). “Discrete element simulations of direct shear specimen scale effects.” Geotechnique, 60(5), 395–409.
Wei, W. B., and Cheng, Y. M. (2010). “Soil nailed slope by strength reduction and limit equilibrium methods.” Comput. Geotech., 37(5), 602–618.
Wu, T. H., Mckinnel, W. P., III, and Swanston, D. N. (1979). “Strength of tree roots and landslides on Prince of Wales Island, Alaska.” Can. Geotech. J., 16(1), 19–33.
Yao, Y. P., Lu, D. C., Zhou, A. N., and Zou, B. (2004). “Generalized non-linear strength theory and transformed stress space.” Sci. China, Ser. E: Technol. Sci., 47(6), 691–709.
Zdravković, L., Potts, D. M., and Hight, D. W. (2002). “The effect of strength anisotropy on the behaviour of embankments on soft ground.” Geotechnique, 52(6), 447–457.
Zornberg, J. G. (2002). “Discrete framework for equilibrium analysis of fibre-reinforced soil.” Geotechnique, 52(8), 593–604.
Zornberg, J. G., Cabral, A. R., and Viratjandr, C. (2004). “Behaviour of tire shred-sand mixtures.” Can. Geotech. J., 41(2), 227–241.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Sep 13, 2011
Accepted: Mar 20, 2012
Published online: Mar 22, 2012
Published in print: Jan 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.