Centrifuge Modeling of Ship Impact Loads on Bridge Pile Foundations
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 137, Issue 4
Abstract
Bridges that cross navigable waterways may be affected by accidental ship impacts. To better characterize ship impact loads on bridge pier structures, a comprehensive centrifuge model test program involving 48 ship impact tests was performed on a pile group and a pile group founded in saturated silty sand. These model tests simulated groups of 2-m-diameter by 31.5-m-long pipe piles. The effects of three factors related to the ship (tonnage, speed, and bow structure) and two factors related to the bridge pier structure (superstructure mass and pile-group size) were investigated through these impact tests. The characteristics of the ship impact load were identified and the mechanism of the ship-bridge collision was analyzed. The test results show that the ship impact load was highly dependent on the ship bow structure and the ship impact speed. The test results were compared with other published data and the AASHTO loads. An empirical equation was suggested to relate the ship impact load to the five influencing factors.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (1991). Guide specification and commentary for vessel collision design of highway bridges, Washington, DC.
AASHTO. (1994). LRFD bridge design specifications and commentary, Washington, DC.
ASTM. (1999). “Standard testing method for wet preparation of soil samples for particle-size analysis and determination of soil constants,” D2217, West Conshohocken, PA.
Bezuijen, A., Schaminee, P. E. L., and Lee, D. M. (2003). “Model tests on ship impact in a revetment performed in a geotechnical centrifuge.” Proc. BGA Int. Conf. on Foundations, Telford, London, 119–128.
Bolton, M. D., and Lau, C. K. (1988). “Scale effects arising from particle size.” Proc., Centrifuge 88: Int. Conf. on Geotechnical Centrifuge Modeling, Balkema, Rotterdam, The Netherlands, 127–131.
Bonab, M. G., Chazelas, J. L., Favraud, C., and Levacher, D. (2002). “Simulation of soil-pile interaction under impact loads.” Physical modeling in geotechnics: ICPMG’02, R. Phillips, P. Guo, and R. Popscu, eds., Taylor and Francis, London, 415–419.
Chu, L. M. (2010). “Centrifuge modeling of vessel impacts on bridge pile foundations.” Ph.D. thesis, Hong Kong Univ. of Science and Technology, Hong Kong.
Civil Engineering Department (CED). (2002). Port works design manual—Part 1: General design considerations for marine works, Hong Kong.
Consolazio, G. R., Cowan, D. R., and McVay, M. C. (2006). Barge impact testing of the St. George Island Causeway Bridge—Final rep.: Physical testing and data interpretation, University of Florida, Gainesville, FL.
Dewoolkar, M. M., Ko, H. Y., Stadler, A. T., and Astaneh, S. M. F. (1999). “A substitute pore fluid for seismic centrifuge modeling.” Geotech. Test. J., 22(3), 196–210.
Endo, H., and Yamada, Y. (2001). “The performance of buffer bow structures against collision.” J. Soc. Nav. Archit. Jpn., 189, 209–217.
Frandsen, A. G. (1983). “Accidents involving bridges.” IABSE colloquium on ship collision with bridges and offshore structures, Copenhagen.
Frandsen, A. G., and Langsoe, H. (1980). “Ship collision problems: I. Great Belt Bridge and II. International enquiry.” IABSE Periodica No. 2.
Fung, W. T. (2001). “Experimental study and centrifuge modeling of loose fill slope.” M.S. thesis, Hong Kong Univ. of Science and Technology, Hong Kong.
Garnier, J., et al. (2007). “Catalogue of scaling laws and similitude questions in geotechnical centrifuge modeling.” Int. J. Phys. Model. Geotech., 7(3), 1–24.
Gonzalez, L., Abdoun, T., and Dobry, R. (2006). “Physical modeling and visualization of pile response to lateral spreading.” 6th Int. Conf. on Physical Modeling in Geotechnics, C. W. W. Ng, L. M. Zhang, and Y. H. Wang, eds., Taylor and Francis, London, 921–926.
Grundhoff, T., and Laue, J. (1998). “Investigations of vertical piles under horizontal impact.” Centrifuge 98, Balkema, London, 569–574.
Knott, M. A., and Bonyun, D. (1983). “Ship collision against the Sunshine Skyway Bridge.” IABSE Colloquium on Ship Collision with Bridges and Offshore Structures, Copenhagen, Denmark.
Knott, M. A., and Larsen, O. D. (1990). “Guide specification and commentary for vessel collision design of highway bridges.” Rep. No. FHWA-RD-91-006, U.S. Department of Transportation, Federal Highway Administration, Washington, DC.
Ko, H. Y. (1994). “Modeling seismic problems in centrifuges.” Proc., Int. Conf. Centrifuge 94, C. F. Leung, F. H. Lee, and T. S. Tan, eds., Balkema, Rotterdam, The Netherlands, 3–12.
Kong, L. G., and Zhang, L. M. (2007). “Centrifuge modeling of torsionally loaded pile groups.” J. Geotech. Geoenviron. Eng., 133(11), 1374–1384.
Larsen, O. D. (1993). “Ship collision with bridges: The interaction between vessel traffic and bridge structures.” IABSE Structural Engineering Document 4, Zurich, Switzerland.
McVay, M., Zhang, L. M., Molint, T., and Lai, P. (1998). “Centrifuge testing of large laterally loaded pile groups in sands.” J. Geotech. Geoenviron. Eng., 124(10), 1016–1026.
Modjeski and Masters, Consulting Engineers. (1985). “Criteria for the design of bridge piers with respect to vessel collision in Louisiana waterways.” Louisiana Department of Transportation and the Federal Highway Administration, New Orleans.
Ng, C. W. W., Li, X. S., Van Laak, P. A., and Hou, D. Y. J. (2004). “Centrifuge modeling of loose fill embankment subjected to uniaxial and biaxial earthquakes.” Soil Dyn. Earthquake Eng., 24, 305–318.
Nordic Road Engineering Federation. (1980). “Load regulations for road bridges.” NVF, Rep. No. 4, Magdalena Green, Sweden.
Nunez, I. L. (1988). “Driving and tension loading of piles in sand on a centrifuge.” Proc., Int. Conf. Centrifuge 88, J. F. Corte, ed., Balkema, London, 353–362.
Pedersen, P. T., Valsgard, S., Olsen, D., and Spangenberg, S. (1993). “Ship impacts-bow collisions.” 3rd Int. Symposium on Structural Crashworthiness and Failure, Liverpool, UK.
Remaud, D. (1999). “Pieux sous charges laterals: Etude experimentale de I’effet de groupe.” Ph.D. thesis, Universite de Nantes, Nantes, France.
Schofield, A. N. (1980). “Cambridge geotechnical centrifuge operations.” Geotechnique, 20(1), 227–268.
Shen, C. K., Li, X. S., Ng, C. W. W., and Van Laak, P. A. (1998). “Development of a geotechnical centrifuge in Hong Kong.” Proc., Int. Conf. Centrifuge 98, Tokyo,Kimura, Kusakabe, and Takemure, eds., Balkema, Rotterdam, The Netherlands, 13–18.
Teyssandier, et al. (1987). “Impact protection from ships in the Euroroute project.” IABSE Symp. on Concrete Structures for the Future, International Association for Bridge and Structural Engineering, Paris-Versailles.
Wang, T. L., and Liu, C. H. (1999). “Synthesizing commercial shipping (barge/tug trains) from available data for vessel collision design.” Final Rep.: FL/DOT/RMC/0841-489, Florida Department of Transportation, FL.
Wilson, D. W., Boulanger, R. W., and Kutter, B. L. (2000). “Observed seismic lateral resistance of liquefying sand.” J. Geotech. Geoenviron. Eng., 126(10), 898–906.
Woisin, G. (1976). “The collision tests of the GKSS.” Jahrbuch der Schiffbautechnishen Gesellshaft, 70, 465–487.
Yet, N. S., Leung, C. F., and Lee, F. H. (1994). “Behavior of axially loaded piles in sand.” Proc., Int. Conf. Centrifuge 94, C. F. Leung, F. H. Lee, and T. S. Tan, eds., Balkema, Rotterdam, The Netherlands, 461–466.
Zhang, L. M., McVay, M. C., Gardner, R., Han, S. J., and Lai, P. (2002). “Effects of dead loads on the lateral response of battered pile groups.” Can. Geotech. J., 39(3), 561–575.
Zhang, L. M., McVay, M. C., and Lai, P. (1998). “Centrifuge testing of vertically loaded battered pile groups in sand.” Geotech. Test. J., 21(4), 281–288.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Nov 28, 2008
Accepted: Sep 15, 2010
Published online: Sep 18, 2010
Published in print: Apr 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.