Dilatancy and Shear Strength of Sand at Low Confining Pressures
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 136, Issue 3
Abstract
Sand dilates with shearing at a rate that increases with increasing relative density and decreases with increasing effective confining stress . The peak friction angle of a sand depends on its critical-state friction angle and on dilatancy. In this paper, we develop a simple correlation between peak friction angle, critical-state friction angle, and dilatancy based on triaxial compression and plane-strain compression test data for sand for a range of confining pressures from very low levels to approximately 196 kPa.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alshibli, K. A., and Williams, H. S. (2005). “A true triaxial apparatus for soil testing with mixed boundary conditions.” Geotech. Test. J., 28(6), 534–543.
Been, K., and Jefferies, M. G. (1985). “A state parameter for sands.” Geotechnique, 35(2), 99–112.
Been, K., and Jefferies, M. G. (1986). “A state parameter for sands: Reply to discussion.” Geotechnique, 36(1), 123–132.
Bolton, M. D. (1986). “Strength and dilatancy of sands.” Geotechnique, 36(1), 65–78.
De Josselin de Jong, G. (1976). “Rowe’s stress-dilatancy relation based on friction.” Geotechnique, 26(3), 527–534.
Fukushima, S., and Tatsuoka, F. (1984). “Strength and deformation characteristics of saturated sand at extremely low pressures.” Soils Found., 24(4), 30–48.
Lam, W. -K., and Tatsuoka, F. (1988). “Effects of initial anisotropic fabric and on strength and deformation characteristics of sand.” Soils Found., 28(1), 89–106.
Li, X. S. (2002). “A sand model with state-dependent dilatancy.” Geotechnique, 52(3), 173–186.
Li, X. S., and Dafalias, Y. F. (2000). “Dilatancy for cohesionless soils.” Geotechnique, 50(4), 449–460.
Li, X. -S., Dafalias, Y. F., and Wang, Z. -L. (1999). “State-dependent dilatancy in critical-state constitutive modelling of sand.” Can. Geotech. J., 36(4), 599–611.
Manzari, M. T., and Dafalias, Y. F. (1997). “A critical state two-surface plasticity model for sands.” Geotechnique, 47(2), 255–272.
Matsuoka, H., and Nakai, T. (1982). “A new failure criterion for soils in three-dimensional stresses.” Proc., IUTAM Conf. on Deformation and Failure of Granular Materials, P. A. Vermeer and H. J. Luger, eds., Rotterdam, Balkema, 253–263.
Pradhan, T. B. S., Tatsuoka, F., and Horii, N. (1988). “Strength and deformation characteristics of sand in torsional simple shear.” Soils Found., 28(3), 131–148.
Reades, D. W., and Green, G. E. (1976). “Independent stress control and triaxial extension tests on sand.” Geotechnique, 26(4), 551–576.
Rowe, P. W. (1962). “The stress-dilatancy relation for static equilibrium of an assembly of particles in contact.” Proc. R. Soc. London, 269, 500–527.
Sladen, J. A., D’Hollander, R. D. D., and Krahn, J. (1985). “The liquefaction of sands, a collapse surface approach.” Can. Geotech. J., 22(4), 564–578.
Sladen, J. A., and Oswell, J. M. (1989). “The behavior of very loose sand in the triaxial compression test.” Can. Geotech. J., 26(1), 103–113.
Sutherland, H. B., and Mesdary, M. S. (1969). “The influence of the intermediate principal stress on the strength of sand.” Proc., 7th ICSMFE, Vol. 1, Mexico, 391–399.
Tatsuoka, F. (1987). “Discussion on ‘The strength and dilatancy of sands’ by Bolton, 1986.” Geotechnique, 37(2), 219–226.
Tatsuoka, F., Goto, S., and Sakamoto, M. (1986). “Effects of some factors on strength and deformation characteristics of sand at low pressures.” Soils Found., 26(1), 105–114.
Verdugo, R., and Ishihara, K. (1996). “The steady state of sandy soils.” Soils Found., 36(2), 81–91.
Wang, Q., and Lade, P. V. (2001). “Shear banding in true triaxial tests and its effect on failure in sand.” J. Eng. Mech., 127(8), 754–761.
Wang, Z. -L., Dafalias, Y. F., Li, X. -S., and Makdisi, F. I. (2002). “State pressure index for modeling sand behavior.” J. Geotech. Geoenviron. Eng., 128(6), 511–519.
Wroth, C. P., and Bassett, N. (1965). “A stress-strain relationship for the shearing behavior of sand.” Geotechnique, 15(1), 32–56.
Yang, J., and Li, X. S. (2004). “State-dependent strength of sands from the perspective of unified modeling.” J. Geotech. Geoenviron. Eng., 130(2), 186–198.
Yoshimine, M. (2005). “Archives–Soil mechanics laboratory.” Tokyo Metropolitan University, ⟨http://geot.civil.metro-u.ac.jp/archives/index.html⟩ (Apr. 7, 2005).
Yu, H. S. (1998). “CASM: A unified state parameter model for clay and sand.” Int. J. Numer. Analyt. Meth. Geomech., 22(8), 621–653.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Apr 20, 2007
Accepted: Oct 22, 2007
Published online: Feb 12, 2010
Published in print: Mar 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.