Sensor-Enabled Geosynthetics: Use of Conducting Carbon Networks as Geosynthetic Sensors
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 135, Issue 7
Abstract
A novel technique is developed based on the piezoresistivity of electrically filled polymers to measure the tensile strain in modified geosynthetics without the need for conventional instrumentation (e.g., strain gauges). This paper reports the development of the technique and the results obtained on high-density polyethylene and polypropylene (PP) geogrid specimens filled with carbon black and carbon nanotubes (NTs). It was found that except for NT-filled PP specimens all other composites exhibited significant strain sensitivity in their conductivity. The proof-of-concept study reported in this paper has two important features: (1) strain sensitivity of electrical conductivity was demonstrated in polyolefins used to manufacture geosynthetics; and (2) this strain sensitivity was obtained and demonstrated over the range of strain values that are important in geosynthetic engineering applications.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers wish to acknowledge the cross-disciplinary seed funding awarded by the College of Engineering at the University of Oklahoma to support the research described in this paper. Generous donations of polymers by Exxon-Mobil Chemical (Houston) and masterbatches by Hyperion Catalysis (Cambridge, Mass.) and RTP Company (Winona, Minn.) are acknowledged. The assistance of Dr. Preston Larson at the Samuel Roberts Noble Electron Microscopy Laboratory (SRNEML) of the University of Oklahoma in producing scanning electron microscopy (SEM) images and that of Mr. Israel J. Chavez Sumarriva in preparing the SEM samples are gratefully acknowledged.
References
AASHTO. (2002). Standard specifications for highway bridges, 17th Ed., Washington, D.C.
Abu-Farsakh, M. Y., Almohd, I., and Farrag, K. (2006). “A comparison of field and laboratory pullout tests on geosynthetics in marginal soils.” Transportation Research Record. 1975, Transportation Research Board, Washington, D.C., 124–136.
Abu-Hejleh, N., Wang, T., and Zornberg, J. (2000). “Performance of geosynthetic-reinforced walls supporting bridge and approaching roadway structures.” Advances in transportation and geoenvironmental systems using geosynthetics, J. G. Zornberg and B. R. Christopher, eds., Vol. 103, ASCE, New York, 218–243.
Allen, T. M., and Bathurst, R. J. (2002). “Soil reinforcement loads in geosynthetic walls at working stress conditions.” Geosynthet. Int., 9(5–6), 525–566.
Allen, T. M., Bathurst, R. J., Holtz, R. D., Walters, D. L., and Lee, W. F. (2003). “A new working stress method for prediction of reinforcement loads in geosynthetic walls.” Can. Geotech. J., 40, 976–994.
Allen, T. M., Chrisopher, B. R., and Holtz, R. D. (1992). “Performance of a high geotextile wall in Seattle, Washington. Geosynthetic-reinforced soil retaining walls.” Proc., Int. Symp. on Geosynthetic-Reinforced Soil Retaining Walls, Denver, J. T. H. Wu, ed., Balkema, Rotterdam, The Netherlands, 81–100.
Al-Qadi, I. L., Tutumluer, E., and Dessouky, S. (2006). “Construction and instrumentation of full-scale geogrid-reinforced flexible pavement test sections.” Proc., Airfield and Highway Pavements Specialty Conf., I. L. Al-Qadi, ed., Vol. 191, ASCE, Reston, Va., 12.
Anelli, J. N., Zaikov, G. E., and Khananashvili, L. M. (1999). “Effects of mechanical deformations on the structurization and electricconductivity of electric conducting polymer composites.” J. Appl. Polym. Sci., 74, 601–621.
ASTM. (2007a). “Standard test methods for geosynthetics.” Book of standards, D6637-01, Vol. 04.13, Philadelphia.
ASTM. (2007b). “Standard test method for tensile properties of plastics by use of microtensile specimens.” Book of standards, D1708-06, Vol. 08.01, Philadelphia.
Aydilek, A. H., Huler, M., and Edil, T. B. (2004). “Use of image analysis in determination of strain distribution during geosynthetic tensile testing.” J. Comput. Civ. Eng., 18(1), 65–74.
Bathurst, R. J., Allen, T. M., and Walters, D. L. (2002). “Short-term strain and deformation behavior of geosynthetic walls at working stress conditions.” Geosynthet. Int., 9(5–6), 451–482.
Bathurst, R. J., Vlachopoulos, N., Walters, D. L., Burgess, P. G., and Allen, T. M. (2006). “The influence of facing rigidity on the performance of two geosynthetic reinforced soil retaining walls.” Can. Geotech. J., 43(12), 1225–1237.
Bayer, R. K., et al. (1988). “Conductive PE-carbon composites by elongation flow injection moulding. Part 1: Flow-induced conductivity profile-high molecular weight matrix.” J. Mater. Sci., 23, 475–480.
British Standards Institute (BSI). (1995). “Code of practice for strengthened/reinforced soils and other fills.” BS8006, London.
Cembrola, R. (1982). “The relationship of carbon black dispersion to electrical resistivity and vulcanizate physical properties.” Polym. Eng. Sci., 22, 601–609.
Chung, D. D. L. (1998). “Self-monitoring structural materials.” Mater. Sci. Eng. R., 22(2), 57–78.
Dannenberg, E. M. (1952). “Carbon black dispersion and reinforcement.” Ind. Eng. Chem., 44(4), 813–818.
Das, N. C., Chaki, T. K., and Khastgir, D. (2002). “Effect of axial stretching on electrical resistivity of short carbon fiber and carbon black filled conductive rubber composites.” Polym. Int., 51, 156–163.
Desrues, J., Chambon, R., Mokni, M., and Mazerolle, F. (1996). “Void ratio evolution inside shear bands in triaxial sand specimens studied by computed tomography.” Geotechnique, 46(3), 529–546.
Elias, V., Christopher, B. R., and Berg, R. R. (2001). “Mechanically stabilized earth walls and reinforced soil slopes-design and construction guidelines.” FHWA-NHI-00-043, Federal Highway Administration, Washington, D.C.
EPA. (2007). “Laws and regulations, The Resource Conservation and Recovery Act (RCRA).” ⟨http://www.epa.gov/osw/laws-reg.htm⟩.
Ezquerra, T. A., Bayer, R. K., Zachmann, H. G., and Balta Calleja, F. J. (1988). “Conductive PE-carbon black composites by elongational flow injection moulding. Part 2: Variation of the molecular weight of the matrix.” J. Mater. Sci., 23, 4121–4126.
Farrag, K., and Morvant, M. (2004). “Evaluation of interaction properties of geosynthetics in cohesive soils, Lab and field pullout tests.” Technical Summary Rep. No. 380, LTRC, Baton Rouge, La.
Godovski, D. Y., Koltypin, E. A., Volkov, A. V., and Moskvina, M. A. (1993). “Sensor properties of filled polymer composites.” Analyst (Cambridge, U.K.), 118, 997–999.
Gul, V. E. (1996). Structure and properties of conducting polymer composites (New concepts in polymer science), Brill Academic Publishers, Boston.
Guler, E., Hamderi, M., and Demirkan, M. M. (2007). “Numerical analysis of reinforced soil retaining wall structures with cohesive and granular backfills.” Geosynthet. Int., 14(6), 330–345.
Hatami, K., and Bathurst, R. J. (2005). “Development and verification of a numerical model for the analysis of geosynthetic reinforced-soil segmental walls under working stress conditions.” Can. Geotech. J., 42(4), 1066–1085.
Hatami, K., and Bathurst, R. J. (2006). “A numerical model for reinforced soil segmental walls under surcharge loading.” J. Geotech. Geoenviron. Eng., 132(6), 673–684.
Hatami, K., and Raymond, G. P. (2006). “Influence of soil strength on the optimal embedment depth of a geosynthetic reinforcement layer in granular reinforced foundations.” Transportation Research Record. 1975, Transportation Research Board, Washington, D.C., 155–162.
Helwany, M. B., Wu, J. T. H., and Kitsabunnarat, A. (2007). “Simulating the behavior of GRS bridge abutments.” J. Geotech. Geoenviron. Eng., 133(10), 1229–1240.
Hironaka, J., Hirai, T., Otani, J., and Inoue, M. (2004). “Effect of fines content in soils on pullout mechanism of geogrid.” Proc., GeoAsia 2004, Seoul, Korea, 357–362.
Huang, C.-C. (1994). “Report on three unsuccessful reinforced walls.” Recent case histories of permanent geosynthetic-reinforced soil retaining walls, F. Tatsuoka, and D. Leshchinsky, eds., Balkema, Rotterdam, The Netherlands, 219–221.
Huang, J. C. (2002). “Carbon black filled conducting polymers and polymer blends.” Adv. Polym. Technol., 21(4), 299–313.
Karwa, A. (2006). “Printing studies with conductive inks and exploration of new conducting polymer compositions.” MSc thesis, Rochester Institute of Technology, Rochester, N.Y.
Kato, H., and Miyashita, Y. (1990). “Qualification of the electrical conductivity of carbon black filled polymeric materials.” Proc., 1990 IEEE Conf. on Electrical Insulation and Dielectric Phenomena, IEEE, Piscataway, N.J., 417–425.
Keithley Instruments Inc. (1972). Instruction manual for the resistivity adapter model 6105, Cleveland.
Ketchart, K., and Wu, J. T. H. (2001). “Performance test for geosynthetic-reinforced soil including effects of preloading.” Rep. No. FHWA-RD-01-018, Univ. of Colorado at Denver, Colo.
Killion/Davis-Standard. (2008). ⟨http:www.saturn2.com/killion.html⟩.
Koerner, J., Soong, T.-Y., and Koerner, R. M. (2001). “Earth retaining wall costs in the USA.” Proc., Geosynthetics 2001, Portland, Ore., 483–508.
Koerner, R. (2005). Designing with geosynthetics, 5th Ed., Prentice-Hall, Upper Saddle River, N.J.
Ling, H. I., and Leshchinsky, D. (2003). “Finite element parametric study of the behavior of segmental block reinforced-soil retaining walls.” Geosynthet. Int., 10(3), 77–94.
Ling, H. I., Leshchinsky, D., and Chou, N. N. S. (2001). “Post-earthquake investigation on several geosynthetic-reinforced soil retaining walls and slopes during the Ji-Ji earthquake of Taiwan.” Soil Dyn. Earthquake Eng., 21(4), 297–313.
Luna, R. (1999). “Digital image analysis techniques for fiber and soil mixtures.” LTRC Project No. 98-2TIRE, Rep. Submitted to the Louisiana Transportation Research Center, Dept. of Civil and Environmental Engineering, Tulane Univ., New Orleans.
Lux, F. (1993). “Models proposed to explain the electrical conductivity of mixtures made of conductive and insulating materials.” J. Mater. Sci., 28, 285–301.
Ma, C. C., and Wu, J. T. H. (2004). “Field performance of an independent full-height facing reinforced soil wall.” J. Perform. Constr. Facil., 18(3), 165–172.
Marr, W. A. (2008). “Why performance monitoring?” GeoAmericas 2008, Proc., 1st Pan American Geosynthetics Conf. and Exhibition, Cancun, Mexico, IFAI, Roseville, Minn., Paper No. 1240, 690–704.
Martizen Salazar, J., Bayer, R. K., Ezquerra, T. A., and Balta Calleja, F. J. (1989). “Conductive polyethylene-carbon black composites by elongational-flow injection molding. Part 3: Study of the structure and morphology.” Colloid Polym. Sci., 267, 409–413.
Miyata, Y., and Bathurst, R. J. (2007). “Development of K-stiffness method for geosynthetic reinforced soil walls constructed with soils.” Can. Geotech. J., 44(12), 1391–1416.
Nancey, A., Lacina, B., and Henderson, J. (2007). “Geotextile and optic fibers: Feedback after four years of use in soil.” Geosynthetics 2007: Proc., GRI-20, Washington, D.C., IFAI, Roseville, Minn.
National Concrete Masonry Association (NCMA). (2002). Design manual for segmental retaining walls, 2nd Ed., Herndon, Va.
Pamukcu, S., and Turel, M. (2007). “Use of BOTDR to measure distributed strains of geosynthetics.” Geosynthetics 2007: Proc., GRI-20, Washington, D.C.
Paylor, M. R., Christopher, B. R., and Nyren, R. R. (2008). “Intelligent geosynthetics used for performance monitoring and construction control, Woodrow Wilson Bridge—Maryland portion.” Proc., GeoAmericas 2008, 1st Pan American Geosynthetics Conf. and Exhibition, Cancun, Mexico, 744–753.
Pinto, G., Cipriano, L. G., and Ana, J. M. (1999). “Polymer composites prepared by compression molding of a mixture of carbon black and nylon 6 powder.” Polym. Compos., 20, 804–808.
Pramanik, P. K., Khastagir, D., and Saha, T. N. (1993). “Effect of extensional strain on the resistivity of electrically conductive nitrile-rubber composites filled with carbon filler.” J. Mater. Sci., 28, 3539–3546.
Rechenmacher, A. (2003). “Imaging-based experimental soil mechanics.” Geomechanics, Testing, Modeling, and Simulation, Proc., 1st Japan—U.S. Workshop on Testing, Modeling, and Simulation, J. A. Yamamuro and J. Koseki eds., Geotechnical Special Publication No. 143, ASCE, New York, 653–663.
RTP Co. (2004). ⟨http://www.rtpcompany.com/info/data/es/ESDC700.htm⟩.
RTP Co. (2006). ⟨http://www.rtpcompany.com/info/data/esd/ESDC100.htm⟩.
Samuel Roberts Noble Electron Microscopy Laboratory (SRNEML). (2008). Univ. of Oklahoma, Norman, Okla., ⟨http://www.microscopy.ou.edu/jsm-880.shtml⟩.
Strumpler, R., and Glatz-Reichenbach, J. (1999). “Conducting polymer composites.” J. Electroceram., 3(4), 329–346.
Stulgis, R. P. (2005). “Full-scale MSE test walls.” Proc., NAGS 2005/GRI-19 Conf., Las Vegas, IFAI, Roseville, Minn.
Walters, D. L., Allen, T. M., and Bathurst, R. J. (2002). “Conversion of geosynthetic strain to load using reinforcement stiffness.” Geosynthet. Int., 9(5–6), 483–523.
Warren, K. A., Howard, I. L., and Brooks, J. A. (2006). “Use of digital photography to analyze foil strain gages on geosynthetics.” Proc., GeoCongress 2006, Vol. 187, 282, ASCE, Reston, Va., 1–6.
Yacubowicz, J., Narkis, M., and Benguigui, L. (1990). “Electrical and dielectric properties of segregated carbon black-polyethylene systems.” Polym. Eng. Sci., 30, 459–468.
Zheng, Q., Zhou, J. F., and Song, Y. H. (2004). “Time-dependent uniaxial piezoresistive behavior of high-density polyethylene/short carbon fiber conductive composites.” J. Mater. Res., 19(9), 2625–2634.
Zhu, S., Zheng, Q., Zhou, J. F., and Zhang, M. Q. (2006). “Relationship between uniaxial deformation and piezoresistance for HDPE/CB composites.” Acta Polymerica Sinica, 1, 82–86.
Zois, H., Apekis, L., and Omastova, M. (1999). “Electrical properties and percolation phenomena in carbon black filled polymer composites.” Proc., 10th Int. Symp. on Electrets, IEEE, New York, 529–532.
Zornberg, J. G., and Arriaga, F. (2003). “Strain distribution within geosynthetic-reinforced slopes.” J. Geotech. Geoenviron. Eng., 129(1), 32–45.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Jan 23, 2008
Accepted: Nov 9, 2008
Published online: Jun 15, 2009
Published in print: Jul 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.