Reliability Analysis of Partial Safety Factor Design Method for Cantilever Retaining Walls in Granular Soils
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 135, Issue 5
Abstract
Uncertainties in the geotechnical design variables and design equations have a significant impact on the safety of cantilever retaining walls. Traditionally, uncertainties in the geotechnical design are addressed by incorporating a conservative factor of safety in the analytical model. In this paper, a risk-based approach is adopted to assess the influence of the geotechnical variable and design equation uncertainties on the design of cantilever retaining walls in sand using the “partial factor of safety on shear strength” approach. A random model factor based on large-scale laboratory test data from the literature has been incorporated into the reliability analyses to quantify the uncertainty in the geotechnical calculation model. Analyses conducted using Monte Carlo simulation show that the same partial factor can have very different levels of risk depending on the degree of uncertainty of the mean value of the soil friction angle. Calibration studies show the partial factor necessary to achieve target probability values of 1 and 0.1%.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ang, A. H. S., and Tang, W. H. (1984). Probability concepts in engineering planning and design. Decision, risk and reliability, Vol. 2, Wiley, New York.
Babu, G. L. S., and Basha, B. M. (2007). “Optimum design of cantilever sheet pile walls in sandy soils using inverse reliability approach.” Comput. Geotech., in press.
Baecher, G. B., and Christian, J. T. (2003). Reliability and statistics in geotechnical engineering, Wiley, New York.
Basma, A. A. (1991). “Reliability-based design of sheet pile structures.” Reliab. Eng. Syst. Saf., 33, 215–230.
Bica, A. V. D., and Clayton, C. R. I. (1992). “The preliminary design of free embedded cantilever walls in granular soil.” Proc., Int. Conf. on Retaining Structures, Institute of Civil Engineers, London, 731–740.
Blum, H. (1931). Einspannungsverhaltnisse bei bohlwerken, Wilh. Ernst und Sohn, Berlin.
Bransby, P. L., and Milligan, G. W. E. (1975). “Soil deformation near cantilever sheet pile walls.” Geotechnique, 25(2), 175–195.
British Standards Institution (BSI). (1994). Code of practice for earth retaining structures, British Standard 8002, London.
Clayton, C. R. I., Militisky, J., and Woods, R. I. (1993). Earth pressure and earth retaining structures, Chapman & Hall, London.
Craig, R. F. (2004). Craig’s soil mechanics, 7th Ed., Spon, Oxford, U.K.
Duncan, J. M. (2000). “Factor of safety and reliability in geotechnical engineering.” J. Geotech. Geoenviron. Eng., 126(4), 307–316.
European Committee for Standardization (CEN). (2004). “Geotechnical design. Part 1: General rules.” Eurocode 7, Brussels, Belgium.
Gaba, A., Simpson, B., Powrie, W., and Beadman, D. R. (2003). “Embedded retaining walls—Guidance for economic design.” CIRIA Rep. No. C580, Construction Industry Research & Information Association, London.
Goh, A. T. C., and Kulhawy, F. H. (2005). “Reliability assessment of serviceability performance of braced retaining walls using a neural network approach.” Int. J. Numer. Analyt. Meth. Geomech., 29(6), 627–642.
King, G. J. W., and McLoughlin, J. P. (1992). “Centrifuge model studies of a cantilever retaining wall in sand.” Proc., Int. Conf. on Retaining Structures, Institute of Civil Engineers, London, 711–721.
Lacasse, S. (1999). “The importance of dealing with uncertainties in foundation analysis.” Proc., 12th European Conf. Soil Mech. & Geotechnical Engineering, Amsterdam, Vol. 1, 385–392.
Lancellotta, R. (1995). Geotechnical engineering, Balkema, Rotterdam, The Netherlands.
Li, K. S., Lee, I. K., and Lo, S. C. R. (1993). “Limit state design in geotechnics.” Proc., Probabilistic Methods in Geotechnical. Engineering, Canberra, Australia, Balkema, Rotterdam, The Netherlands, 29–44.
Lyndon, A., and Pearson, R. A. (1984). “Pressure distribution of a rigid retaining wall in cohesionless material.” Proc., The Application of Centrifuge Modeling to Geotechncial Design, Univ. of Manchester, Manchester, U.K., 272–281.
Matsuoka, H., and Nakai, T. (1982). “A new failure criterion for soils in three dimensional stresses.” Proc., Symp. Deformation Failure of Granular Materials, Int. Union of Theoretical and Applied Mechanics, Delft, The Netherlands, 253–263.
Padfield, C. J., and Mair, R. J. (1984). “Design of retaining walls embedded in stiff clay.” CIRIA Rep. No. 104, Construction Industry Research and Information Association, London.
Phoon, K. K., and Kulhawy, F. H. (1999). “Characterization of geotechnical variability.” Can. Geotech. J., 36(4), 612–624.
Phoon, K. K., and Kulhawy, F. H. (2003). “Evaluation of model uncertainties for reliability-based foundation design.” Proc., 9th Int. Conf. Advances of Statistics and Probability in Civil Engineering, Vol. 2, Millpress, Rotterdam, The Netherlands, 1351–1356.
Phoon, K. K., Kulhawy, F. H., and Grigoriu, M. D. (1995). “Reliability-based design of foundations for transmission line structures.” Rep. No. TR-105000, EPRI, Palo Alto, Calif.
Phoon, K. K., Liu, S. L., and Chow, Y. K. (2003). “Estimation of model uncertainties for reliability-based design of cantilever walls in sand.” Proc., Int. Workshop on Limit State Design in Geotechncial Engineering Practice, Massachusetts Institute of Technology, Cambridge, Mass., 1–17.
Powrie, W. (2004). Soil mechanics, 2nd Ed., Spon, Oxford, U.K.
Rowe, P. W. (1951). “Cantilever sheet piling in cohesionless soil.” Engineering, Institution of Civil Engineers, London, 316–319.
Shen, R. F., Leung, C. F., and Chow, Y. K. (1998). “Centrifuge modeling of pile response due to excavation-induced soil movement.” Proc., 11th KKNN Seminar on Civil Engineering, Singapore, National Univ. of Singapore, Singapore, 332–337.
Symons, I. F., and Kotera, H. (1987). “A parametric study of the stability of embedded cantilever retaining walls.” Research Rep. No. 116, Transport and Road Research Laboratory, London.
Tang, W. H., Yuceman, M. S., and Ang, A. H. S. (1971). “Reliability analysis and design of braced excavation systems.” Proc., 1st Int. Conf. Applications of Statistics and Probability in Soil & Structural Engineering, Hong Kong, Hong Kong University Press, Hong Kong, 187–202.
Teng, W. C. (1962). Foundation design, Prentice-Hall, Englewood Cliffs, N.J.
United States Steel Corporation (USS). (1974). USS steel sheet piling design manual, Pittsburgh.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 135 • Issue 5 • May 2009
Pages: 616 - 622
Copyright
© 2009 ASCE.
History
Received: Jan 8, 2008
Accepted: Aug 22, 2008
Published online: May 1, 2009
Published in print: May 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.