Pile Bearing Capacity Factors and Soil Crushabiity
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 135, Issue 7
Abstract
The existence of large magnitude stresses at the tip of a bearing pile is a well known phenomenon leading to crushing of soil grains and thus affecting pile behavior. Classical foundation design calculations which assume that the soil fails in shear and neglect volume change can be safely used where stress levels or particle strengths prevent crushing, however in the case of weak grains or high foundation stresses consideration should be given to the effects of grain crushing and the resulting volumetric compression. Model pile tests have been carried out in two skeletal carbonate sands and a standard silica sand with the aim of examining the variation of skin friction and end bearing capacities with degree of penetration. The mobilization of the strength of crushable soils requires a much higher strain level while at the same time the end bearing pressure on the model piles exceeded inducing considerable particle breakage. The peak skin friction for all sands occurred at a settlement normalized by pile diameter, , of less than 0.1. At this point the carbonate sands generally had lower skin friction values than the silica sand. Further displacement caused a rapid decrease in skin friction for all three materials. At higher lateral stresses the less crushable Toyoura silica sand generated higher skin frictions. Samples of Chiibishi sand were sectioned and photographed. It was observed that a spherical plastic zone was formed at the base of the pile which expanded with increasing and a degraded layer of broken particles developed around the pile as increased. Large values of the Marsal particle breakage factor were restricted to a zone extending outwards to one pile radius. An end bearing capacity modification factor has been proposed to adapt the conventional bearing capacity equation for soil crushability. This modification factor is a function of soil compressibility and degree of penetration. The factor was shown to decrease with increasing soil compressibility and increase with normalized penetration .
Get full access to this article
View all available purchase options and get full access to this article.
References
Airey, D. W., and Fahey, M. (1991). “Cyclic response of calcareous soil from the North-West Shelf of Australia.” Geotechnique, 41(1), 101–122.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Geotechnique, 36(1), 65–78.
Bopp, P. A., and Lade, P. V. (1997). “Effect of initial density on soil instability at high pressure.” Proc. ASCE, 123(GT7), 671–677.
Coop, M. R. (1990). “The mechanics of uncemented carbonate sands.” Geotechnique, 40(4), 607–626.
Coop, M. R., Sorenesen, K. K., Bodas Freitas, T., and Georgoutos, G. (2004). “Particle breakage during shearing of a carbonate sand.” Geotechnique, 54(3), 157–163.
Garnier, J., Gaudin, C., Springman, S. M., Culligan P. J., Goodings, D., Konig, D., Kutter, B., Phillips, R., Randolph, M. F., and Thorel, L. (2007). “Catalogue of scaling laws and similitude questions in geotechnical centrifuge modelling.” Int. J. Phys. Modell. Geotech., 7(3), 1–24.
Golightly, C. R. (1989). “Engineering properties of carbonate sands.” Ph.D. thesis, University of Bradford, Bradford, U.K.
Golightly, C. R., and Hyde, A. F. L. (1988). “Some fundamental properties of carbonate sands.” Proc., Int. Conf. on Calcareous Sediments, Vol. 1, Perth, Australia, 173–184.
Hardin, B. O. (1985). “Crushing of soil particles.” J. Geotech. Engrg., 111(10), 1177–1192.
Hyde, A. F. L. (1994). “The modelling of crushable soils.” Proc., Int. Symp. on Pre-Failure Deformation Characteristics of Geo-materials, Vol. 2, Japanese Society of Soil Mechanics and Foundation Engineering, IS Hokkaido, Japan, 1201–1202.
Hyodo, M., Aramaki, N., Itoh, M., and Hyde, A. F. L. (1996). “Cyclic strength and deformation of crushable carbonate sand.” Soil Dyn. Earthquake Eng., 15(5), 331–336.
Hyodo, M., Hyde, A. F. L., and Aramaki, N. (1998). “Liquefaction of crushable soils.” Geotechnique, 48(4), 527–543.
Hyodo, M., Hyde, A. F. L., Aramaki, N., and Nakata, N. (2002). “Undrained monotonic and cyclic shear behaviour of sand under low and high confining stresses.” Soils Found., 42(3), 63–76.
Lehane, B. M., Gaudin, C., and Schneider, J. A. (2005). “Scale effects on tension capacity for rough piles buried in dense sand.” Geotechnique, 55(10), 709–719.
Marsal, R. J. (1965). “Soil properties—Shear strength and consolidation.” Proc., 6th Int. Conf. on Soil Mechanics and Foundation Engineering, Montreal, Vol. 3, The University Press, Toronto, 310–316.
McDowell, G. R., and Bolton, M. D. (1998). “On micromechanics of crushable aggregates.” Geotechnique, 48(5), 667–679.
McDowell, G. R., and Daniell, C. M. (2001). “Fractal compression of soil.” Geotechnique, 51(2), 173–176.
McDowell, G. R., and Harireche, O. (2002). “Discrete element modelling of yielding and normal compression of sand.” Geotechnique, 52(4), 299–304.
Meyerhof, G. G. (1976). “Bearing capacity and settlement of pile foundations.” Proc. ASCE, 102(GT3), 197–228.
Miura, N., and O-hara, S. (1979). “Particle crushing of a decomposed granite soil under shear stress.” Soils Found., 19(3), 1–14.
Nakata, Y., Hyde, A. F. L., Hyodo, M., and Murata, H. (1999). “A probabilistic approach to sand crushing in the triaxial test.” Geotechnique, 49(5), 567–583.
Nakata, Y., Hyodo, M., Hyde, A. F. L., Kato, Y., and Murata, H. (2001a). “Microscopic particle crushing of sand subjected to high pressure one dimensional compression.” Soils Found., 41(1), 69–82.
Nakata, Y., Kato, Y., Hyodo, M., Hyde, A. F. L., and Murata, H. (2001b). “One dimensional compression behaviour of uniformly graded sand related to single particle crushing strength.” Soils Found., 41(2), 39–51.
Reissner, H. (1924). “Zum erddruckproblem.” Proc., 1st Int. Congress for Applied Mechanics, Delft, The Netherlands, C. B. Biezeno and J. M. Burgers, eds., Technische Boekandel en Drukkerij J. Waltman Jr., Delft, 295–311.
Tanaka, K., Yasufuku, N., Murata, H., and Hyodo, M. (1995). “Engineering properties of carbonate sands and skin friction of pile in sands.” Proc., Japan Society of Civil Engineers, Japan Society of Civil Engineers, Tokyo, No. 523/III-32, 99–109 (in Japanese).
Tarantino, A., and Hyde, A. F. L. (2005). “An experimental investigation of work dissipation in crushable materials.” Geotechnique, 55(8), 575–584.
White, D. J., and Bolton, M. D. (2004). “Displacement and strain paths during plain-strain model pile installation in sand.” Geotechnique, 54(6), 375–397.
Yasufuku, N., and Hyde, A. F. L. (1995). “Pile end-bearing capacity in crushable sands.” Geotechnique, 45(4), 663–676.
Yasufuku, N., Tanaka, K., Murata, H., and Hyodo, M. (1994). “End bearing capacity of pile in highly compressible sands and its evaluation.” Proc., Japan Society of Civil Engineers, Japan Society of Civil Engineer, Tokyo, No. 505/III-29, 191–200 (in Japanese).
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Oct 22, 2007
Accepted: Nov 6, 2008
Published online: Feb 21, 2009
Published in print: Jul 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.