Soil Arching in Dry Sand: Numerical Simulations Using Double-Slip Plasticity Gradient Model
Publication: International Journal of Geomechanics
Volume 22, Issue 2
Abstract
The arching phenomenon is intrinsic to granular materials and is a manifestation of the effects of their discrete microstructure. The fundamental mechanism of arching is the ability of discrete granular particles to transfer loads through force chains. Its effects are reflected through changes in the amount of stresses experienced by underground structures. Recent experiments and discrete element simulations have shown that stress distributions evolve, and different arching patterns form depending on the microstructure. While such studies can highlight the important effects of microstructures on soil arching, their use in developing solutions to arching in the field is limited. This study uses a double-slip gradient model implemented in the ABAQUS finite-element software to account for the microstructural effects and simulates the effects of arching in dry sand. The model assumes plastic deformation in granular materials to consist of dilatant shearing along two active planes. Furthermore, this model uses a gradient term of effective plastic strain that directly incorporates the effects of the material length scale. Numerical simulations were conducted to model the classic trap-door problem. It is found that strains begin to localize and form rupture bands during deformation. Furthermore, the pattern of localization of plastic strains is observed to be dependent on the orientation of the initial slip system. While arching effects were observed to initiate early with trap-door movement, its maximum effect is only realized after full localization. The variation of normalized vertical stress is found to be near linear and reaches a maximum value around a normalized height of 0.8 above the trap-door irrespective of the orientation of the initial slip system. On the other hand, the maximum value of the stress and the value of its reduction is dependent on both the displacement of the trap-door and the initial slip system orientation. It is shown that such a reduction in stresses cannot be predicted by the current analytical formulations, as they do not account for the effects of the microstructure or the amount of displacement.
Get full access to this article
View all available purchase options and get full access to this article.
References
Al Hattamleh, O., B. Muhunthan, and H. M. Zbib. 2005a. “Stress distribution in granular heaps using multi-slip formulation.” Int. J. Numer. Anal. Methods Geomech. 29 (7): 713–727. https://doi.org/10.1002/nag.435.
Al Hattamleh, O., B. Muhunthan, and F. Shalabi. 2009. “Numerical simulation of fabric anisotropy and strain localization of sand under simple shear.” Int. J. Numer. Anal. Methods Geomech. 33 (9): 1255–1275. https://doi.org/10.1002/nag.768.
Al Hattamleh, O., B. Muhunthan, and H. M. Zbib. 2004a. “Multi-slip formulation for modeling localization in granular materials.” In Geo Jordan 2004: Advances in geotechnical engineering with emphasis on dams, highway materials, and soil improvement, edited by K. Alshibli, A. I. H. Malkawi, and M. Alsaleh, 200–213. Irbid, Jordan: ASCE, Geotechnical Practical Publication.
Al Hattamleh, O., B. Muhunthan, and H. M. Zbib. 2004b. “Gradient plasticity modelling of strain localization in granular materials.” Int. J. Numer. Anal. Methods Geomech. 28 (6): 465–481. https://doi.org/10.1002/nag.345.
Al Hattamleh, O., B. Muhunthan, and H. M. Zbib. 2005b. “Predictions of stress dip in granular heaps using multi-slip formulation.” In Proc., 5th Int. Conf. on Powders and Grains 2005, edited by R. Garcia-Rojo, H. J. Herrmann, and Sean McNamara. London: CRC Press.
Al Hattamleh, O., B. Muhunthan, and H. M. Zbib. 2007. “Multi-slip gradient formulation for modeling microstructure effects on shear bands in granular materials.” Int. J. Solids Struct. 44 (10): 3393–3410. https://doi.org/10.1016/j.ijsolstr.2006.09.027.
Al Hattamleh, O., and B. Muhunthan. 2021. “Evolution of strain gradient formulation in capturing localization phenomena in granular materials.” J. Eng. Mater. Technol. 144 (1): 011003. https://doi.org/10.1115/1.4051083.
Anand, L., and C. Gu. 2000. “Granular materials: Constitutive equations and strain localization.” J. Mech. Phys. Solids 48 (8): 1701–1733. https://doi.org/10.1016/S0022-5096(99)00066-6.
Balendran, B., and S. Nemat-Nasser. 1993. “Double sliding model for cyclic deformation of granular materials, including dilatancy effects.” J. Mech. Phys. Solids 41 (3): 573–612. https://doi.org/10.1016/0022-5096(93)90049-L.
Bendenia, N., M. Zidour, A. A. Bousahla, F. Bourada, A. Tounsi, K. H. Benrahou, E. A. Bedia, S. R. Mahmoud, and A. Tounsi. 2020. “Deflections, stresses and free vibration studies of FG-CNT reinforced sandwich plates resting on Pasternak elastic foundation.” Comput. Concr. 26 (3): 213–226.
Bi, Z., Q. Gong, P. Guo, and Q. Cheng. 2020. “Experimental study of the evolution of soil arching effect under cyclic loading based on trapdoor test and particle image velocimetry.” Can. Geotech. J. 57 (6): 903–920. https://doi.org/10.1139/cgj-2019-0205.
Bierbaumer, A. 1913. Die Dimensionierung des Tunnelmauerwerkes: Studien. Leipzig, Germany: Wilhelm Engelmann.
Bourada, F., A. A. Bousahla, A. Tounsi, E. A. Bedia, S. R. Mahmoud, K. H. Benrahou, and A. Tounsi. 2020. “Stability and dynamic analyses of SW-CNT reinforced concrete beam resting on elastic-foundation.” Comput. Concr. 25 (6): 485–495.
Cain, W. 1916. Earth pressure, retaining walls and bins. New York: John Wiley & Sons.
Chen, Y., W. Cao, and R. Chen. 2008. “An experimental investigation of soil arching within basal reinforced and unreinforced piled embankments.” Geotext. Geomembr. 26 (2): 164–174. https://doi.org/10.1016/j.geotexmem.2018.12.006.
Chevalier, B., J. Otani, and T. Mukunoki. 2014. “Experimental study of trapdoor problem in 3 dimensions with X-ray CT-transition from plane strain to 3D behavior.” In Proc., 14th Int. Conf. of Int. Association for Computer Methods and Recent Advances in Geomechanics. London: Taylor & Francis Group. https://doi.org/10.1201/b17435-56.
Chevalier, B., G. Combe, and P. Villard. 2012. “Experimental and discrete element modeling studies of the trapdoor problem: Influence of the macro-mechanical frictional parameters.” Acta Geotech. 7 (1): 15–39. https://doi.org/10.1007/s11440-011-0152-5.
Dewoolkar, M. M., K. Santichaianant, and H. Y. Ko. 2007. “Centrifuge modeling of granular soil response over active circular trapdoors.” Soils Found. 47 (5): 931–945. https://doi.org/10.3208/sandf.47.931.
Engesser, F. 1882. “Ueber den Erdduck gegen innere Stützwande (Tunnelwande) (D. Bauzeitung, ed.).” Deutsche Bauzeitung.
Eskişar, T., J. Otani, and J. Hironaka. 2012. “Visualization of soil arching on reinforced embankment with rigid pile foundation using X-ray CT.” Geotext. Geomembr. 32: 44–54. https://doi.org/10.1016/j.geotexmem.2011.12.002.
George, T. I., and S. M. Dasaka. 2021. “Numerical investigation of soil arching in dense sand.” Int. J. Geomech. 21 (5): 04021051. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001971.
Han, J., F. Wang, M. Al-Naddaf, and C. Xu. 2017. “Progressive development of two-dimensional soil arching with displacement.” Int. J. Geomech. 17 (12): 04017112. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001025.
Han, C., and A. Drescher. 1993. “Shear bands in biaxial tests on dry coarse sand.” Soils Found. 33 (1): 118–132. https://doi.org/10.3208/sandf1972.33.118.
Hassoun, M., P. Villard, M. Al Heib, and F. Emeriault. 2018. “Soil reinforcement with geosynthetic for localized subsidence problems: Experimental and analytical analysis.” Int. J. Geomech. 18 (10): 04018133. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001265.
Hummel, F. H., and E. J. Finnan. 1921. “The distribution of pressure on surfaces supporting a mass of granular material.” Min. Proc. Inst. Civ. Eng.212: 369–392. https://doi.org/10.1680/imotp.1921.14900.
Iglesia, G. R., H. H. Einstein, and R. V. Whitman. 2014. “Investigation of soil arching with centrifuge tests.” J. Geotech. Geoenviron. 140 (2): 04013005. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000998.
Khiloun, M., A. A. Bousahla, A. Kaci, A. Bessaim, A. Tounsi, and S. R. Mahmoud. 2020. “Analytical modeling of bending and vibration of thick advanced composite plates using a four-variable quasi 3D HSDT.” Eng. Comput. 36 (3): 807–821. https://doi.org/10.1007/s00366-019-00732-1.
Koutsabeloulis, N. C., and D. V. Griffiths. 1989. “Numerical modelling of the trap door problem.” Geotechnique 39 (1): 77–89. https://doi.org/10.1680/geot.1989.39.1.77.
Lai, H. J., J. J. Zheng, J. Zhang, R. J. Zhang, and L. Cui. 2014. “DEM analysis of ‘soil’-arching within geogrid-reinforced and unreinforced pile-supported embankments.” Comput. Geotech. 61: 13–23. https://doi.org/10.1016/j.compgeo.2014.04.007.
Lai, H. J., J. J. Zheng, R. J. Zhang, and M. J. Cui. 2016. “Visualization of the formation and features of soil arching within a piled embankment by discrete element method simulation.” J. Zhejiang Univ. Sci. A 17 (10): 803–817. https://doi.org/10.1631/jzus.A1500302.
Lai, H. J., J. J. Zheng, and M. J. Cui. 2021. “Improved analytical soil arching model for the design of piled embankments.” Int. J. Geomech. 21 (3): 04020261. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001929.
Li, Z., W. Lin, J. Ye, Y. Chen, X. Bian, and F. Gao. 2021. “Soil movement mechanism associated with arching effect in a multi-strutted excavation in soft clay.” Tunnelling Underground Space Technol. 110: 103816. https://doi.org/10.1016/j.tust.2021.103816.
Liang, L., and C. Xu. 2019. “Numerical and theoretical research on stress distribution in the loosening zone of the trapdoor problem.” Int. J. Numer. Anal. Methods Geomech. 43 (7): 1426–1447. https://doi.org/10.1002/nag.2906.
Liang, L., C. Xu, Q. Chen, and Q. Chen. 2020. “Experimental and theoretical investigations on evolution of soil-arching effect in 2D trapdoor problem.” Int. J. Geomech. 20 (6): 06020007. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001643.
McGuire, M., J. Sloan, and G. Filz. 2020. “Effectiveness of geosynthetic reinforcement for load transfer in column-supported embankments.” Geosynth. Int. 27 (2): 200–218. https://doi.org/10.1680/jgein.19.00012.
Mehrabadi, M. M., and S. C. Cowin. 1978. “Initial planar deformation of dilatant granular materials.” J. Mech. Phys. Solids 26 (4): 269–284. https://doi.org/10.1016/0022-5096(78)90021-2.
Mühlhaus, H. B., J. Shi, L. Olsen-Kettle, and L. Moresi. 2011. “Effects of a non-coaxial flow rule on shear bands in viscous-plastic materials.” Granul. Matter 13 (3): 205–210. https://doi.org/10.1007/s10035-011-0254-7.
Murakami, A., H. Sakaguchi, and T. Hasegawa. 1997. “Dislocation, vortex and couple stress in the formation of shear bands under trap-door problems.” Soils Found. 37 (1): 123–135. https://doi.org/10.3208/sandf.37.123.
Oda, M., J. Konishi, and S. Nemat-Nasser. 1982. “Experimental micromechanical evaluation of strength of granular materials: Effects of particle rolling.” Mech. Mater. 1 (4): 269–283. https://doi.org/10.1016/0167-6636(82)90027-8.
Paikowsky, S. G., and H. S. Tien. 2002. “Experimental examination of the arching mechanism on the micro level.” In Discrete element methods: Numerical modeling of discontinua, Geotechnical Special Publication 117, edited by B. K. Cook and R. P. Jensen, 222–228. Reston, VA: ASCE.
Rabhi, M., K. H. Benrahou, A. Kaci, M. S. A. Houari, F. Bourada, A. A. Bousahla, A. Tounsi, E. A. Adda Bedia, S. R. Mahmoud, and A. Tounsi. 2020. “A new innovative 3-unknowns HSDT for buckling and free vibration of exponentially graded sandwich plates resting on elastic foundations under various boundary conditions.” Geomech. Eng. 22 (2): 119–132.
Rui, R., A. F. van Tol, Y. Y. Xia, S. J. M. van Eekelen, and G. Hu. 2016a. “Investigation of soil-arching development in dense sand by 2D model tests.” Geotech. Test. J. 39 (3): 20150130. https://doi.org/10.1520/GTJ20150130.
Rui, R., F. van Tol, X. L. Xia, S. van Eekelen, G. Hu, and Y. Y. Xia. 2016b. “Evolution of soil arching; 2D DEM simulations.” Comput. Geotech. 73: 199–209. https://doi.org/10.1016/j.compgeo.2015.12.006.
Rui, R., Y. X. Zhai, J. Han, S. J. M. van Eekelen, and C. Chen. 2020. “Deformations in trapdoor tests and piled embankments.” Geosynth. Int. 27 (2): 219–235. https://doi.org/10.1680/jgein.19.00014.
Sivakugan, N., S. Widisinghe, and V. Z. Wang. 2014. “Vertical stress determination within backfilled mine stopes.” Int. J. Geomech. 14 (5): 1–5. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000367.
Sloan, S. W., A. Assadi, and N. Purushothaman. 1990. “Undrained stability of a trapdoor.” Géotechnique 40 (1): 45–62. https://doi.org/10.1680/geot.1990.40.1.45.
Son, M. 2017. “Three-dimensional expansion of the Terzaghi arching formula considering inclined sliding surfaces and examination of its effects.” Int. J. Geomech. 17 (7): 06016043. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000844.
Spencer, A. J. M. 1964. “A theory of the kinematics of ideal soils under plane strain conditions.” J. Mech. Phys. Solids 12 (5): 337–351. https://doi.org/10.1016/0022-5096(64)90029-8.
Tanaka, T., and T. Sakai. 1993. “Progressive failure and scale effect of trap-door problems with granular materials.” Soils Found. 33 (1): 11–22. https://doi.org/10.3208/sandf1972.33.11.
Taylor, D. W. 1948. Fundamentals of soil mechanics. New York: John Wiley & Sons.
Terzaghi, K. 1943. Theoretical soil mechanics. Hoboken, NJ: John Wiley & Sons.
Terzaghi, K. V. 1936. “Stress distribution in dry and in saturated sand above a yielding trap-door.” In Proc., 1st Int. Conf. on Soil Mechanics and Foundation Engineering, 307–311. Cambridge, MA: Graduate School of Engineering, Harvard University.
Tounsi, A., S. U. Al-Dulaijan, M. A. Al-Osta, A. Chikh, M. M. Al-Zahrani, A. Sharif, and A. Tounsi. 2020. “A four variable trigonometric integral plate theory for hygro-thermo-mechanical bending analysis of AFG ceramic-metal plates resting on a two-parameter elastic foundation.” Steel Compos. Struct. 34 (4): 511–524.
Van Eekelen, S. J. M., A. Bezuijen, H. J. Lodder, and A. F. Van Tol. 2012a. “Model experiments on piled embankments. Part II.” Geotext. Geomembr. 32: 82–94. https://doi.org/10.1016/j.geotexmem.2011.11.003.
Van Eekelen, S. J. M., A. Bezuijen, H. J. Lodder, and A. F. Van Tol. 2012b. “Model experiments on piled embankments. Part I.” Geotext. Geomembr. 32: 69–81. https://doi.org/10.1016/j.geotexmem.2011.11.002.
Vanel, L., D. Howell, D. Clark, R. P. Behringer, and E. Clément. 1999. “Memories in sand: Experimental tests of construction history on stress distributions under sandpiles.” Phys. Rev. E - Stat. Phys. Plasmas Fluids Relat. Interdiscip. Top. 60 (5): R5040(R).
Völlmy, A. 1937. “Eingebettete rohre.” [In German.] Thesis/dissertation, Mitt. Inst. Baustatik, Eidgen. Tech. Hochschule.
Zheng, G., Y. Lei, X. Cheng, X. Li, and R. Wang. 2021. “Experimental study on the progressive collapse mechanism in the braced and tied-back retaining systems of deep excavations.” Can. Geotech. J. 58 (4): 540–564. https://doi.org/10.1139/cgj-2019-0296.
Zhu, B., D. Gao, J. C. Li, and Y. M. Chen. 2012. “Model tests on interaction between soil and geosynthetics subjected to localized subsidence in landfills.” J. Zhejiang Univ. Sci. A 13 (6): 433–444. https://doi.org/10.1631/jzus.A1100315.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Dec 1, 2020
Accepted: Sep 27, 2021
Published online: Nov 26, 2021
Published in print: Feb 1, 2022
Discussion open until: Apr 26, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.