Theoretical Analysis of Postconstruction Load-Carrying Capacity of a Cast-in-Place Pile Installed in K0-Consolidated Anisotropic Clayey Soil
Publication: International Journal of Geomechanics
Volume 21, Issue 9
Abstract
This paper analytically investigates the postconstruction load-carrying capacity of a cast-in-place pile in clayey soil. The stress release induced by borehole excavation, the slurry supporting effects, and the dissipation of the negative excess pore-water pressure after construction, all of which have significant effects on the effective stresses of the soil around the pile, are the main concerns of this study, which aim to establish a method to reasonably evaluate the load-carrying capacity of a cast-in-place pile after construction. The stress release due to borehole excavation is modeled by cylindrical cavity contraction theory, which employs a K0-consolidated anisotropic modified Cam-clay (K0-AMCC) model to represent the mechanical behavior of the soil. Considering the dissipation of the negative excess pore pressure, the load-carrying capacity after construction is determined by the total stress method, with consideration of the three-dimensional strength of the soil adjacent to the pile. The proposed method was verified by finite-element (FE) numerical simulations. The results indicate that the soil properties and the factors involved in pile construction, such as the stress release due to borehole excavation, the slurry supporting effects, and the dissipation of negative excess pore-water pressure, have substantial influences on the postconstruction load-carrying capacity of the pile.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (Grant Nos. 51878487 and 52008246), Shanghai Sailing Program (Grant No. 19YF1436700), and Open Research Project from Key Laboratory of Geotechnical and Underground Engineering, Tongji University (Grant No. KLE-TJGE-B1801). Financial support from these organizations is gratefully acknowledged.
References
Bradley, W. B. 1979. “Failure of inclined boreholes.” J. Energy Res. Technol. 101 (4): 232–239. https://doi.org/10.1115/1.3446925.
Brown, E. T., J. W. Bray, B. Ladanyi, and E. Hoek. 1983. “Ground response curves for rock tunnels.” J. Geotech. Eng. 109 (1): 15–39.
Carter, J. P., M. F. Randolph, and C. P. Wroth. 1979. “Stress and pore pressure changes in clay during and after the expansion of a cylindrical cavity.” Int. J. Numer. Anal. Methods Geomech. 3 (4): 305–322. https://doi.org/10.1002/nag.1610030402.
Chang, M. F., and H. Zhu. 2004. “Construction effect on load transfer along bored piles.” J. Geotech. Geoenviron. Eng. 130 (4): 426–437. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:4(426).
Charlez, P. A., and S. Roatesi. 1999. “A fully analytical solution of the wellbore stability problem under undrained conditions using a linearised Cam-clay model.” Oil Gas Sci. Technol. 54 (5): 551–563. https://doi.org/10.2516/ogst:1999047.
Chen, H. H., H. H. Zhu, and L. Y. Zhang. 2021. “Analytical solution for deep circular tunnels in rock with consideration of disturbed zone, 3D strength and large strain.” Rock Mech. Rock Eng. 54 (3): 1391–1410. https://doi.org/10.1007/s00603-020-02339-1.
Chen, S. L., and Y. N. Abousleiman. 2016. “Drained and undrained analyses of cylindrical cavity contractions by bounding surface plasticity.” Can. Geotech. J. 53 (9): 1398–1411. https://doi.org/10.1139/cgj-2015-0605.
Chen, S. L., and Y. N. Abousleiman. 2017. “Wellbore stability analysis using strain hardening and/or softening plasticity models.” Int. J. Rock Mech. Min. Sci. 93: 260–268. https://doi.org/10.1016/j.ijrmms.2017.02.007.
Chen, S. L., Y. N. Abousleiman, and K. K. Muraleetharan. 2012. “Closed-form elastoplastic solution for the wellbore problem in strain hardening/softening rock formations.” Int. J. Geomech. 12 (4): 494–507. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000157.
Chen, S. L., and K. Liu. 2019. “Undrained cylindrical cavity expansion in anisotropic critical state soils.” Géotechnique 69 (3): 189–202. https://doi.org/10.1680/jgeot.16.P.335.
Collins, I. F., and J. R. Stimpson. 1994. “Similarity solutions for drained a undrained cavity expansions in soils.” Géotechnique 44 (1): 21–34. https://doi.org/10.1680/geot.1994.44.1.21.
Graziani, A., and R. Ribacchi. 1993. “Critical conditions for a tunnel in a strain softening rock.” In Assessment and prevention of failure phenomena in rock engineering, edited by A. G. Pasamehmetoglu, T. Kawamoto, B. N. Whittaker, and O. Ayda, 199–204, Rotterdam, Netherlands: A.A. Balkema.
Guo, W. D. 2000. “Visco-elastic consolidation subsequent to pile installation.” Comput. Geotech. 26 (2): 113–144. https://doi.org/10.1016/S0266-352X(99)00028-2.
Li, L., H. H. Chen, J. P. Li, and D. A. Sun. 2021. “An elastoplastic solution to undrained expansion of a cylindrical cavity in SANICLAY under plane stress condition.” Comput. Geotech. 132: 103990. https://doi.org/10.1016/j.compgeo.2020.103990.
Li, L., S. L. Chen, and Z. J. Zhang. 2019. “A numerical study on installation effects and long-term shaft resistance of pre-bored piles in cohesive soils.” Transp. Res. Rec. 2673 (3): 494–505. https://doi.org/10.1177/0361198119835505.
Li, L., S. L. Chen, and Z. J. Zhang. 2020. “Practical analytical approach for estimating long-term and set-up shaft resistance of prebored piles.” J. Geotech. Geoenviron. Eng. 146 (10): 04020100. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002354.
Matsuoka, H., Y. P. Yao, and D. A. Sun. 1999. “The cam-clay models revised by the SMP criterion.” Soils Found. 39 (1): 81–95. https://doi.org/10.3208/sandf.39.81.
Randolph, M. F., J. P. Carter, and C. P. Wroth. 1979. “Driven piles in clay—The effects of installation and subsequent consolidation.” Géotechnique 29 (4): 361–393. https://doi.org/10.1680/geot.1979.29.4.361.
Randolph, M. F., and C. P. Wroth. 1979. “An analytical solution for the consolidation around a driven pile.” Int. J. Numer. Anal. Methods Geomech. 3 (3): 217–229. https://doi.org/10.1002/nag.1610030302.
Randolph, M. F., and C. P. Wroth. 1981. “Application of the failure state in undrained simple shear to the shaft capacity of driven piles.” Géotechnique 31 (1): 143–157. https://doi.org/10.1680/geot.1981.31.1.143.
Santarelli, F. J., E. T. Brown, and V. Maury. 1986. “Analysis of borehole stresses using pressure-dependent, linear elasticity.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 23 (6): 445–449. https://doi.org/10.1016/0148-9062(86)92310-7.
Sekiguchi, H., and H. Ohta. 1977. “Induced anisotropy and time dependency in clays.” In Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, 229–238, Tokyo: Japanese Society of Soil Mechanics and Foundation Engineering.
Sheil, B. B., and B. A. McCabe. 2016. “An analytical approach for the prediction of single pile and pile group behaviour in clay.” Comput. Geotech. 75: 145–158. https://doi.org/10.1016/j.compgeo.2016.02.001.
Sheil, B. B., B. A. McCabe, C. E. Hunt, and J. M. Pestana. 2015. “A practical approach for the consideration of single pile and pile group installation effects in clay: Numerical modelling.” J. Geoeng. Sci. 2 (3-4): 119–142.
Shen, S. L., J. Han, and Y. J. Du. 2008. “Deep mixing induced property changes in surrounding sensitive marine clays.” J. Geotech. Geoenviron. Eng. 134 (6): 845–854. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:6(845).
Shen, S. L., N. Miura, and H. Koga. 2003. “Interaction mechanism between deep mixing column and surrounding clay during installation.” Can. Geotech. J. 40 (2): 293–307. https://doi.org/10.1139/t02-109.
Shen, S. L., Z. F. Wang, and W. C. Cheng. 2017. “Estimation of lateral displacement induced by jet grouting in clayey soils.” Géotechnique 67 (7): 621–630. https://doi.org/10.1680/jgeot.16.P.159.
Shen, S. L., Z. F. Wang, J. Yang, and C. E. Ho. 2013. “Generalized approach for prediction of jet grout column diameter.” J. Geotech. Geoenviron. Eng. 139 (12): 2060–2069. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000932.
Shuttle, D. 2007. “Cylindrical cavity expansion and contraction in Tresca soil.” Géotechnique 57 (3): 305–308. https://doi.org/10.1680/geot.2007.57.3.305.
Wang, Z. F., S. L. Shen, G. Modoni, and A. Zhou. 2020. “Excess pore water pressure caused by the installation of jet grouting columns in clay.” Comput. Geotech. 125: 103667. https://doi.org/10.1016/j.compgeo.2020.103667.
Wehnert, M., and P. A. Vermeer. 2004. “Numerical analyses of load tests on bored piles.” In Proc., Numerical Models in Geomechanics, 505–511.
Wheeler, S. J., A. Näätänen, M. Karstunen, and M. Lojander. 2003. “An anisotropic elastoplastic model for soft clays.” Can. Geotech. J. 40 (2): 403–418. https://doi.org/10.1139/t02-119.
Wu, P., W. M. Gong, W. X. Ren, and Q. Z. You. 2008. “Effect of slurry on bearing performance of bored piles.” Chin. J. Geotech. Eng. 30 (9): 1327–1332.
Yang, C. Y., J. P. Li, L. Li, and D. A. Sun. 2021. “Expansion responses of a cylindrical cavity in overconsolidated unsaturated soils: A semi-analytical elastoplastic solution.” Comput. Geotech. 130: 103922. https://doi.org/10.1016/j.compgeo.2020.103922.
Yu, H. S., and R. K. Rowe. 1999. “Plasticity solutions for soil behaviour around contracting cavities and tunnels.” Int. J. Numer. Anal. Methods Geomech. 23 (12): 1245–1279. https://doi.org/10.1002/(SICI)1096-9853(199910)23:12%3C1245::AID-NAG30%3E3.0.CO;2-W.
Zhang, J., L. Li, and D. Sun. 2020. “Similarity solution for undrained cylindrical cavity contraction in anisotropic modified Cam-clay model soils.” Comput. Geotech. 120: 103405. https://doi.org/10.1016/j.compgeo.2019.103405.
Zhou, D. Q., and H. J. Tan. 2012. “Character and dimension effect of long spiral mud-jack bored pile’s pressure–settlement curve.” Appl. Mech. Mater. 170–173: 880–884. https://doi.org/10.4028/www.scientific.net/AMM.170-173.880.
Zhou, H., H. Liu, G. Kong, and X. Huang. 2014. “Analytical solution of undrained cylindrical cavity expansion in saturated soil under anisotropic initial stress.” Comput. Geotech. 55: 232–239. https://doi.org/10.1016/j.compgeo.2013.09.011.
Zhou, Z. Y., and C. Y. Zhang. 2014. “Causes and solutions for the common problems in rotary drilling cast-in-place pile construction.” Appl. Mech. Mater. 580–583: 2249–2252. https://doi.org/10.4028/www.scientific.net/AMM.580-583.2249.
Zhou, Z., T. Yang, and H. Fan. 2019. “A full-scale field study on bearing characteristics of cast-in-place piles with different hole-forming methods in loess area.” Adv. Civ. Eng. 2019: 1450163.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Oct 20, 2020
Accepted: May 7, 2021
Published online: Jun 25, 2021
Published in print: Sep 1, 2021
Discussion open until: Nov 25, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.