Control and Stabilization of Fugitive Dust: Using Eco-Friendly and Sustainable Materials
Publication: International Journal of Geomechanics
Volume 20, Issue 9
Abstract
Untreated soil is prone to erosion and dust generation that result in various environmental and health hazards. The addition of additives has been used as a soil treatment method to tackle this problem. Conventional techniques such as chemical additives impose negative ecological impacts and significant implementation and maintenance costs. This paper evaluates the efficiency of three eco-friendly biopolymers, xanthan gum, guar gum, and carboxymethyl cellulose (CMC) with 0.5%, 1%, and 1.5% concentrations for soil treatment against dust generation. This study also investigates the long-term performance and durability of biopolymers. Three types of samples (dust particles) were collected from different locations that generate the most dust in Iran: Hooralazim lagoon as a source of soil, Urmia lake bed as a source of saline sand, and Sungun copper mine as a source of mine tailing. Approximately 500 samples prepared and treated with different biopolymer concentrations were evaluated by the wind tunnel, moisture retention, surface strength, and uniaxial compression tests to identify the most effective biopolymer. The addition of biopolymers improved moisture retention, surface strength, compressive strength, and mitigation of dust generation. Scanning electron microscopy (SEM) imaging was also used to study the microstructures of the specimens after treatment. A strong correlation was found between the weight loss after the wind tunnel test versus the maximum penetration force and the uniaxial compressive strength. In terms of dust generation preventive treatment, CMC was more effective than xanthan gum and guar gum. Hence, CMC was introduced as an alternative material for dust control due to its promising potentials.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We would like to show our gratitude to Ms. Romina Chegeni, Ms. Hanieh Rajabi, and Mr. Morteza Azizmohammadi for their help in this research.
References
Annabi, M., S. Houot, C. Francou, M. Poitrenaud, and Y. L. Bissonnais. 2007. “Soil aggregate stability improvement with urban composts of different maturities.” Soil Sci. Soc. Am. J. 71 (2): 413–423. https://doi.org/10.2136/sssaj2006.0161.
ASTM. 2016. Standard test method for unconfined compressive strength of cohesive soil. ASTM D2166/D2166M-16. West Conshohocken, PA: ASTM.
Ayeldeen, M. K., A. M. Negm, and M. A. El Sawwaf. 2016. “Evaluating the physical characteristics of biopolymer/soil mixtures.” Arabian J. Geosci. 9 (5): 371. https://doi.org/10.1007/s12517-016-2366-1.
Bastan, M., F. Abdollahi, and K. Shokoufi. 2013. “Analysis of Iran’s dust emission with system dynamics methodology.” Tech. J. Eng. Appl. Sci. 3 (24): 3515–3524.
Bolander, P., and A. Yamada. 1999. Dust palliative selection and application guide. Washington, DC: U.S. Dept. of Agriculture.
Bouzza, A., W. P. Gates, and P. G. Ranjith. 2009. “Hydraulic conductivity of biopolymer-treated silty sand.” Géotechnique 59 (1): 71–72. https://doi.org/10.1680/geot.2007.00137.
Carvalho, A. J. F. 2008. “Starch: Major sources, properties and applications as thermoplastic materials.” In Monomers, polymers and composites from renewable resources, edited by M. N. Belgacem, and A. Gandini, 321–342. Amsterdam, Netherlands: Elsevier.
Chang, I., and G. C. Cho. 2012. “Strengthening of Korean residual soil with β-1,3/1,6-glucan biopolymer.” Constr. Build. Mater. 30: 30–35. https://doi.org/10.1016/j.conbuildmat.2011.11.030.
Chang, I., and G. C. Cho. 2014. “Geotechnical behavior of a beta-1,3/1,6-glucan biopolymer-treated residual soil.” Geomech. Eng. 7 (6): 633–647. https://doi.org/10.12989/gae.2014.7.6.633.
Chang, I., J. Im, and G. C. Cho. 2016. “Introduction of microbial biopolymers in soil treatment for future environmentally-friendly and sustainable geotechnical engineering.” Sustainability 8 (3): 251. https://doi.org/10.3390/su8030251.
Chang, I., J. Im, A. K. Prasidhi, and G. C. Cho. 2015. “Effects of Xanthan gum biopolymer on soil strengthening.” Constr. Build. Mater. 74: 65–72. https://doi.org/10.1016/j.conbuildmat.2014.10.026.
Chen, R., I. Lee, and L. Zhang. 2015. “Biopolymer stabilization of mine tailings for dust control.” J. Geotech. Geoenviron. Eng. 141 (2): 04014100. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001240.
Chen, R., X. Ding, D. Ramey, I. Lee, and L. Zhang. 2016. “Experimental and numerical investigation into surface strength of mine tailings after biopolymer stabilization.” Acta Geotech. 11 (5): 1075–1085. https://doi.org/10.1007/s11440-015-0420-x.
Dehghan, H., A. Tabarsa, N. Latifi, and Y. Bagheri. 2019. “Use of xanthan and guar gums in soil strengthening.” Clean Technol. Environ. Policy 21 (1): 155–165. https://doi.org/10.1007/s10098-018-1625-0.
Etemadi, O., I. G. Petrisor, D. Kim, M.-W. Wan, and T. F. Yen. 2003. “Stabilization of metals in subsurface by biopolymers: Laboratory drainage flow studies.” Soil Sediment Contam. 12 (5): 647–661. https://doi.org/10.1080/714037712.
Gerente, C., V. K. C. Lee, P. Le Cloirec, and G. McKay. 2007. “Application of chitosan for the removal of metals from wastewaters by adsorption—Mechanisms and models review.” Crit. Rev. Env. Sci. Technol. 37 (1): 41–127. https://doi.org/10.1080/10643380600729089.
Ghannam, M. T., and M. N. Esmail. 1997. “Rheological properties of carboxymethyl cellulose.” J. Appl. Polym. Sci. 64 (2): 289–301. https://doi.org/10.1002/(SICI)1097-4628(19970411)64:2%3C289::AID-APP9%26gt;3.0.CO;2-N.
Ghassemi, P., and V. Toufigh. 2020. “Durability of epoxy polymer and ordinary cement concrete in aggressive environments.” Constr. Build. Mater. 234: 117887. https://doi.org/10.1016/j.conbuildmat.2019.117887.
Gholampour, A., R. Nabizadeh, M. S. Hassanvand, H. Taghipour, S. Nazmara, and A. H. Mahvi. 2015. “Characterization of saline dust emission resulted from Urmia Lake drying.” J. Environ. Health Sci. Eng. 13 (1): 82. https://doi.org/10.1186/s40201-015-0238-3.
Gibis, M., V. Schuh, and J. Weiss. 2015. “Effects of carboxymethyl cellulose (CMC) and microcrystalline cellulose (MCC) as fat replacers on the microstructure and sensory characteristics of fried beef patties.” Food Hydrocolloids 45: 236–246. https://doi.org/10.1016/j.foodhyd.2014.11.021.
Gong, Y., and D. Zhao. 2013. “In situ immobilization of mercury in water, soil, and sediment using carboxymethyl cellulose stabilized iron sulfide nanoparticles.” In Vol. 1123 of Novel Solutions to Water Pollution, ACS Symposium Series, edited by S. Ahuja, and K. Hristovski, 61–77. Washington, DC: ACS.
He, F., D. Zhao, J. Liu, and C. B. Roberts. 2007. “Stabilization of Fe–Pd nanoparticles with sodium carboxymethyl cellulose for enhanced transport and dechlorination of trichloroethylene in soil and groundwater.” Ind. Eng. Chem. Res. 46 (1): 29–34. https://doi.org/10.1021/ie0610896.
He, F., M. Zhang, T. Qian, and D. Zhao. 2009. “Transport of carboxymethyl cellulose stabilized iron nanoparticles in porous media: Column experiments and modeling.” J. Colloid Interface Sci. 334 (1): 96–102. https://doi.org/10.1016/j.jcis.2009.02.058.
Heinze, T., and A. Koschella. 2005. “Carboxymethyl ethers of cellulose and starch—A review.” Macromol. Symp. 223 (1): 13–40. https://doi.org/10.1002/masy.200550502.
Ivanov, V., and J. Chu. 2008. “Applications of microorganisms to geotechnical engineering for bioclogging and biocementation of soil in situ.” Rev. Environ. Sci. Biotechnol. 7: 139–153. https://doi.org/10.1007/s11157-007-9126-3.
Karimi, S. 1999. A study of geotechnical applications of biopolymer treated soils with an emphasis on silt. Los Angeles: Univ. of Southern California.
Kavazanjian, E., E. Iglesias, and I. Karatas. 2009. “Biopolymer soil stabilization for wind erosion control.” In Proc., 17th Int. Conf. on Soil Mechanics and Geotechnical Engineering: The Academia and Practice of Geotechnical Engineering, 881–884. Alexandria, Egypt: Proceedings of the 17th International Conference on Soil Mechanics and Geotechnical Engineering: The Academia and Practice of Geotechnical Engineering.
Khachatoorian, R., I. G. Petrisor, C. C. Kwan, and T. F. Yen. 2003. “Biopolymer plugging effect: Laboratory-pressurized pumping flow studies.” J. Pet. Sci. Eng. 38 (1–2): 13–21. https://doi.org/10.1016/S0920-4105(03)00019-6.
Khatami, H. R., and B. C. O’Kelly. 2013. “Improving mechanical properties of sand using biopolymers.” J. Geotech. Geoenviron. Eng. 139 (8): 1402–1406. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000861.
Maher, M. H., and Y. C. Ho. 1994. “Mechanical properties of kaolinite/fiber soil composite.” J. Geotech. Eng. 120 (8): 1381–1393. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:8(1381).
Martin, G. R., T. F. Yen, and S. Karimi. 1996. “Application of biopolymer technology in silty soil matrices to form impervious barriers.” In Proc., 7th Australia New Zealand Conf. on Geomechanics: Geomechanics in a Changing World: Conf. Proc., 814–819. Adelaide, Australia: Institution of Engineers.
McArdle, R., and R. Hamill. 2011. “Utilisation of hydrocolloids in processed meat systems.” Processed meats: Improving safety, nutrition and quality, edited by J. P. Kerry, and J. F. Kerry, 243–269. Amsterdam, Netherlands: Elsevier.
McHugh, D. J. 2003. A guide to the seaweed industry. Rome: Food and Agriculture Organization.
Nugent, R. A., G. Zhang, and R. P. Gambrell. 2009. “Effect of exopolymers on the liquid limit of clays and its engineering implications.” Transp. Res. Rec. 2101 (1): 34–43. https://doi.org/10.3141/2101-05.
Pham, V., L. van Paassen, A. Nakano, M. Kanayama, and T. Heimovaara. 2013. “Microbially induced carbonate precipitation (MICP) by denitrification as ground improvement method-process control in sand column experiments.” In EGU General Assembly Conference Abstracts. Vienna, Austria: EGU General Assembly Conference Abstracts.
Piechota, T. C., J. van Ee, K. A. Stave, and D. E. James. 2004. Potential environmental impacts of dust suppressants: “avoiding another times beach”. Washington, DC: U.S. Environmental Protection Agency.
Plank, J. 2004. “Applications of biopolymers and other biotechnological products in building materials.” Appl. Microbiol. Biotechnol. 66 (1): 1–9. https://doi.org/10.1007/s00253-004-1714-3.
Rahbari, M., M. Kianirad, S. M. Heydarian, and S. S. Mirdamadi. 2017. “Effects of pH and Fe(III) concentrations in Xanthan gum treatments on soil penetrability resistance.” Soil Sci. Soc. Am. J. 81 (4): 775–780. https://doi.org/10.2136/sssaj2016.11.0366.
Rice, M. A., C. E. Mullins, and I. K. McEwan. 1997. “An analysis of soil crust strength in relation to potential abrasion by saltating particles.” Earth Surf. Processes Landforms 22 (9): 869–883. https://doi.org/10.1002/(SICI)1096-9837(199709)22:9%3C869::AID-ESP785%26gt;3.0.CO;2-P.
Saha, D., and S. Bhattacharya. 2010. “Hydrocolloids as thickening and gelling agents in food: A critical review.” J. Food Sci. Technol. 47 (6): 587–597. https://doi.org/10.1007/s13197-010-0162-6.
Sahoo, D., and P. L. Nayak. 2011. “Chitosan: The most valuable derivative of chitin.” In Biopolymers: Biomedical and environmental applications, edited by S. Kalia, and L. Avérous, 129–166. Hoboken, NJ: Wiley.
Sivakumar Babu, G. L., and A. K. Vasudevan. 2008. “Strength and stiffness response of coir fiber-reinforced tropical soil.” J. Mater. Civ. Eng. 20 (9): 571–577. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:9(571).
Taguchi, G., S. Chowdhury, and Y. Wu. 2005. Taguchi’s quality engineering handbook. Hoboken, NJ: Wiley.
Tang, J., M. A. Tung, and Y. Zeng. 1997. “Gelling properties of gellan solutions containing monovalent and divalent cations.” J. Food Sci. 62 (4): 688–712. https://doi.org/10.1111/j.1365-2621.1997.tb15436.x.
Toufigh, V., M. Yarigarravesh, and M. Mofid. 2018. “The long-term evaluation of FRPs bonded to timber.” Eur. J. Wood Wood Prod. 76 (6): 1623–1636. https://doi.org/10.1007/s00107-018-1337-5.
Wan, M. W., I. G. Petrisor, H. T. Lai, D. Kim, and T. F. Yen. 2004. “Copper adsorption through chitosan immobilized on sand to demonstrate the feasibility for in situ soil decontamination.” Carbohydr. Polym. 55 (3): 249–254. https://doi.org/10.1016/j.carbpol.2003.09.009.
Yarigarravesh, M., V. Toufigh, and M. Mofid. 2018. “Experimental and analytical evaluation of FRPs bonded to masonry-long term.” Surf. Coat. Technol. 344: 729–741. https://doi.org/10.1016/j.surfcoat.2018.02.088.
Zhang, J.-N., Y.-H. Li, H.-Q. Zheng, Y.-T. Fan, and H.-W. Hou. 2015. “Direct degradation of cellulosic biomass to bio-hydrogen from a newly isolated strain Clostridium sartagoforme FZ11.” Bioresour. Technol. 192: 60–67. https://doi.org/10.1016/j.biortech.2015.05.034.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 20 • Issue 9 • September 2020
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Oct 6, 2019
Accepted: Mar 23, 2020
Published online: Jun 17, 2020
Published in print: Sep 1, 2020
Discussion open until: Nov 17, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.