Helical Piles Installed in Cohesionless Soil by Displacement Method
Publication: International Journal of Geomechanics
Volume 19, Issue 7
Abstract
This paper presents a detailed investigation carried out for a helical pile installed in cohesionless soil by the displacement method. Laboratory experiments were conducted on models to study the various factors influencing the axial capacities of helical piles. The investigation showed that relative density of soil plays a significant role in the response of axial capacity of piles to geometrical variations in helical blade diameter and shaft diameter. Presence of a helical blade and its geometry (Dh) were found to influence the axial capacity significantly. The effect of method of installation on axial capacity of helical piles was investigated, and helical piles installed by the displacement method were found to show an improvement of axial capacity on the order of 1.1–1.4 times in compression and 1.8–3.0 times in tension from experimental observations. To augment the investigation, analyses were carried out using three-dimensional finite-element software (Plaxis 3D AE) on the numerical model calibrated using the results from the experimental investigation. Cavity expansion by volumetric strain was found to capture the effect of installation of helical piles by displacement method in cohesionless soil. The results of the parametric study accommodating the effect of installation by displacement method, considering different soil densities and geometric features of helical piles, were used to propose a set of semiempirical relations for predicting axial tensile and compressive capacities. A set of reduction factors were also proposed to accommodate the difference in end-bearing response of helical piles compared to a prismatic pile of identical toe diameter.
Get full access to this article
View all available purchase options and get full access to this article.
References
Basu, P., D. Loukidis, M. Prezzi, and R. Salgado. 2011. “Analysis of shaft resistance of jacked piles in sands.” Int. J. Numer. Anal. Methods Geomech. 35 (15): 1605–1635. https://doi.org/10.1002/nag.968.
Basu, P., M. Prezzi, and D. Basu. 2010. “Drilled displacement piles—Current practice and design.” DFI J. 4 (1): 3–20. https://doi.org/10.1179/dfi.2010.001.
Broere, W., and A. F. van Tol. 2006. “Modelling the bearing capacity of displacement piles in sand.” Proc. Inst. Civ. Eng. Geotech. Eng. 159 (3): 195–206. https://doi.org/10.1680/geng.2006.159.3.195.
Brown, D. A. 2005. “Practical considerations in the selection and use of continuous flight auger and drilled displacement piles.” In Proc., GeoFrontiers, Advances in Designing and Testing Deep Foundations: In Memory of Michael W. O'Neill, 251–261. Austin, TX: ASCE.
BSI (British Standards Institute). 2015. Code of practice for foundations. BS 8004. London: BSI.
Bureau of Indian Standards. 1970. Indian standard classification and identification of soils for general engineering purposes. IS 1498. New Delhi, India: Bureau of Indian Standards.
Busch, P., J. Grabe, and F. W. Gerressen. 2013. “Influence of the installation process of full displacement bored piles on the subsoil.” Baltic piling, 157–163. Boca Raton, FL: CRC Research Press.
Clemence, S. P., and C. J. Veesaert. 1977. “Dynamic pullout resistance of anchors in sand.” In Proc., Int. Symp. On Soil-Structure Interaction, 389–397. Roorkee, India.
Das, B. M., and K. Sobhan. 2013. Principles of geotechnical engineering. Stamford, CT: Cengage Learning.
Dijkstra, J., W. Broere, A. Bezuijen, and A. F. vanTol. 2008. “Density changes near an advancing displacement pile in sand.” In Proc., 2nd BGA Int. Conf. on Foundations, ICOF2008. 545–554. Dundee, Scotland: British Geotechnical Association.
Dijkstra, J., W. Broere, and O. M. Heeres. 2011. “Numerical simulation of pile installation.” Comput. Geotech. 38 (5): 612–622. https://doi.org/10.1016/j.compgeo.2011.04.004.
Dung, P. H. 2009. “Modelling of installation effect of driven piles by hypoplasticity.” M.Sc. thesis, Section of Geotechnical Engineering Faculty of Civil Engineering and Geosciences, Delft Univ. of Technology.
Egan, D. 2009. “Installation effects of vibro replacement stone columns in soft clay.” In Proc., 2nd Int. Workshop on Geotechnics of Soft Soils, 23–29. Glasgow, Germany: CRC Press.
Elsherbiny, Z. H., and M. H. El Naggar. 2013. “Axial compressive capacity of helical piles from field tests and numerical study.” Can. Geotech. J. 50 (12): 1191–1203. https://doi.org/10.1139/cgj-2012-0487.
Engin, H. K., R. B. Brinkgreve, and A. F. van Tol. 2015. “Approximation of pile installation effects: A practical tool.” Proc. Inst. Civ. Eng. Geotech. Eng. 168 (4): 319–334. https://doi.org/10.1680/geng.14.00064.
Fahmy, A., and M. H. El Naggar. 2017. “Axial performance of helical tapered piles in sand.” Geotech. Geol. Eng. 35 (4): 1–28. https://doi.org/10.1007/s10706-017-0192-1.
Filho, J. M. S. M. D. S., T. D. S. O. Morais, and C. H. C. Tsuha. 2014. “A new experimental procedure to investigate the torque correlation factor of helical anchors.” Electron. J. Geotech. Eng. 19: 3851–3864.
Foray, P., E. Flavigny, N. T. Nguyen, S. Lambert, and L. Briançon. 2009. “3D numerical modeling of stone columns and application.” In Vol. 3 of Proc., 17th Int. Conf. on Soil Mechanics and Geotechnical Engineering, 2382–2385. Amsterdam, Netherlands: IOS Press.
Gandhi, S. R., and S. Selvam. 1997. “Group effect on driven piles under lateral load.” J. Geotech. Geoenviron. Eng. 123 (8): 702–709. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:8(702).
Gavin, K., P. Doherty, and A. Tolooiyan. 2014. “Field investigation of the axial resistance of helical piles in dense sand.” Can. Geotech. J. 51 (11): 1343–1354. https://doi.org/10.1139/cgj-2012-0463.
George, B. E., S. Banerjee, and S. R. Gandhi. 2017. “Numerical analysis of helical piles in cohesionless soil.” Int. J. Geotech. Eng. 1–15. https://doi.org/10.1080/19386362.2017.1419912.
Ghaly, A. M. 1995. “Drivability and pullout resistance of helical units in saturated sands.” Soils Found. 35 (2): 61–66. https://doi.org/10.3208/sandf1972.35.2_61.
Ghaly, A., and A. Hanna. 1992. “Stresses and strains around helical screw anchors in sand.” Soils Found. 32 (4): 27–42. https://doi.org/10.3208/sandf1972.32.4_27.
Ghaly, A., and A. Hanna. 2003. “Response of anchors to variations in displacement-based loading.” Can. Geotech. J. 40 (3): 694–701. https://doi.org/10.1139/t03-003.
Ghaly, A., A. Hanna, and M. Hanna. 1991a. “Installation torque of screw anchors in dry sand.” Soils Found. 31 (2): 77–92. https://doi.org/10.3208/sandf1972.31.2_77.
Ghaly, A., A. Hanna, and M. Hanna. 1991b. “Uplift behavior of screw anchors in sand. I: Dry sand.” J. Geotech. Eng. 117 (5): 773–793. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:5(773).
Ghaly, A., A. Hanna, and M. Hanna. 1991c. “Uplift behavior of screw anchors in sand. II: Hydrostatic and flow conditions.” J. Geotech. Eng. 117 (5): 794–808. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:5(794).
Ghaly, A., A. Hanna, G. Ranjan, and M. Hanna. 1991d. “Helical anchors in dry and submerged sand subjected to surcharge.” J. Geotech. Eng. 117 (10): 1463–1470. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:10(1463).
Hird, C. C., Q. Ni, and I. Guymer. 2011. “Physical modelling of deformations around piling augers in clay.” Géotechnique 61 (11): 993–999. https://doi.org/10.1680/geot.9.T.028.
Hurley, O. and Karray, M. 2015. “Finite element modelling of stone column installation: Review of modelling practices and case study with Plaxis 2D.” https://www.researchgate.net/publication/282130848.
Hurley, O., M. Nuth, M. Karray, F. Massé, C. Mollereau, M. Bouassida, and M. Chekired. 2013. “Physical modeling of stone column installation in fine sand and its effect on lateral to vertical stress ratio.” In Proc., GeoMontreal 2013. Montreal, Canada: Canadian Geotechnical Society.
Jardine, R. J., B. T. Zhu, P. Foray, and Z. X. Yang. 2013. “Interpretation of stress measurements made around closed-ended displacement piles in sand.” Géotechnique 63 (8): 613–627. https://doi.org/10.1680/geot.9.P.138.
Jeffrey, J. 2012. “Investigating the performance of continuous helical displacement piles.” Doctoral dissertation, Div. of Civil Engineering, Univ. of Dundee.
Krasinski, A. 2011. “Advanced field investigation of screw piles and columns.” Arch. Civ. Eng. 57 (1): 45–57. https://doi.org/10.2478/v.10169-011-0005-5.
Krasiński, A. 2012. “Proposal for calculating the bearing capacity of screw displacement piles in non-cohesive soils based on CPT results.” Studia Geotech. Mech. 34 (4): 41–51. https://doi.org/10.2478/sgm041204.
Krasinski, A. 2014. “The analysis of soil resistance during screw displacement pile installation.” Studia Geotech. Mech. 36 (3): 49–56. https://doi.org/10.2478/sgem-2014-0026.
Kurian, N. P., and S. J. Shah. 2009. “Studies on the behaviour of screw piles by the finite element method.” Can. Geotech. J. 46 (6): 627–638. https://doi.org/10.1139/T09-008.
Liu, H., H. K. Zubeck, and D. H. Schubert. 2007. “Finite-element analysis of helical piers in frozen ground.” J. Cold Reg. Eng. 21 (3): 92–106. https://doi.org/10.1061/(ASCE)0887-381X(2007)21:3(92).
Livneh, B., and M. H. El Naggar. 2008. “Axial testing and numerical modeling of square shaft helical piles under compressive and tensile loading.” Can. Geotech. J. 45 (8): 1142–1155. https://doi.org/10.1139/T08-044.
Malik, A. A., J. Kuwano, S. Tachibana, and T. Maejima. 2017. “End bearing capacity comparison of screw pile with straight pipe pile under similar ground conditions.” Acta Geotech. 12 (2): 415–428. https://doi.org/10.1007/s11440-016-0482-4.
Meng, Z., J. J. Chen, L. Zhang, J. H. Wang, and J. M. Yao. 2015. “Field tests to investigate the installation effects of drilled displacement piles with screw-shaped shaft in clay.” J. Geotech. Geoenviron. Eng. 141 (12): 06015010. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001371.
Meyerhof, G. G., and J. I. Adams. 1968. “The ultimate uplift capacity of foundations.” Can. Geotech. J. 5 (4): 225–244. https://doi.org/10.1139/t68-024.
Mitsch, M. P., and S. P. Clemence. 1985. “The uplift capacity of helix anchors in sand.” In Proc., Uplift behavior of anchor foundations in soil, 26–47. Reston, VA: ASCE.
Mittal, S., and S. Mukherjee. 2013. “Vertical uplift capacity of a group of helical screw anchors in sand.” Indian Geotech. J. 43 (3): 238–250. https://doi.org/10.1007/s40098-013-0055-5.
Nazir, R., H. S. Chuan, H. Niroumand, and K. A. Kassim. 2014. “Performance of single vertical helical anchor embedded in dry sand.” Measurement 49 (Mar): 42–51. https://doi.org/10.1016/j.measurement.2013.11.031.
Nyström, M., and V. Persson. 2016. “Soil displacement due to piling.” M.S. thesis, Chalmers Univ. of Technology.
Papadopoulou, K., H. Saroglou, and V. Papadopoulos. 2014. “Finite element analyses and experimental investigation of helical micropiles.” Geotech. Geol. Eng. 32 (4): 949–963. https://doi.org/10.1007/s10706-014-9771-6.
Prakash, S., and H. D. Sharma. 1990. Pile foundations in engineering practice. New York: John Wiley and Sons.
Pucker, T., and J. Grabe. 2012. “Numerical simulation of the installation process of full displacement piles.” Comput. Geotech. 45 (Sep): 93–106. https://doi.org/10.1016/j.compgeo.2012.05.006.
Qiu, G., S. Henke, and J. Grabe. 2011. “Application of a coupled Eulerian–Lagrangian approach on geomechanical problems involving large deformations.” Comput. Geotech. 38 (1): 30–39. https://doi.org/10.1016/j.compgeo.2010.09.002.
Rajapakse, R. 2008. Pile design for structural and geotechnical engineers. Oxford, UK: Butterworth Heinemann.
Sakr, M. 2011. “Installation and performance characteristics of high capacity helical piles in cohesionless soils.” DFI J. 5 (1): 39–57. https://doi.org/10.1179/dfi.2011.004.
Sakr, M. 2015. “Relationship between installation torque and axial capacities of helical piles in cohesionless soils.” Can. Geotech. J. 52 (6): 747–759. https://doi.org/10.1139/cgj-2013-0395.
Sakr, M., R. Mitchells, and J. Kenzie. 2009. “Pile load testing of helical piles and driven steel pipes in Anchorage, AK.” In Proc., 34th Annual Deep Foundation Conf., Kansas City, MO: DFI.
Salgado, R., J. K. Mitchell, and M. Jamiolkowski. 1997. “Cavity expansion and penetration resistance in sand.” J. Geotech. Geoenviron. Eng. 123 (4): 344–354. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:4(344).
Salhi, L., O. Nait-Rabah, C. Deyrat, and C. Roos. 2013. “Numerical modeling of single helical pile behavior under compressive loading in sand.” Electron. J. Geotech. Eng. 18: 4319–4338.
Shalabi, F. I., and T. A. Bader. 2014. “Effect of sand densification due to pile driving on pile resistance.” Int. J. Civ. Eng. 3 (1): 17–30.
Shien, N. K. 2013. “Cavity expansion approach in modelling stone column installation effect.” Int. J. Adv. Eng., Sci. Technol. 2 (2): 252–260.
Spagnoli, G. and K. Gavin. 2015. “Helical piles as a novel foundation system for offshore piled facilities.” In Proc., Abu Dhabi International Petroleum Exhibition and Conf. Richardson, TX: Society of Petroleum Engineers.
Sutherland, H. B. 1965. “Model studies of shaft raising through cohesionless soils.” In Vol. 2 of Proc., 6th Int. Conf. on Soil Mechanics and Foundation Engineering, 410–413. Toronto, Canada: University of Toronto Press.
Tappenden, K. M. 2007. “Predicting the axial capacity of screw piles installed in Western Canadian soils.” M.Sc. thesis, Univ. of Alberta.
Tappenden, K. M., and D. C. Sego. 2007. “Predicting the axial capacity of screw piles installed in Canadian soils.” In Vol. 3 of Proc., 60th Canadian Geotechnical Conf., OttawaGeo2007, 1608–1615. Ottawa, ON, Canada: Canadian Geotechnical Society.
Thiyyakkandi, S., M. McVay, D. Bloomquist, and P. Lai. 2014. “Experimental study, numerical modeling of and axial prediction approach to base grouted drilled shafts in cohesionless soils.” Acta Geotech. 9 (3): 439–454. https://doi.org/10.1007/s11440-013-0246-3.
Tsuha, C. D. H. C., and N. Aoki. 2010. “Relationship between installation torque and uplift capacity of deep helical piles in sand.” Can. Geotech. J. 47 (6): 635–647. https://doi.org/10.1139/T09-128.
Tsukamoto, Y., K. Ishihara, M. Yamamoto, K. Harada, and H. Yabe. 2000. “Soil densification due to static sand pile installation for liquefaction remediation.” Soils Found. 40 (2): 9–20. https://doi.org/10.3208/sandf.40.2_9.
Verma, A. K. and R. K. Joshi. 2010. “Uplift load carrying capacity of piles in sand.” In Indian Geotechnical Conf., GEOTrendz, 857–860. Mumbai, India: Indian Geotechnical Society.
Vesic, A. B. 1963. “Bearing capacity of deep foundations in sand.” Highway Res. Rec. 39: 112–153.
Wei, X., and Y. Wang, 2010. “Simulation of anti-flood spiral pile driving process based on ANSYS/LS_DYNA.” In Proc., World Automation Congress (WAC), 239–243. New York: IEEE.
Wood, D. M. 2003. Geotechnical modelling. Vol. 1. Boca Raton, FL: CRC Press.
Woodcock, J. 2012. “Finite element analysis of screw piles.” In Proc., 1st Civil and Environmental Engineering Student Conf. London: Imperial College.
Zarrabi, M., and A. Eslami. 2016. “Behavior of piles under different installation effects by physical modeling.” Int. J. Geomech. 16 (5): 04016014. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000643.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: May 15, 2018
Accepted: Jan 24, 2019
Published online: May 6, 2019
Published in print: Jul 1, 2019
Discussion open until: Oct 6, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.