Shear Modulus and Damping Ratio Model for Cement Treated Clay
Publication: International Journal of Geomechanics
Volume 19, Issue 7
Abstract
A hyperbolic model-based normalized shear modulus reduction (G/Gmax) formulation for cement treated clay is presented. This three-parameter normalized shear modulus reduction model can be constructed using maximum shear modulus and isotropic compression experiments. The model assumes that cemented clay follows the failure pattern of a modified structured Cam-clay model. The effects of cement content and confining pressures on G/Gmax are modeled and validated with experimental results from resonant column and cyclic triaxial testing. In addition, the damping ratio is calculated based on the Masing rule; however, for cement treated clays, this rule overestimates the damping ratio at all ranges of shear strain. In this study, correction factors are established to propose a reliable damping ratio model. The newly proposed G/Gmax and damping formulations provide reasonable estimates that match well with the experimental results. These formulations can be used in the seismic response analysis of cement treated ground.
Get full access to this article
View all available purchase options and get full access to this article.
References
Borden, R., L. Shao, and A. Gupta. 1996. “Dynamic properties of piedmont residual soils.” J. Geotech. Engrg. 122 (10): 813–821. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:10(813).
CDIT (Coastal Development Institute of Technology). 2002. The deep mixing method: Principle, design and construction, 1–123. Lisse, Netherlands: A. A. Balkema.
Darendeli, M. B. 2001. “Development of a new family of normalized modulus reduction and material damping curves.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Texas.
El Mohtar, C. S., V. P. Drnevich, M. Santagata, and A. Bobet. 2013. “Combined resonant column and cyclic triaxial tests for measuring undrained shear modulus reduction of sand with plastic fines.” Geotech. Test. J. 36 (4): 1–9. https://doi.org/10.1520/GTJ20120129.
Hardin, B. O., and V. P. Drnevich. 1972. “Shear modulus and damping in soils: Design equations and curves.” J. Soil Mech. Found. Eng. Div. 98 (7): 667–692.
Horpibulsuk, S., M. D. Liu, S. Liyanapathirana, and J. Suebsuk. 2010. “Behaviour of cemented clay simulated via the theoretical framework of the structured cam clay model.” Comput. Geotech. 37 (1–2): 1–9. https://doi.org/10.1016/j.compgeo.2009.06.007.
Hoyos, L., A. Puppala, and P. Chainuwat. 2004. “Dynamic properties of chemically stabilized sulfate rich clay.” J. Geotech. Geoenviron. Eng. 130 (2): 153–162. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:2(153).
Ishibashi, I., and X. Zhang. 1993. “Unified dynamic shear moduli and damping ratios of sand and clay.” Soils Found. 33 (1): 182–191. https://doi.org/10.3208/sandf1972.33.182.
Ishihara, K. 1996. Soil behavior in earthquake geotechnics. Oxford, UK: Clarendon Press.
Iwan, W. D. 1966. “A distributed-element model for hysteresis and its steady-state dynamic response.” J. Appl. Mech. 33 (4): 893–900. https://doi.org/10.1115/1.3625199.
Jennings, P. C. 1963. “Response of simple yielding structures to earthquake excitation.” Ph.D. dissertation, California Institute of Technology.
Kasama, K., H. Ochiai, and N. Yasufuku. 2000. “On the stress-strain behaviour of lightly cemented clay based on an extended critical state concept.” Soils Found. 40 (5): 37–47. https://doi.org/10.3208/sandf.40.5_37.
Kokusho, T., Y. Yoshida, and Y. Esashi. 1982. “Dynamic properties of soft clay for wide strain range.” Soils Found. 22 (4): 1–18. https://doi.org/10.3208/sandf1972.22.4_1.
Lee, K., D. Chan, and K. Lam. 2004. “Constitutive model for cement treated clay in a critical state frame work.” Soils Found. 44 (3): 69–77. https://doi.org/10.3208/sandf.44.3_69.
Liu, M. D., and J. P. Carter. 2002. “A structured Cam Clay model.” Can. Geotech. J. 39 (6): 1313–1332. https://doi.org/10.1139/t02-069.
Masing, G. 1926. “Eigenspannungen und verfestigung beim messing (1926).” [Self stretching and hardening for brass.] In Proc., 2nd Int. Congress Applied Mechanics, 332–335. Zurich, Switzerland: Orell Füssli.
Matasovic, N., and M. Vucetic. 1993. “Cyclic characterization of liquefiable sands.” J. Geotech. Engrg. 119 (11): 1805–1822. https://doi.org/10.1061/(ASCE)0733-9410(1993)119:11(1805).
Moon, S. W., and T. Ku. 2018. “Undrained shear strength in cohesive soils estimated by directional modes of in-situ shear wave velocity.” Geotech. Geol. Eng. 36 (5): 2851–2868. https://doi.org/10.1007/s10706-018-0508-9.
Nasim, A. S. M. 1999. “Numerical modeling of soil profile and behaviour in deep excavation analyses.” Master’s thesis, Dept. of Civil Engineering, National Univ. of Singapore.
Nguyen, L., B. Fatahi, and H. Khabbaz. 2017. “Development of a constitutive model to predict the behavior of cement-treated clay during cementation degradation: C3 model.” Int. J. Geomech. 17 (7): 1–32. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000863.
Pestana, J., and L. Salvati. 2006. “Small-strain behavior of granular soils. I. Model for cemented and cemented sands and gravels.” J. Geotech. Geoenviron. Eng. 132 (8): 1071–1081. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:8(1071).
Potts, D. M., G. T. Dounias, and P. R. Vaughan. 1990. “Finite element analysis of progressive failure of Carsington embankment.” Géotechnique 40 (1): 79–101. https://doi.org/10.1680/geot.1990.40.1.79.
Romo, M. P., and E. Ovando-Shelley. 1996. “Modelling the dynamic behaviour of Mexican clays.” In Proc., 11th World Conf. Earthquake Engineering, 1024. Oxford, UK: Pergamon Press.
Roscoe, K. H., and J. Burland. 1968. “On the generalized stress-strain behavior of wet clays.” In Engineering Plasticity, edited by J. Heyman and F. Leckie. Cambridge, UK: Cambridge University Press.
Saride, S., and T. Dutta. 2016. “Effect of fly-ash stabilization on stiffness modulus degradation of expansive clays.” J. Mater. Civil Eng. 28 (12): 04016166. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001678.
Sasanian, S., and T. A. Newson. 2014. “Basic parameters governing the behaviour of cement-treated clays.” Soils Found. 54 (2): 209–224. https://doi.org/10.1016/j.sandf.2014.02.011.
Subramaniam, P., and S. Banerjee. 2013. “Shear modulus degradation model for cohesive soils.” Soil Dyn. Earthquake Eng. 53 (Oct): 210–216. https://doi.org/10.1016/j.soildyn.2013.07.003.
Tatsuoka, F. 2006. “Inelastic deformation characteristics of geomaterial.” In Vol. 146 of Soil stress-strain behavior: Measurement, modeling and analysis, edited by H. I. Long, L. Callisto, D. Leschinsky, and J. Koseki, 26–133. Dordrecht, Netherlands: Springer.
Towhata, I. 2008. Geotechnical earthquake engineering. Berlin: Springer.
Tsai, P. H., and S. H. Ni. 2011. “A study on dynamic properties of cement-stabilized soils.” Adv. Mater. Res. 243–249: 2050–2054. https://doi.org/10.4028/www.scientific.net/AMR.243-249.2050.
Wang, D., N. Abriak, and R. Zentar. 2017. “Stress-dependent behavior of artificially structures and reconstituted marine soils.” Int. J. Geomech. 17 (4): 04016103. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000804.
Yang, L., and R. D. Woods. 2015. “Shear stiffness modeling of cemented clay.” Can. Geotech. J. 52 (2): 156–2015. https://doi.org/10.1139/cgj-2012-0377.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: Aug 3, 2018
Accepted: Jan 8, 2019
Published online: Apr 16, 2019
Published in print: Jul 1, 2019
Discussion open until: Sep 16, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.