Finite-Element Limit Analysis of Strip and Circular Skirted Footings on Sand
Publication: International Journal of Geomechanics
Volume 19, Issue 3
Abstract
The lower- and upper-bound theorems of the limit analysis have been used in conjunction with finite elements and second-order cone programming (SOCP) for determining the bearing capacity of strip and circular skirted footings on sand. The analysis follows the Mohr-Coulomb’s yield criterion and the associated flow rule; sand is not usually considered to obey this rule, but the results of using it are discussed. The friction angle of sand was varied between 30 and 45°, and the depth (Ds) of the skirt increased from 0.25 to 2B; here B implies: (1) the width of a skirted strip footing, and (2) the diameter of a circular skirted footing. The results are expressed in terms of the bearing capacity ratio (BCR): the ratio of the bearing capacities of a skirted footing to that of the surface footing, with the same value of B but without any skirt element. The results reveal that the magnitude of the BCR increases quite extensively with an increase in the value of Ds/B. The skirted footing was found to be especially quite advantageous for loose sand. With the same Ds/B, the BCR for a circular skirted footing was found to be substantially greater than that for the strip skirted footing.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The first author is grateful to the Indian Institute of Technology (ISM) Dhanbad for providing a grant under the faculty research scheme (FRS) for carrying out this research.
References
Al-Aghbari, M. Y. 2007. “Settlement of shallow circular foundations with structural skirts resting on sand.” J. Eng. Res. 4 (1): 11–16. https://doi.org/10.24200/tjer.vol4iss1pp11-16.
Al-Aghbari, M. Y., and R. K. Dutta. 2008. “Performance of square footing with structural skirt resting on sand.” Geomech. Geoeng. 3 (4): 271–277. https://doi.org/10.1080/17486020802509393.
Al-Aghbari, M. Y., and Y. E. A. Mohamedzein. 2004. “Bearing capacity of strip foundations with structural skirts.” Geotech. Geol. Eng. 22: 43–57. https://doi.org/10.1023/B:GEGE.0000013997.79473.e0.
Bolton, M. D. 1986. “The strength and dilatancy of sands.” Géotechnique 36 (1): 65–67. https://doi.org/10.1680/geot.1986.36.1.65.
Bowles, J. E. 1997. Foundation analysis and design. 5th ed. New York: McGraw-Hill, Inc.
Bransby, M. F., and M. F. Randolph. 1998. “Combined loading of skirted foundations.” Géotechnique 48 (5): 637–655. https://doi.org/10.1680/geot.1998.48.5.637.
Byrne, B. W., and G. T. Houlsby. 2002. “Experimental investigations of response of suction caissons to transient vertical loading.” J. Geotech. Geoenviron. Eng. 128 (11): 926–939. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:11(926).
Calladine, C. R. 2000. Plasticity for engineers: Theory and applications. 1st ed. Chichester: Horwood Publishing Limited.
Davis, E. H. 1968. “Theories of plasticity and the failure of soil masses.” In Soil mechanics: Selected topics, edited by I. K. Lee, 341–380. London: Butterworth’s.
Dewoolkar, M. M., J. Hwang, and H. Y. Ko. 2008. “Physical and finite element modeling of lateral stability of offshore skirted gravity structures subjected to iceberg impact load.” Ocean Eng. 35 (16): 1615–1626. https://doi.org/10.1016/j.oceaneng.2008.08.005.
Drescher, A., and E. Detournay. 1993. “Limit load in translational failure mechanisms for associative and non-associative materials.” Géotechnique 43 (3): 443–456. https://doi.org/10.1680/geot.1993.43.3.443.
Eid, H. T. 2013. “Bearing capacity and settlement of skirted shallow foundations on sand.” Int. J. Geomech. 13 (5): 645–652. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000237.
Eid, H. T., O. A. Alansari, A. M. Odeh, M. N. Nasr, and H. A. Sadek. 2009. “Comparative study on the behavior of square foundations resting on confined sand.” Can. Geotech. J. 46 (4): 438–453. https://doi.org/10.1139/T08-134.
Gourvenec, S., and K. Jensen. 2009. “Effect of embedment and spacing of cojoined skirted foundation systems on undrained limit states under general loading.” Int. J. Geomech. 9 (6): 267–279. https://doi.org/10.1061/(ASCE)1532-3641(2009)9:6(267).
Hjiaj, M., A. V. Lyamin, and S. W. Sloan. 2005. “Numerical limit analysis solutions for the bearing capacity factor Nγ.” Int. J. Solids Struct. 42 (5–6): 1681–1704. https://doi.org/10.1016/j.ijsolstr.2004.08.002.
Khatri, V. N., S. P. Debbarma, R. K. Dutta, and B. Mohanty. 2017a. “Pressure-settlement behavior of square and rectangular skirted footings resting on sand.” Geomech. Eng. 12 (4): 689–705. https://doi.org/10.12989/gae.2017.12.4.689.
Khatri, V. N., J. Kumar, and S. Akhtar. 2017b. “Bearing capacity of foundations with an inclusion of dense sand layer over loose sand strata.” Int. J. Geomech. 17 (10): 06017018. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000980.
Krabbenhøft, K., A. V. Lyamin, and S. W. Sloan. 2007. “Formulation and solution of some plasticity problems as conic programs.” Int. J. Solids Struct. 44 (5): 1533–1549. https://doi.org/10.1016/j.ijsolstr.2006.06.036.
Krabbenhøft, K., A. V. Lyamin, and S. W. Sloan. 2008. “Three-dimensional Mohr-Coulomb limit analysis using semidefinite programming.” Comm. Numer. Methods Eng. 24 (11): 1107–1119. https://doi.org/10.1002/cnm.1018.
Kumar, J. 2009. “The variation of Nγ with footing roughness using the method of characteristics.” Int. J. Numer. Anal. Methods Geomech. 33 (2): 275–284. https://doi.org/10.1002/nag.716.
Kumar, J., and M. Chakraborty. 2014. “Upper-bound axisymmetric limit analysis using the Mohr-Coulomb yield criterion, finite elements, and linear optimization.” J. Eng. Mech. 140 (12): 06014012. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000820.
Kumar, J., and V. N. Khatri. 2008a. “Effect of footing roughness on lower bound Nγ values.” Int. J. Geomech. 8 (3): 176–187. https://doi.org/10.1061/(ASCE)1532-3641(2008)8:3(176).
Kumar, J., and V. N. Khatri. 2008b. “Effect of footing width on bearing capacity factor Nγ for smooth strip footings.” J. Geotech. Geoenviron. Eng. 134 (9): 1299–1310. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:9(1299).
Kumar, J., and V. N. Khatri. 2011. “Bearing capacity factors of circular foundations for a general c-Φ soil using lower bound finite elements limit analysis.” Int. J. Numer. Anal. Methods Geomech. 35 (3): 393–405. https://doi.org/10.1002/nag.900.
Lyamin, A. V., R. Salgado, S. W. Sloan, and M. Prezzi. 2007. “Two- and three-dimensional bearing capacity of footings in sand.” Géotechnique 57 (8): 647–662. https://doi.org/10.1680/geot.2007.57.8.647.
Lyamin, A. V., and S. W. Sloan. 2002a. “Lower bound limit analysis using non-linear programming.” Int. J. Numer. Methods Eng. 55 (5): 573–611. https://doi.org/10.1002/nme.511.
Lyamin, A. V., and S. W. Sloan. 2002b. “Upper bound limit analysis using linear finite elements and non-linear programming.” Int. J. Numer. Anal. Methods Geomech. 26 (2): 181–216. https://doi.org/10.1002/nag.198.
Makrodimopoulos, A., and C. M. Martin. 2006. “Lower bound limit analysis of cohesive frictional materials using second-order cone programming.” Int. J. Numer. Methods Eng. 66 (4): 604–634. https://doi.org/10.1002/nme.1567.
Makrodimopoulos, A., and C. M. Martin. 2007. “Upper bound limit analysis using simplex strain elements and second-order cone programming.” Int. J. Numer. Anal. Methods Geomech. 31 (6): 835–865. https://doi.org/10.1002/nag.567.
Martin, C. M. 2005. “Exact bearing capacity calculations using the method of characteristics.” In Vol. 4 of Proc., 11th Int. Conf. of IACMAG, 441–450. Turin, Italy: IACMAG.
Meyerhof, G. G. 1963. “Some recent research on bearing capacity of foundations.” Can. Geotech. J. 1 (1): 16–26. https://doi.org/10.1139/t63-003.
Mohapatra, D., and J. Kumar. 2018. “Upper-bound finite-element limit analysis of axisymmetric problems for Mohr-Coulomb materials using semidefinite programming.” J. Eng. Mech. 144 (7): 04018046. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001472.
Schofield, A. N. 1980. “Cambridge geotechnical centrifuge operations.” Géotechnique 30 (3): 227–268. https://doi.org/10.1680/geot.1980.30.3.227.
Sloan, S. W. 1988. “Lower bound limit analysis using finite elements and linear programming.” Int. J. Numer. Anal. Methods Geomech. 12 (1): 61–77. https://doi.org/10.1002/nag.1610120105.
Sloan, S. W. 1989. “Upper bound limit analysis using finite elements and linear programming.” Int. J. Numer. Analytical Meth. Geomech. 13 (3): 263–282. https://doi.org/10.1002/nag.1610130304.
Sloan, S. W., and P. W. Kleeman. 1995. “Upper bound limit analysis using discontinuous velocity fields.” Comput. Methods Appl. Mech. Eng. 127 (1–4): 293–314. https://doi.org/10.1016/0045-7825(95)00868-1.
Veiskarami, M., J. Kumar, and F. Valikhah. 2014. “Effect of the flow rule on the bearing capacity of strip foundations on sand by the upper-bound limit analysis and slip lines.” Int. J. Geomech. 14 (3): 04014008. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000324.
Wakil, A. Z. EL. 2010. “Horizontal capacity of skirted circular shallow footings on sand.” Alex. Eng. J. 49 (4): 379–385. https://doi.org/10.1016/j.aej.2010.07.003.
Wakil, A. Z. EL. 2013. “Bearing capacity of Skirt circular footing on sand.” Alex. Eng. J. 52 (3): 359–364. https://doi.org/10.1016/j.aej.2013.01.007.
Yin, J. H., Y. J. Wang, and A. P. S. Selvadurai. 2001. “Influence of nonassociativity on the bearing capacity of a strip footing.” J. Geotech. Geoenv. Eng. 127 (11): 985–989. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:11(985).
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: Aug 18, 2017
Accepted: Sep 14, 2018
Published online: Jan 7, 2019
Published in print: Mar 1, 2019
Discussion open until: Jun 7, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.