Digital Image Processing on Segregation of Rubber Sand Mixture
Publication: International Journal of Geomechanics
Volume 18, Issue 10
Abstract
The segregation of rubber sand mixtures, when they form heaps, as observed by the method of digital image processing (DIP), is presented. Through segmenting the digital images into a binary picture, the DIP method enables material ingredients identification and three-dimensional mapping of mixture segregation. This helps reach a better understanding of mixture heterogeneity when incorporating artificial material into conventional geotechnical materials. To gain an insight into the mixture heterogeneity, the DIP results were used to validate a discrete element model, and the model was then used to examine the influence of particle properties on the segregation. The discrete element simulations showed that the particle density is critical in material segregation, and the segregation becomes more noticeable when the materials density ratio increases. This trend is restricted by increasing the interparticle surface roughness.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the Australian Government through the Australian Research Council.
References
Ahmed, I., and C. W. Lovell. 1993. “Rubber soils as lightweight geomaterials.” Transp. Res. Rec. 1422: 61–70. https://trid.trb.org/view/390302.
Ai, J. 2010. “Particle scale and bulk scale investigation of granular piles and silos.” Ph.D. thesis, College of Science and Engineering, Univ. of Edinburgh.
Altuhafi, F., C. O'Sullivan, and I. Cavarretta. 2013. “Analysis of an image-based method to quantify the size and shape of sand particles.” J. Geotech. Geoenviron. Eng. 139 (8): 1290–1307. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000855.
Anand, A., J. S. Curtis, C. R. Wassgren, B. C. Hancock, and W. R. Ketterhagen. 2010. “Segregation of cohesive granular materials during discharge from a rectangular hopper.” Granular Matter 12 (2): 193–200. https://doi.org/10.1007/s10035-010-0168-9.
ASTM. 1997. An unresolved riddle: Tire chips, two roadbeds, and spontaneous reactions. x>STP1275. West Conshohocken, PA: ASTM.
Aydemir, S., S. Keskin, and L. R. Drees. 2004. “Quantification of soil features using digital image processing (DIP) techniques.” Geoderma 119 (1-2): 1–8. https://doi.org/10.1016/S0016-7061(03)00218-0.
Bosscher, P. J., T. B. Edil, and S. Kuraoka. 1997. “Design of highway embankments using tire chips.” J. Geotech. Geoenviron. Eng 123 (4): 295–304. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:4(295).
Chen, C., G. R. McDowell, and N. H. Thom. 2014. “Investigating geogrid-reinforced ballast: Experimental pull-out tests and discrete element modelling.” Soils Found. 54 (1): 1–11. https://doi.org/10.1016/j.sandf.2013.12.001.
Chen, S., Z. Q. Yue, and L. G. Tham. 2004. “Digital image-based numerical modeling method for prediction of inhomogeneous rock failure.” Int. J. Rock Mech. Min. Sci. 41 (6): 939–957. https://doi.org/10.1016/j.ijrmms.2004.03.002.
Chung, Y.-C. 2006. “Discrete element modelling and experimental validation of a granular solid subject to different loading conditions.” Ph.D. thesis, College of Science and Engineering, Univ. of Edinburgh.
Cundall, P. A., and O. D. Strack. 1979. “A discrete numerical model for granular assemblies.” Geotech. 29 (1): 47–65. https://doi.org/10.1680/geot.1979.29.1.47.
Donald, M., and B. Roseman. 1962. “Mixing and demixing of solid particles. Part I: Mechanisms in a horizontal drum mixer.” Br. Chem. Eng. 7 (10): 749–752.
Evans, T. M., and J. R. Valdes. 2011. “The microstructure of particulate mixtures in one-dimensional compression: Numerical studies.” Granular Matter 13 (5): 657–669. https://doi.org/10.1007/s10035-011-0278-z.
Falagush, O., G. R. McDowell, and H.-S. Yu. 2015. “Discrete element modeling of cone penetration tests incorporating particle shape and crushing.” Int. J. Geomech. 15 (6): 04015003. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000463.
Foose, G. J., C. H. Benson, and P. J. Bosscher. 1996. “Sand reinforced with shredded waste tires.” J. Geotech. Eng. 122 (9): 760–767. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:9(760).
Garga, V. K., and V. O'Shaughnessy. 2000. “Tire-reinforced earthfill. Part 1: Construction of a test fill, performance, and retaining wall design.” Can. Geotech. J. 37 (1): 75–96. https://doi.org/10.1139/t99-084.
Humphrey, D. N., and W. P. Manion. 1992. “Properties of tire chips for lightweight fill.” In Grouting, soil improvement and geosynthetics, Geotechnical Special Publication 2, edited by R. H. Borden, R. O. Holtz, and I. Juran, 1344–1355. Reston, VA: ASCE.
IBM. 1990. “NTSC luminance/chrominance equation definition for digital systems.” IBM Tech. Disclosure Bull. 32 (10A): 208–209.
Indraratna, B., N. T. Ngo, C. Rujikiatkamjorn, and J. S. Vinod. 2012. “Behavior of fresh and fouled railway ballast subjected to direct shear testing: discrete element simulation.” Int. J. Geomech. 14 (1): 34–44. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000264.
Itasca. 2009. “PFC3D 4.0 user’s manual.” Minneapolis: Itasca Consulting Group, Inc.
Kawaguchi, T., T. Tanaka, and Y. Tsuji. 1992. “Numerical simulation of fluidized bed using the discrete element method: The case of spouting bed.” Trans. Jpn. Soc. Mech. Eng. Ser. B 58 (551): 2119–2125. https://doi.org/10.1299/kikaib.58.2119.
Kemeny, J. M., A. Devgan, R. M. Hagaman, and X. Wu. 1993. “Analysis of rock fragmentation using digital image processing.” J. Geotech. Eng. 119 (7): 1144–1160. https://doi.org/10.1061/(ASCE)0733-9410(1993)119:7(1144).
Kudrolli, A. 2004. “Size separation in vibrated granular matter.” Rep. Prog. Phys. 67 (3): 209–248. https://doi.org/10.1088/0034-4885/67/3/R01.
Kuerbis, R., and Y. P. Vaid. 1988. “Sand sample preparation-the slurry deposition method.” Soils Found. 28 (4): 107–118. https://doi.org/10.3208/sandf1972.28.4_107.
Lai, P.-Y., L.-C. Jia, and C. Chan. 1997. “Friction induced segregation of a granular binary mixture in a rotating drum.” Phys. Rev. Lett. 79 (25): 4994–4997. https://doi.org/10.1103/PhysRevLett.79.4994.
Lee, C., H. Shin, and J. S. Lee. 2014. “Behavior of sand–rubber particle mixtures: Experimental observations and numerical simulations.” Int. J. Numer. Anal. Methods Geomech. 38 (16): 1651–1663. https://doi.org/10.1002/nag.2264.
Liu, J., B. Yun, and C. Zhao. 2012. “Identification and validation of rolling friction models by dynamic simulation of sandpile formation.” Int. J. Geomech. 12 (4): 484–493. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000156.
Lőrincz, J., E. Imre, M. Gálos, Q. Trang, K. Rajkai, S. Fityus, and G. Telekes. 2005. “Grading entropy variation due to soil crushing.” Int. J. Geomech. 5 (4): 311–319. https://doi.org/10.1061/(ASCE)1532-3641(2005)5:4(311).
Manahiloh, K. N., B. Muhunthan, and W. J. Likos. 2016. “Microstructure-based effective stress formulation for unsaturated granular soils.” Int. J. Geomech. 16 (6): D4016006. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000617.
Masad, E., R. Taha, C. Ho, and T. Papagiannakis. 1996. “Engineering properties of tire/soil mixtures as a lightweight fill material.” Geotech. Test. J. 19 (3): 297–304. https://doi.org/10.1520/GTJ10355J.
Ottino, J., and D. Khakhar. 2000. “Mixing and segregation of granular materials.” Annu. Rev. Fluid Mech. 32 (1): 55–91. https://doi.org/10.1146/annurev.fluid.32.1.55.
Patil, U., J. R. Valdes, and T. M. Evans. 2010. “Swell mitigation with granulated tire rubber.” J. Mater. Civ. Eng. 23 (5): 721–727. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000229.
Poh, P. S., and B. B. Broms. 1995. “Slope stabilization using old rubber tires and geotextiles.” J. Perform. Constr. Facil. 9 (1): 76–79. https://doi.org/10.1061/(ASCE)0887-3828(1995)9:1(76).
Pohlman, N. A., B. L. Severson, J. M. Ottino, and R. M. Lueptow. 2006. “Surface roughness effects in granular matter: influence on angle of repose and the absence of segregation.” Phys. Rev. E: Stat. Nonlinear Soft Matter Phys. 73 (3 Pt 1): 031304. https://doi.org/10.1103/PhysRevE.73.031304.
Shi, D., A. A. Abatan, W. L. Vargas, and J. J. McCarthy. 2007. “Eliminating segregation in free-surface flows of particles.” Phys. Rev. Lett. 99 (14): 148001. https://doi.org/10.1103/PhysRevLett.99.148001.
Tsang, H.-H., S. H. Lo, X. Xu, and M. Neaz Sheikh. 2012. “Seismic isolation for low-to-medium-rise buildings using granulated rubber–soil mixtures: Numerical study.” Earthquake Eng. Struct. Dyn. 41 (14): 2009–2024. https://doi.org/10.1002/eqe.2171.
Villeneuve, M. C., M. S. Diederichs, and P. K. Kaiser. 2011. “Effects of grain scale heterogeneity on rock strength and the chipping process.” Int. J. Geomech. 12 (6): 632–647. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000194.
Watabe, Y., H. Shinsha, H. Yoneya, and C. Ko. 2014. “Description of partial sandy layers of dredged clay deposit using penetration resistance in installation of prefabricated vertical drains.” Soils Found. 54 (5): 1006–1017. https://doi.org/10.1016/j.sandf.2014.09.006.
Williams, J. C. 1976. “The segregation of particulate materials. A review.” Powder Technol. 15 (2): 245–251. https://doi.org/10.1016/0032-5910(76)80053-8.
Yang, R. Y., R. P. Zou, and A. B. Yu. 2000. “Computer simulation of the packing of fine particles.” Phys. Rev. E: Stat. Phys. Plasmas Fluids Relat. Interdiscip. Top. 62 (3 Pt B): 3900–3908.
Yoshimine, M., and R. Koike. 2005. “Liquefaction of clean sand with stratified structure due to segregation of particle size.” Soils Found. 45 (4): 89–98. https://doi.org/10.3208/sandf.45.4_89.
Yoshimoto, N., R. P. Orense, F. Tanabe, N. Kikkawa, M. Hyodo, and Y. Nakata. 2011. “Measurement of degree of saturation on model ground by digital image processing.” Soils Found. 51 (1): 167–177. https://doi.org/10.3208/sandf.51.167.
Yue, Z. Q., and I. Morin. 1996. “Digital image processing for aggregate orientation in asphalt concrete mixtures.” Can. J. Civ. Eng. 23 (2): 480–489. https://doi.org/10.1139/l96-052.
Zhou, Y. C., B. D. Wright, R. Y. Yang, B. H. Xu, and A. B. Yu. 1999. “Rolling friction in the dynamic simulation of sandpile formation.” Physica A 269 (2-4): 536–553. https://doi.org/10.1016/S0378-4371(99)00183-1.
Zhou, Y. C., B. D. Xu, A. B. Yu, and P. Zulli. 2001. “Numerical investigation of the angle of repose of monosized spheres.” Phys. Rev. E: Stat. Nonlinear Soft Matter Phys. 64 (2 Pt 1): 021301. https://doi.org/10.1103/PhysRevE.64.021301.
Zornberg, J. G., A. R. Cabral, and C. Viratjandr. 2004. “Behaviour of tire shred sand mixtures.” Can. Geotech. J. 41 (2): 227–241. https://doi.org/10.1139/t03-086.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Sep 6, 2017
Accepted: Apr 17, 2018
Published online: Aug 8, 2018
Published in print: Oct 1, 2018
Discussion open until: Jan 8, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.