Scale-Size Dependency of Intact Rock under Point-Load and Indirect Tensile Brazilian Testing
Publication: International Journal of Geomechanics
Volume 18, Issue 3
Abstract
The problem of scale-size dependency of the mechanical properties of intact rock has been extensively investigated with a particular focus on uniaxial compressive strength, whereas a limited number of studies have included point-load and tensile testing. Such mechanical properties, in particular tensile strength, are of fundamental importance in the hydraulic fracturing design process. Despite advancement in such experimental researches, analytical investigation has not attracted the same amount of attention. In this paper, the scale-size dependency of intact rock under point-load and indirect tensile testing conditions was studied experimentally and analytically using different rock types with various geological origins, including sedimentary, igneous, and metamorphic. From the comparison of the experimental results, it was concluded that all rock types follow the generalized size-effect concept where strength decreases with an increase in size. Also, it was confirmed that under indirect tensile testing with an increase in size, the failure of rock transfers from pure tension to a combination of shearing and tension. In addition, the applicability of different size-effect models (statistics, fracture energy, and multifractals) to experimental data was assessed. It was thus concluded that the models with two constants fit the point-load strength data more accurately. Also, it was found that the size-effect model based on fracture-energy theory provided the best fit to the tensile strength data, whereas the statistical size-effect model provided the least best fit.
Get full access to this article
View all available purchase options and get full access to this article.
References
Allison, G. B., and Hughes, M. W. (1978). “The use of environmental chloride and tritium to estimate total recharge to an unconfined aquifer.” Aust. J. Soil Res., 16(2), 181–195.
Andreev, G. E. (1991a). “A review of the Brazilian test for rock tensile strength determination. Part I: Calculation formula.” Min. Sci. Technol., 13(3), 445–456.
Andreev, G. E. (1991b). “A review of the Brazilian test for rock tensile strength determination. Part II: Contact conditions.” Min. Sci. Technol., 13(3), 457–465.
Aubertin, M., Li, L., and Simon, R. (2000). “A multiaxial stress criterion for short and long term strength of isotropic rock media.” Int. J. Rock Mech. Min. Sci., 37(8), 1169–1193.
Baecher, G. B., and Einstein, H. H. (1981). “Size effect in rock testing.” Geophys. Res. Lett., 8(7), 671–674.
Bahrani, N., and Kaiser, P. K. (2016). “Numerical investigation of the influence of specimen size on the unconfined strength of defected rocks.” Computers and Geotechnics, 77, 56–67.
Baud, P., Klein, E., and Wong, T. F. (2004). “Compaction localization in porous sandstone: Spatial evolution of damage and acoustic emission activity.” J. Struct. Geol., 26(4), 603–624.
Bažant, Z. P. (1984). “Size effect in blunt fracture: Concrete, rock, metal.” Eng. Mech., 518–535.
Bieniawski, Z. T. (1975). “The point load test in geotechnical practice.” Eng. Geol., 9(1), 1–11.
Bieniawski, Z. T., and Hawkes, I. (1978). “Suggested methods for determining tensile strength of rock materials.” Int. J. Rock Mech. Min. Sci., 15(3), 99–103.
Brady, B. H. G., and Brown, E. T. (2006). Rock mechanics: For underground mining, Springer, New York.
Broch, E., and Franklin, J. A. (1972). “The point-load strength test.” Int. J. Rock Mech. Min. Sci., 9(6), 669–697.
Brook, N. (1977). A method of overcoming both shape and size effects in point load testing, Rock Engineering, Geotech Society, Univ. of Newcastle, London, 53–70.
Brook, N. (1980). “Size correction for point load testing.” Int. J. Rock Mech. Min. Sci., 17(4), 231–235.
Brook, N. (1985). “The equivalent core diameter method of size and shape correction in point load testing.” Int. J. Rock Mech. Min. Sci., 22(2), 61–70.
Butenuth, C. (1997). “Comparison of tensile strength values of rocks determined by point load and direct tension tests.” Rock Mech. Rock Eng., 30(1), 65–72.
Çanakci, H., and Pala, M. (2007). “Tensile strength of basalt from a neural network.” Eng. Geol., 94(1–2), 10–18.
Carmichael, R. S. (1982). Handbook of physical properties of rocks, CRC Press, Boca Raton, FL.
Carpinteri, A. (1994). “Fractal nature of material microstructure and size effects on apparent mechanical properties.” Mech. Mater., 18(2), 89–101.
Carpinteri, A., Chiaia, B., and Ferro, G. (1995). “Size effects on nominal tensile strength of concrete structures: Multifractality of material ligaments and dimensional transition from order to disorder.” Mater. Struct., 28(6), 311–317.
Carpinteri, A., and Ferro, G. (1994). “Size effects on tensile fracture properties: A unified explanation based on disorder and fractality of concrete microstructure.” Mater. Struct., 27(10), 563–571.
Chang, C., Zoback, M. D., and Khaksar, A. (2006). “Empirical relations between rock strength and physical properties in sedimentary rocks.” J. Pet. Sci. Eng., 51(3–4), 223–237.
Darlington, W. J., Ranjith, P. G., and Choi, S. K. (2011). “The effect of specimen size on strength and other properties in laboratory testing of rock and rock-like cementitious brittle materials.” Rock Mech. Rock Eng., 44(5), 513–529.
Dhir, R. K., and Sangha, C. M. (1973). “Relationships between size, deformation and strength for cylindrical specimens loaded in uniaxial compression.” Int. J. Rock Mech. Min. Sci., 10(6), 699–712.
Ding, X., Zhang, L., Zhu, H., and Zhang, Q. (2014). “Effect of model scale and particle size distribution on PFC3D simulation results.” Rock Mech. Rock Eng., 47(6), 2139–2156.
Erarslan, N., and Williams, D. J. (2012). “Experimental, numerical and analytical studies on tensile strength of rocks.” Int. J. Rock Mech. Min. Sci., 49, 21–30.
Forbes, M., Masoumi, H., Saydam, S., and Hagan, P. (2015). “Investigation into the effect of length to diameter ratio on the point load strength index of Gosford sandstone.” Proc., 49th U.S. Rock Mechanics/Geomechanics Symp., American Rock Mechanics Association, San Francisco, pp. 478–488.
Franklin, J. A. (1985). “Suggested method for determining point load strength.” Int. J. Rock Mech. Min. Sci., 22(2), 51–60.
Gao, F., Stead, D., and Kang, H. (2014). “Numerical investigation of the scale effect and anisotropy in the strength and deformability of coal.” Int. J. Coal Geol., 136, 25–37.
Goodman, R. E. (1989). Introduction to rock mechanics, John Wiley & Sons, New York.
Greminger, M. (1982). “Experimental studies of the influence of rock anisotropy and size and shape effects in point-load testing.” Int. J. Rock Mech. Min. Sci., 19(5), 241–246.
Hawkins, A. B. (1998). “Aspects of rock strength.” Bull. Eng. Geol. Environ., 57(1), 17–30.
Hoek, E., and Brown, E. T. (1980). Underground excavations in rock, Institute of Mining and Metallurgy, London.
Hunt, D. D. (1973). “The influence of confining pressure on size effect.” Master’s thesis, Massachusetts Institute of Technology, Cambridge, MA.
ISRM (International Society for Rock Mechanics). (2007). “The complete suggested methods for rock characterization, testing and monitoring: 1974–2006 ISRM.” Suggested methods prepared by the commission on testing methods, Ulusay, R., and Hudson, J. A., eds., ISRM Turkish National Group, Kozan ofset, Ankara.
Jizba, D. (1991). “Mechanical and acoustical properties of sandstones and shales.” Ph.D. dissertation, Stanford Univ., Stanford, CA.
Klein, E., Baud, P., Reuschlé, T., and Wong, T. F. (2001). “Mechanical behaviour and failure mode of Bentheim sandstone under triaxial compression.” Phys. Chem. Earth, 26(1–2), 21–25.
Komurlu, E., and Kesimal, A. (2015). “Evaluation of indirect tensile strength of rocks using different types of jaws.” Rock Mech. Rock Eng., 48(4), 1723–1730.
Kwasniewski, M. (1989). “Laws of brittle failure and of B-D transition in sandstones. Rock at great depth.” Proc., ISRM-SPE International Symp., A.A. Balkema, Rotterdam, Netherlands.
Lama, R., and Vutukuri, V. (1978). Handbook on mechanical properties of rock, Trans Tech Publications, Clausthal, Germany.
Masoumi, H. (2013). “Investigation into the mechanical behaviour of intact rock at different sizes.” Ph.D. thesis, Univ. of New South Wales Australia, Sydney, Australia.
Masoumi, H., Bahaaddini, M., Kim, G., and Hagan, P. (2014). “Experimental investigation into the mechanical behavior of Gosford sandstone at different sizes.” Proc., 48th U.S. Rock Mechanics/Geomechanics Symp., American Rock Mechanics Association, Minneapolis, pp. 1210–1215.
Masoumi, H., Douglas, K., and Russell, A. R. (2016a). “A bounding surface plasticity model for intact rock exhibiting size-dependent behaviour.” Rock Mech. Rock Eng., 49(1), 47–62.
Masoumi, H., Douglas, K., Saydam, S., and Hagan, P. (2012). “Experimental study of size effects of rock on UCS and point load tests.” Proc., 46th U.S. Rock Mechanics Geomechanics Symp., American Rock Mechanics Association, Chicago, 2561–2568.
Masoumi, H., Roshan, H., and Hagan, P. C. (2017a). “Size-dependent Hoek-Brown failure criterion.” Int. J. Geomech., 04016048.
Masoumi, H., Saydam, S., and Hagan, P. C. (2016b). “Incorporating scale effect into a multiaxial failure criterion for intact rock.” Int. J. Rock Mech. Min. Sci., 83, 49–56.
Masoumi, H., Saydam, S., and Hagan, P. C. (2016c). “Unified size-effect law for intact rock.” Int. J. Geomech., 04015059.
Masoumi, H., Serati, M., Williams, D. J., and Alehossein, H. (2017b). “Size dependency of intact rocks with high brittleness: A potential solution to eliminate secondary fractures in Brazilian test.” Proc., 51st U.S. Rock Mechanics/Geomechanics Symp., American Rock Mechanics Association, San Francisco.
Melean, Y., Washburn, K. E., Callaghan, P. T., and Arns, C. H. (2009). “A numerical analysis of NMR pore-pore exchange measurements using micro X-ray computed tomography.” Diffus. Fundam., 10(30), 1–3.
Mogi, K. (1962). “The influence of dimensions of specimens on the fracture strength of rocks.” Bull. Earth Res. Inst., 40, 175–185.
Murray-Wallace, C. V., Belperio, A. P., Bourman, R. P., Cann, J. H., and Price, D. M. (1999). “Facies architecture of a last interglacial barrier: A model for quaternary barrier development from the Coorong to Mount Gambier Coastal Plain, southeastern Australia.” Mar. Geol., 158(1–4), 177–195.
Quiñones, J., Arzúa, J., Alejano, L. R., García-Bastante, F., Mas Ivars, D., and Walton, G. (2017). “Analysis of size effects on the geomechanical parameters of intact granite samples under unconfined conditions.” Acta Geotechnica, 12(6), 1229–12429.
Roshan, H., et al. (2016a). “Total porosity of tight rocks: A welcome to heat transfer technique.” Energy Fuels, 30(12), 10072–10079.
Roshan, H., et al. (2018). “Microstructural effects on mechanical properties of shaly sandstone.” J. Geotech. Geoenviron. Eng., 06017019.
Roshan, H., Masoumi, H., and Hagan, P. (2016b). “On size-dependent uniaxial compressive strength of sedimentary rocks in reservoir geomechanics.” Proc., 50th U.S. Rock Mechanics/Geomechanics Symp., American Rock Mechanics Association, Houston, pp. 2322–2327.
Roshan, H., Masoumi, H., and Regenauer-Lieb, K. (2017). “Frictional behaviour of sandstone: A sample-size dependent triaxial investigation.” J. Struct. Geol., 94, 154–165.
Russell, A. R., and Muir Wood, D. (2009). “Point load tests and strength measurements for brittle spheres.” Int. J. Rock Mech. Min. Sci., 46(2), 272–280.
Savidis, G. M. (1982). “Fundamental studies on the excavation of rock by button cutter.” Ph.D. thesis, Univ. of New South Wales, Sydney, Australia.
Serati, M. (2014). “Stiffness and strength of rock cutting and drilling tools: Drag bit and roller disc cutters.” Ph.D. thesis, Univ. of Queensland, Brisbane, Australia.
Serati, M., Alehossein, H., and Williams, D. J. (2015). “Estimating the tensile strength of super hard brittle materials using truncated spheroidal specimens.” J. Mech. Phys. Solids, 78, 123–140.
Thuro, K., Plinninger, R. J., Zah, S., and Schutz, S. (2001a). “Scale effect in rock strength properties. Part 1: Unconfined compressive test and Brazilian test.” Rock mechanics: A challenge for society, Zeitlinger, Lisse, Switzerland, 169–174.
Thuro, K., Plinninger, R. J., Zah, S., and Schutz, S. (2001b). “Scale effect in rock strength properties. Part 2: Point load test and point load strength index.” Rock mechanics: A challenge for society, Zeitlinger, Lisse, Switzerland, 175–180.
Wang, S. Y., Sloan, S. W., and Tang, C. A. (2014). “Three-dimensional numerical investigations of the failure mechanism of a rock disc with a central or eccentric hole.” Rock Mech. Rock Eng., 47(6), 2117–2137.
Weibull, W. (1939). A statistical theory of the strength of materials, Royal Swedish Academy of Engineering Science, Stockholm, Sweden, 1–45.
Weibull, W. (1951). “A statistical distribution of function of wide applicability.” J. Appl. Mech., 18, 293–297.
Wijk, G. (1978). “Some new theoretical aspects of indirect measurements of the tensile strength of rocks.” Int. J. Rock Mech. Min. Sci., 15(4), 149–160.
Wong, L. N. Y., and Zhang, X. P. (2014). “Size effects on cracking behavior of flaw-containing specimens under compressive loading.” Rock Mech. Rock Eng., 47(5), 1921–1930.
Wong, T. F., David, C., and Zhu, W. (1997). “The transition from brittle faulting to cataclastic flow in porous sandstones: Mechanical deformation.” J. Geophys. Res.: Solid Earth, 102(B2), 3009–3025.
Yoshinaka, R., Osada, M., Park, H., Sasaki, T., and Sasaki, K. (2008). “Practical determination of mechanical design parameters of intact rock considering scale effect.” Eng. Geol., 96(3–4), 173–186.
Yu, Y., Yin, J., and Zhong, Z. (2006). “Shape effects in the Brazilian tensile strength test and a 3D FEM correction.” Int. J. Rock Mech. Min. Sci., 43(4), 623–627.
Zhang, Q., Zhu, H., Zhang, L., and Ding, X. (2011). “Study of scale effect on intact rock strength using particle flow modeling.” Int. J. Rock Mech. Min. Sci., 48(8), 1320–1328.
Zhang, X. P., Wong, L. N. Y., and Wang, S. (2015). “Effects of the ratio of flaw size to specimen size on cracking behavior.” Bull. Eng. Geol. Environ., 74(1), 181–193.
Zoback, M. D. (2007). Reservoir geomechanics, University Press, Cambridge, U.K.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 18 • Issue 3 • March 2018
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Mar 1, 2017
Accepted: Sep 28, 2017
Published online: Jan 11, 2018
Published in print: Mar 1, 2018
Discussion open until: Jun 11, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.