Porosity and Permeability Alteration around Wellbore during Injection Process
Publication: International Journal of Geomechanics
Volume 18, Issue 2
Abstract
Enhanced oil recovery (EOR) methods were processed to increase the amount of oil extracted from a reservoir after primary and secondary recoveries, typically by injecting water or gas. Fluid injection has been vastly applied in oil wells as a simple and effective EOR method. Rocks are a combination of different materials that exhibit poroelastic response. The amount of stress indexed by pore pressure depends on pore content. Rock stress around a wellbore is a function of wellbore fluid flow. On the other hand, fluid flow is the function of porosity and permeability. Nevertheless, porosity and permeability alter as stress changes. Therefore, a coupling method should be used. The purpose of this study is to propose a model to find corrected stresses and calculate the change in porosity and permeability after injection. This study focuses on wellbore results. Effective parameters, such as pressure, temperature, saturation, and stress, were obtained for the multiphase flow condition using mathematical modeling. Moreover, pressure and saturation are solved using the finite-difference method, whereas the finite-volume method is applied to obtain rock stresses. The iterative coupling method is used to improve the accuracy of results. The results of the study showed how porosity and permeability will change after drilling around the well and how they will increase during injection. The results expressed the corrected distribution of stress values after injection. Porosity and permeability were reduced from their original values after drilling; nonetheless, their values had increased after injection but not equally around the wellbore. Moreover, it was concluded that the change in porosity and permeability by injection was more significant in low-porosity formations.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abaqus 6.10 [Computer software]. SIMULIA, Providence, RI.
Bataee, M., and Irawan, S. (2014). “Review of geomechanical application in reservoir modeling.” J. Appl. Sci.,14(10), 981–990.
Bataee, M., Irawan, S., and Majidaie, S. (2014). “The effects of geomechanics on the WAG injection model.” Proc., Offshore Technology Conf. Asia, Offshore Technology Conf.,Society of Petroleum Engineers, Richardson, TX.
Bataee, M., Irawan, S., Namazi-Saleh, F., and Ridha, S. (2017). “Development of stress model near the wellbore using an iterative coupling method.” Int. J. Geomech., 04016047.
Chen, Z., Huan, G., and Ma, Y. (2006). Computational methods for multiphase flows in porous media,SIAM,Philadelphia.
Chenevert, M., and Sharma, A. (1993). “Permeability and effective pore pressure of shales.” SPE Drill. Complet.,8(1), 28–34.
Chiaramonte, L. (2009). “Geomechanical characterization and reservoir simulation of a carbon dioxide sequestration project in a mature oil field.” Ph.D. thesis,Stanford Univ.,Stanford, CA.
Chin, L., Thomas, L., Sylte, J., and Pierson, R. (2002). “Iterative coupled analysis of geomechanics and fluid flow for rock compaction in reservoir simulation.” Oil Gas Sci. Technol.,57(5), 485–497.
Dean, R. H., Gai, X., Stone, C. M., and Minkoff, S. E. (2006). “A comparison of techniques for coupling porous flow and geomechanics.” SPE J.,11(1), 132–140.
Dezfooli, M. S., Abolmaali, A., and Razavi, M. (2015). “Coupled nonlinear finite-element analysis of soil-steel pipe structure interaction.” Int. J. Geomech., 04014032.
Fjar, E., Holt, R. M., Raaen, A. M., Risnes, R., and Horsrud, P. (2008). Petroleum related rock mechanics,Elsevier,Amsterdam, Netherlands.
FLAC3D [Computer software]. Itasca Consulting Group, Minneapolis.
Fredrich, J. T., Arguello, J., Deitrick, G., and De Rouffignac, E. (2000). “Geomechanical modeling of reservoir compaction, surface subsidence, and casing damage at the Belridge diatomite field.” SPE Reservoir Eval. Eng.,3, 348–359.
Ghabezloo, S., Sulem, J., and Saint-Marc, J. (2009). “Evaluation of a permeability–porosity relationship in a low-permeability creeping material using a single transient test.” Int. J. Rock Mech. Min. Sci.,46(4), 761–768.
Gong, J., Polikar, M., and Chalaturnyk, R. (2002). “Fast SAGD and geomechanical mechanisms.” Proc., Canadian Int. Petroleum Conf.,Society of Petroleum Engineers, Richardson, TX.
Hansen, K., Prats, M., and Chan, C. (1995). “Modeling of reservoir compaction and surface subsidence at South Belridge.” SPE Prod. Facil.,10(3), 134–143.
Irawan, S., and Bathaee, M. (2015). “Numerical modeling of flow and temperature distribution in heterogeneous wellbore medium.” Proc., SPE Middle East Oil & Gas Show and Conf.,Society of Petroleum Engineers,Richardson, TX.
Lewis, R., Roberts, P., and Schrefler, B. (1989). “Finite element modelling of two-phase heat and fluid flow in deforming porous media.” Transp. Porous Media,4(4), 319–334.
Li, K. (2008). “A new method for calculating two-phase relative permeability from resistivity data in porous media.” Transp. Porous Media,74(1), 21–33.
MATLAB R2013a [Computer software]. MathWorks, Natick, MA.
Palmer, I., and Mansoori, J. (1996). “How permeability depends on stress and pore pressure in coalbeds: A new model.” Proc., SPE Annual Technical Conf. and Exhibition, Society of Petroleum Engineers, Richardson, TX, 539–544.
Pao, W. K., Lewis, R. W., and Masters, I. (2001). “A fully coupled hydro‐thermo‐poro‐mechanical model for black oil reservoir simulation.” Int. J. Numer. Anal. Methods Geomech.,25(12), 1229–1256.
Pattillo, P., Kristiansen, T., Sund, G., and Kjelstadli, R., (1998). “Reservoir compaction and seafloor subsidence at Valhall.” Proc., SPE/ISRM Rock Mechanics in Petroleum Engineering, Society of Petroleum Engineers, Richardson, TX,1, 377–386.
Qobi, L., Strauss, J. P., Alexander, D. M., Thang, M., and Al Kindy, F. (2010). “EOR geomechanical screening; identification of risks to mitigate and opportunities to pursue.” Proc., SPE EOR Conf. at Oil & Gas West Asia,Society of Petroleum Engineers,Richardson, TX.
Rahman, M., and Rahman, S. (2013). “Fully coupled finite-element–based numerical model for investigation of interaction between an induced and a preexisting fracture in naturally fractured poroelastic reservoirs: Fracture diversion, arrest, and breakout.” Int. J. Geomech., 390–401.
Rutqvist, J., Vasco, D. W., and Myer, L. (2010). “Coupled reservoir-geomechanical analysis of CO2 injection and ground deformations at In Salah, Algeria.” Int. J. Greenhouse Gas Control,4(2), 225–230.
TOUGH 2 [Computer software]. Lawrence Berkeley National Laboratory, Energy Geosciences Division, Berkeley, CA.
Tran, D., Nghiem, L., and Buchanan, L. (2005). “Improved iterative coupling of geomechanics with reservoir simulation.” Proc., SPE Reservoir Simulation Symp.,Society of Petroleum Engineers,Richardson, TX.
Wan, R., and Wang, J. (2004). “Analysis of sand production in unconsolidated oil sand using a coupled erosional-stress-deformation model.” J. Can. Pet. Technol.,43(2), 47–53.
Zhai, Z., and Abou-Sayed, A. S. (2011). “Thermal-poro plastic stress effect on stress reorientation in production and injection wells.” Proc., Brasil Offshore,Society of Petroleum Engineers,Richardson, TX.
Zoback, M. D., and Byerlee, J. (1975). “Permeability and effective stress: Geologic notes.” AAPG Bull.,59, 154–158.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 18 • Issue 2 • February 2018
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Feb 23, 2017
Accepted: Aug 3, 2017
Published online: Dec 4, 2017
Published in print: Feb 1, 2018
Discussion open until: May 4, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.