Bearing Capacity of Rectangular Footings on Multilayer Geosynthetic-Reinforced Granular Fill over Soft Soil
Publication: International Journal of Geomechanics
Volume 17, Issue 9
Abstract
In the present study, the bearing capacity of rectangular footings resting on multilayer geosynthetic-reinforced granular fill overlying soft soil is investigated. Five different sizes of model footings are chosen in such a way that the aspect ratio of the footings is varied as 1.0 (square), 1.5 (rectangular), and 2.0 (rectangular). The effectiveness of multilayer reinforcement is assessed by comparing the bearing capacity improvement factor, settlement reduction factor, and load-spread angle. The variations of these factors with the aspect ratio of the footings are also studied. The optimum value of the thickness of granular fill over soft soil and sizes of the reinforcement as obtained for single-layer reinforcement placed at the granular fill-clay interface are selected for the entire test program. In some of the model tests, the reinforcement layers are instrumented with strain gauges to study the strain distribution along the reinforcement layers. The test results show that the improvement factor and settlement reduction increase with a decrease in the aspect ratio of the footing, and the increment is more for the multilayer-reinforced case (N > 1). However, the increment is more for the constant width case than with the constant length case of the footing. The load-spread angle increases with an increase of the L/B ratio of the rectangular footings, and the rate of increment decreases due to an increase in the number of reinforcement. An analytical solution is also proposed to estimate the ultimate bearing capacity of rectangular footings with various aspect ratios resting on the multilayer geosynthetic-reinforced granular fill of limited thickness underlain by soft soil. The predictions of the bearing capacity made by the developed model are found to be in good agreement with the experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abu-Farsakh, M., Chen, Q., and Sharma, R. (2013). “An experimental evaluation of the behavior of footings on geosynthetic-reinforced sand.” Soils Found., 53(2), 335–348.
Abu-Farsakh, M., Chen, Q., Sharma, R., and Zhang, X. (2008). “Large-scale model footing tests on geogrid reinforced marginal embankment soil.” Geotech. Test. J., 31(5), 413–423.
Adams, M., and Collin, J. (1997). “Large model spread footing load tests on geosynthetic reinforced soil foundations.” J. Geotech. Geoenviron. Eng., 66–72.
Alawaji, H. A. (2001). “Settlement and bearing capacity of geogrid-reinforced sand over collapsible soil.” Geotext. Geomembr., 19(2), 75–88.
Alenowicz, J., and Dembicki, E. (1991). “Recent laboratory research on unpaved road behaviour.” Geotext. Geomembr., 10(1), 21–34.
Ambily, A., and Gandhi, S. (2007). “Behavior of stone columns based on experimental and FEM analysis.” J. Geotech. Geoenviron. Eng., 405–415.
Binquet, J., and Lee, K. L. (1975a). “Bearing capacity analysis of reinforced earth slabs.” J. Geotech. Eng. Div., 101(12), 1257–1276.
Binquet, J., and Lee, K. L. (1975b). “Bearing capacity tests on reinforced earth slabs.” J. Geotech. Eng. Div., 101(12), 1241–1255.
Brand, E. W., Muktabhant, C., and Taechathummarak, A. (1972). “Load tests on small foundations in soft clay.” Proc., Performance of Earth and Earth-Supported Structures, 1(2), ASCE, Reston, VA, 903–928.
Briaud, J. L., and Jeanjean, P. (1994). “Load settlement curve method for footings on sand.” Proc., Settlement 94, Vertical and horizontal deformations of foundations and embankments, Vol. 2, ASCE, Reston, VA, 1774–1804.
Burd, H. J. (1995). “Analysis of membrane action in reinforced unpaved road.” Can. Geotech. J., 32(6), 946–956.
Chen, Q. (2007). “An experimental study on characteristics and behavior of reinforced soil foundation.” Ph.D. dissertation, Louisiana State Univ., Baton Rouge, LA.
Chen, Q., and Abu-Farsakh, M. (2015). “Ultimate bearing capacity analysis of strip footings on reinforced soil foundation.” Soils Found., 55(1), 74– 85.
Chen, Q., Abu-Farsakh, M., and Sharma, R. (2009). “Experimental and analytical studies of reinforced crushed limestone.” Geotext. Geomembr., 27(5), 357–367.
Consoli, N., Rosa, F., and Fonini, A. (2009). “Plate load tests on cemented soil layers overlaying weaker soil.” J. Geotech. Geoenviron. Eng., 1846–1856.
Das, B. M. (1989). “Foundation on sand underlain by a soft clay with geotextile at sand-clay interface.” Proc., Geosynthetics ’89 Conf., Industrial Fabrics Association International, Roseville, MN, 203–213.
Das, B. M., Puri, V. K., and Neo, B. K. (1993). “Interference effects between two surface footings on layered soil.” Transportation Research Record, 1406, 34–40.
Dash, S. K., and Bora, M. C. (2013). “Improved performance of soft clay foundations using stone columns and geocell-sand mattress.” Geotext. Geomembr., 41(Nov), 26–35.
Dash, S. K., Sireesh, S., and Sitharam, T. G. (2003). “Model studies on circular footing supported on geocell reinforced sand underlain by soft clay.” Geotext. Geomembr., 21(4), 197–219.
Deb, K., Chandra, S., and Basudhar, P. K. (2005). “Settlement response of a multilayer geosynthetic-reinforced granular fill-soft soil system.” Geosynth. Int., 12(6), 288–298.
Deb, K., Samadhiya, N. K., and Namdeo, J. B. (2011). “Laboratory model studies on unreinforced and geogrid-reinforced sand bed over stone column-improved soft clay.” Geotext. Geomembr., 29(2), 190–196.
Deb, K., Sivakugan, N., Chandra, S., and Basudhar, P. K. (2007). “Numerical analysis of multi layer geosynthetic-reinforced granular bed over soft fill.” Geotech. Geol. Eng., 25(6), 639–646.
Demir, A., Laman, A., Yildiz, A., and Ornek, M. (2013). “Large scale field tests on geogrid reinforced granular fill underlain by clay soil.” Geotext. Geomembr., 38(Jun), 1–15.
Demir, A., Yildiz, A., Laman, M., and Ornek, M. (2014). “Experimental and numerical analyses of circular footing on geogrid-reinforced granular fill underlain by soft clay.” Acta Geotech., 9(4), 711–723.
Ghosh, C., and Madhav, M. R. (1994). “Reinforced granular fill-soft soil system: Membrane effect.” Geotext. Geomembr., 13(11), 743–759.
Giroud, J. P. (1992). “Biaxial tensile state of stress in geosynthetics.” Geotext. Geomembr., 11(3), 319–325.
Giroud, J. P. (1995). “Determination of geosynthetic strain due to deflection.” Geosynth. Int., 2(3), 635–641.
Giroud, J. P., and Noiray, L. (1981). “Geotextile reinforced unpaved road design.” J. Geotech. Eng. Div., 107(9), 1233–1254.
Gnanendran, C. T., and Selvadurai, A. P. S. (2001). “Strain measurement and interpretation of stabilising force in geogrid reinforcement.” Geotext. Geomembr., 19(3), 177–194.
Guido, V. A., Chang, D. K., and Sweeney, M. A. (1986). “Comparison of geogrid and geotextile reinforced slabs.” Can. Geotech. J., 23(4), 435–440.
Huang, C. C., and Tatsuoka, F. (1990). “Bearing capacity of reinforced horizontal sandy ground.” Geotext. Geomembr., 9(1), 51–82.
Ilamparuthi, K., and Muthukrishnaiah, K. (1999). “Anchors in sand bed: Delineation of rupture surface.” Ocean Eng., 26(12), 1249–1273.
Khing, K. H., Das, B. M., Puri, V. K., Yen, S. C., and Cook, E. E. (1994). “Foundation on strong sand underlain by weak clay with geogrid at the interface.” Geotext. Geomembr., 13(3), 199–206.
Kumar, A., and Saran, S. (2003). “Bearing capacity of rectangular footing on reinforced soil.” Geotech. Geol. Eng., 21(3), 201–224.
Lee, K. M., Manjunath, V. R., and Dewaikar, D. M. (1999). “Numerical and model studies of strip footing supported by a reinforced granular fill-soft soil system.” Can. Geotech. J., 36(5), 793–806.
Love, J. P., Burd, H. J., Milligan, G. W. E., and Houlsby, G. T. (1987). “Analytical and model studies of reinforcement of a layer of granular fill on a soft clay subgrade.” Can. Geotech. J., 24(4), 611–622.
Madhav, M. R., and Poorooshasb, H. B. (1988). “A new model for geosynthetic-reinforced soil.” Comput. Geotech., 6(4), 277–290.
Mandal, J. N., and Sah, H. S. (1992). “Bearing capacity tests on geogrid-reinforced clay.” Geotext. Geomembr., 11(3), 327–333.
Meyerhof, G. G. (1951). “The ultimate bearing capacity of foundations.” Géotechnique, 2(4), 301–332.
Meyerhof, G. G. (1963). “Some recent research on the bearing capacity of foundations.” Can. Geotech. J., 1(1), 16–26.
Meyerhof, G. G., and Hanna, A. M. (1978). “Ultimate bearing capacity of foundations on layered soils under inclined load.” Can. Geotech. J., 15(4), 565–572.
Michalowski, R. (2004). “Limit loads on reinforced foundation soils.” J. Geotech. Geoenviron. Eng., 381–390.
Okamura, M., Takemura, J., and Kimura, T. (1997). “Centrifuge model tests on bearing capacity and deformation of sand layer overlying clay.” Soils Found., 37(1), 73–88.
Okamura, M., Takemura, J., and Kimura, T. (1998). “Bearing capacity predictions of sand overlying clay based on limit equilibrium methods.” Soils Found., 38(1), 181–194.
Omar, M. T., Das, B. M., Puri, V. K., and Yen, S. C. (1993a). “Ultimate bearing capacity of shallow foundations on sand with geogrid reinforcement.” Can. Geotech. J., 30(3), 545–549.
Omar, M. T., Das, B. M., Yen, S. C., Puri, V. K., and Cook, E. E. (1993b). “Ultimate bearing capacity of rectangular foundations on geogrid-reinforced sand.” Geotech. Test. J., 16(2), 246–252.
Palmeira, E. M., and Cunha, M. G. (1993). “A study of the mechanics of unpaved roads with reference to the effects of surface maintenance.” Geotext. Geomembr., 12(2), 109–131.
Saha Roy, S. M., and Deb, K. (2017). “Effects of aspect ratio of footings on bearing capacity for geogrid-reinforced sand over soft soil.” Geosynth. Int., in press.
Sawwaf, M. (2009). “Experimental and numerical study of eccentrically loaded strip footings resting on reinforced sand.” J. Geotech. Geoenviron. Eng., 1509–1518.
Schmertmann, J. H., Hartman, J. P., and Brown, P. R. (1978). “Improved strain influence factor diagrams.” J. Geotech. Eng. Div., 104(GT8), 1131–1135.
Sharma, R., Chen, Q., Farsakh, M. A., and Yoon, S. (2009). “Analytical modeling of geogrid reinforced soil foundation.” Geotext. Geomembr., 27(1), 63–72.
Shin, E. C., Das, B. M., Puril, V. K., Yen, S. C., and Cook, E. E. (1993). “Bearing capacity of strip foundation on geogrid reinforced clay.” Geotech. Test. J., 16(4), 534–541.
Shivashankar, R., and Jayaraj, J. (2014). “Effects of prestressing the reinforcement on the behavior of reinforced granular beds overlying weak soil.” Geotext. Geomembr., 42(1), 69–75.
Shukla, S. K., and Chandra, S. (1995). “Modelling of geosynthetic-reinforced engineered granular fill on soft soil.” Geosynth. Int., 2(3), 603–617.
Sitharam, T. G., and Hegde, A. (2013). “Design and construction of geocell foundation to support the embankment on settled red mud.” Geotext. Geomembr., 41(Nov), 55–63.
Tafreshi, S. N. M., and Dawson, A. R. (2010). “Comparison of bearing capacity of a strip footing on sand with geocell and with planar forms of geotextile reinforcement.” Geotext. Geomembr., 28(1), 72–84.
Vesic, A. S. (1973). “Analysis of ultimate loads of shallow foundations.” J. Soil Mech. Found. Div., 99(SM1), 45–73.
Vesic, A. S. (1975). “Bearing capacity of shallow foundations.” Foundation engineering handbook, 1st Ed., H. F. Winterkorn and H. Y. Fang, eds., Van Nostrand Reinhold, New York, 121–147.
Wayne, M. H., Han, J., and Akins, K. (1998). “The design of geosynthetic reinforced foundations.” 1998 Annual Convention & Exposition, Geotechnical special publication, 76, ASCE, Reston, VA, 1–18.
Yetimoglu, T., Wu, J., and Saglamer, A. (1994). “Bearing capacity of rectangular footings on geogrid-reinforced sand.” J. Geotech. Eng., 2083–2099.
Yin, J. H. (1997). “Modelling geosynthetic-reinforced granular fills over soft soil.” Geosynth. Int., 4(2), 165–185.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 17 • Issue 9 • September 2017
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Aug 29, 2016
Accepted: Mar 10, 2017
Published online: Jun 9, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 9, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.