Validation of GPD to Model Rock Fragmentation by TBM Cutters
Publication: International Journal of Geomechanics
Volume 17, Issue 6
Abstract
In this paper, a novel meshless numerical method known as general particle dynamics (GPD) is developed to reveal the mechanism of the rock fragmentation using tunnel-boring machine (TBM) cutters. Rock fragmentation by one cutter and by two cutters is investigated using GPD. The numerical results obtained from GPD well agree with the previous experimental and numerical results. Moreover, the effects of arrays of flaws on rock fragmentation are also studied using GPD as well as stress fields and rock fragmentation efficiency. It is found from the numerical results that arrays of flaws significantly influence the drivage efficiency of rock fragmentation as well as the depth of chipping and the coalescence modes of flaws.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by Project 973 (Grant 2014CB046903), the National Natural Science Foundation of China (51325903 and 51279218), the Natural Science Foundation Project of CQ CSTC (CSTC, cstc2013kjrcljrccj0001, CSTC, and cstc2016jcyjys0005; CSTC, cstc2015jcyjys0002, CSTC, and cstc2015jcyjys0009), the research fund by the Doctoral Program of Higher Education of China (20130191110037), and the Graduate Scientific Research and Innovation Foundation of Chongqing, China (Grant CYB16012).
References
Antolini, F., Barla, M., Gigli, G., Giorgetti, A., Intrieri, E., and Casagli, N. (2016). “Combined finite-discrete numerical modeling of runout of the Torgiovannetto di Assisi rockslide in central Italy.” Int. J. Geomech., 04016019.
Barla, M., and Beer, G. (2012). “Special issue on advances in modeling rock engineering problems.” Int. J. Geomech., 617–617.
Bejari, H., and Hamidi, J. K. (2013). “Simultaneous effects of joint spacing and orientation on TBM cutting efficiency in jointed rock masses.” Rock Mech. Rock Eng., 46(4), 897–907.
Bi, J., and Zhou, X. P. (2015). “Numerical simulation of zonal disintegration of the surrounding rock masses around a deep circular tunnel under dynamic unloading.” Int. J. Comput. Methods, 12(3), 1550020.
Bouchard, P. O., Baya, F., Chastel, Y., and Toven, I. (2000). “Crack propagation modelling using an advanced remeshing technique.” Comput. Methods Appl. Mech. Eng., 189(3), 723–742.
Boussinesq, J. (1885). “Sur la résistance qu’oppose un fluide indéfini au repos sans pesanteur au mouvement varié d’une sphère solide qu’il mouille sur toute sa surface quand les vitesses restent bien continues et assez faibles pour que leurs carrés et produits soient négligeables.” C.R. Acad. Sci. Paris, 100, 935–937.
Bruland, A. (2000). “Hard rock tunnel boring.” Doctoral thesis, Norwegian Univ. of Science and Technology, Trondheim, Norway.
Camusso, M., and Barla, M. (2009). “Microparameters calibration for loose and cemented soil when using particle methods.” Int. J. Geomech., 217–229.
Chen, L. H., and Labuz, J. F. (2006). “Indentation of rock by wedge-shaped tools.” Int. J. Rock Mech. Min., 43(7), 1023–1033.
Chiaia, B. (2001). “Fracture mechanisms induced in a brittle material by a hard cutting indenter.” Int. J. Solids Struct., 38(44–45), 7747–7768.
Cook, N. G. W., Hood, M., and Tsai, F. (1984). “Observations of crack growth in hard rock loaded by an indenter.” Int. J. Rock Mech. Min. Sci., 21(2), 97–107.
Cundall, P. A., and Hart, R. D. (1992). “Numerical modelling of discontinua.” Eng. Comput., 9(2), 101–113.
Donze, F. V., Richefeu, V., and Magnier, S. A. (2009). “Advances in discrete element method applied to soil rock and concrete mechanics.” Electron. J. Geotech. Eng., 8, 1–44.
Franzius, J., and Potts, D. (2005). “Influence of mesh geometry on three-dimensional finite-element analysis of tunnel excavation.” Int. J. Geomech., 256–266.
Gertsch, R., Gertsch, L., and Rostami, J. (2007). “Disc cutting tests in Colorado Red Granite: Implications for TBM performance prediction.” Int. J. Rock Mech. Min. Sci., 44(2), 238–246.
Gong, Q. M., Zhao, J., and Jiao, Y. Y. (2005). “Numerical modeling of the effects of joint orientation on rock fragmentation by TBM cutters.” Tunnelling Underground Space Technol., 20(2), 183–191.
Graziani, A., Rossini, C., and Rotonda, T. (2012). “Characterization and DEM modeling of shear zones at a large dam foundation.” Int. J. Geomech., 648–664.
Hockey, B. J., and Lawn, B. R. (1975). “Electron microscopy of microcracking about indentations in aluminium oxide and silicon carbide.” J. Mater. Sci., 10(8), 1275–1284.
Hoek, E. (1983). “Strength of jointed rock masses.” Géotechnique, 33(3), 187–223.
Hoek, E. (1990). “Estimating Mohr-Coulomb friction and cohesion values from the Hoek-Brown failure criterion.” Int. J. Rock Mech. Min. Sci., 27(3), 227–229.
Hoek, E., and Brown, E. T. (1980). “Empirical strength criterion for rock masses.” J. Geotech. Engrg. Div., 106(9), 1013–1035.
Hoek, E., and Brown, E. T. (1997). “Practical estimates of rock mass strength.” Int. J. Rock Mech. Min. Sci., 34(8), 1165–1186.
Hu, B., Zhang, N., Wang, S. J., and Chen, J. S. (2011). “Model test and strength analysis research on intermittent joint rock mass.” Chin. J. Underground Space and Eng., 7(4), 657–665.
Li, L., Lee, P., Tsui, Y., Tham, L., and Tang, C. (2003). “Failure process of granite.” Int. J. Geomech., 84–98.
Liang, Z. Z., Xing, H., Wang, S. Y., Williams, D. J., and Tang, C. A. (2012). “A three-dimensional numerical investigation of the fracture of rock specimens containing a pre-existing surface flaw.” Comput. Geotech., 45, 19–33.
Lin, P., Wong, R. H. C., and Chau, K. T. (2000). “Multi-crack coalescence in rock-like material under uniaxial and biaxial loading.” Key Eng. Mater., 183, 809–814.
Lindqvist, P. A., Suarez, L. M., Montoto, M., Tan, X. C., and Kou, S. Q. (1994). “Rock indentation database–Testing procedures, results, and main conclusions.” SKB Rep.: Pr 44-94-023, SKB, Stockholm, Sweden.
Liu, H. Y., Kou, S. Q., Lindqvist, P. A., and Tang, C. A. (2002). “Numerical simulation of the rock fragmentation process induced by indenters.” Int. J. Rock Mech. Min. Sci., 39(4), 491–505.
Liu, X., Liu, Q., Wei, L., and Huang, X. (2016). “Improved strength criterion and numerical manifold method for fracture initiation and propagation.” Int. J. Geomech, E4016007.
Munjiza, A., Owen, D., and Bicanic, N. (1995). “A combined finite-discrete element method in transient dynamics of fracturing solids.” Eng. Comput., 12(2), 145–174.
O’Sullivan, C. (2011). “Particle-based discrete element modeling: geomechanics perspective.” Int. J. Geomech., 449–464.
Pang, S. S., and Goldsmith, W. (1990). “Investigation of crack formation during loading of brittle rock.” Rock Mech. Rock Eng., 23(1), 53–63.
Sagong, M., and Bobet, A. (2002). “Coalescence of multiple flaws in a rock-model material in uniaxial compression.” Rock Mech. Min. Sci., 39(2), 229–241.
Shi, G. H. (1991). “Manifold method of material analysis.” Transactions of the 9th Army Conf. on Applied Mathematics and Computing, U.S. Army Research Office, Minneapolis, 57–76.
Shi, G. H., and Goodman, R. E. (1989). “Generalization of two-dimensional discontinuous deformation analysis for forward modelling.” Int. J. Numer. Anal. Methods Geomech., 13(4), 359–380.
Teale, R. (1965). “The concept of specific energy in rock drilling.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 2(1), 57–73.
Tsay, R., Chiou, Y., and Chuang, W. (1999). “Crack growth prediction by manifold method.” J. Eng. Mech., 884–890.
Vitae, A. L., Figi, D., and Grasselli, G. (2014). “Fracture development around deep underground excavations: Insights from FDEM modelling.” J. Rock Mech. Geotech. Eng., 6(6), 493–505.
Wagner, H., and Schümann, E. R. H. (1971). “The stamp-load bearing strength of rock an experimental and theoretical investigation.” Rock Mech., 3(4), 185–207.
Wallace, J. C., Ho, C. E., Bergh, C. J., Zhao, J., Zhou, Y. X., and Choa, V. (1995). “A proposed warehouse-shelter cavern scheme in Singapore granite.” Tunnelling Underground Space Technol., 10(2), 163–167.
Wu, Z. J., and Wong, L. N. Y. (2012). “Frictional crack initiation and propagation analysis using the numerical manifold method.” Comput. Geotech., 39, 38–53.
Yu, M. H., Zan, Y. W., Zhao, J., and Yoshimine, M. (2002). “A unified strength criterion for rock material.” Int. J. Rock Mech. Min., 39(8), 975–989.
Zhang, K. Z., Yu, H. D., Liu, Z. P., and Lai, X. M. (2010). “Dynamic characteristic analysis of TBM tunnelling in mixed-face conditions.” Simul. Modell. Pract. Theory, 18(7), 1019–1031.
Zhao, J. (1996). “Construction and utilization of rock caverns in Singapore Part A: The Bukit Timah granite bedrock resource.” Tunnelling Underground Space Technol., 11(1), 65–72.
Zhou, X., and Bi, J. (2016). “3D numerical study on the growth and coalescence of pre-existing flaws in rocklike materials subjected to uniaxial compression.” Int. J. Geomech., 04015096.
Zhou, X. P., Bi, J., and Qian, Q. H. (2015). “Numerical simulation of crack growth and coalescence in rock-like materials containing multiple pre-existing flaws.” Rock Mech. Rock Eng., 48(3), 1097–1114.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Mar 3, 2016
Accepted: Sep 8, 2016
Published online: Oct 18, 2016
Discussion open until: Mar 18, 2017
Published in print: Jun 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.