Modeling Pile Setup in Natural Clay Deposit Considering Soil Anisotropy, Structure, and Creep Effects: Case Study
Publication: International Journal of Geomechanics
Volume 17, Issue 3
Abstract
This paper reports the results of a numerical investigation of the behavior of a natural soft clay deposit under the installation of a case study pile. The case study problem included installation of an instrumented close-ended displacement pile in a soft marine clay deposit, known as Bothkennar clay, in Scotland. The site has been used for a number of years as a geotechnical test bed site, and the clay has been comprehensively characterized with both in situ tests and laboratory experiments. The soft soil behavior, both after pile installation and subsequent consolidation, was reproduced by using an advanced critical-state-based constitutive model that accounts for the anisotropy of soil fabric and destructuration effects during plastic straining. Furthermore, a time-dependent extension of the model was used to study soil creep and the significance of its consideration in the overall pile-installation effects. The simulation results were compared against field measurements; furthermore, for comparison, the pile installation was also analyzed using the well-known isotropic modified Cam-clay model to highlight the importance of considering inherent features of natural soil, such as anisotropy and structure, in the simulations. A series of sensitivity analyses was also performed to evaluate the influence of initial anisotropy and bonding values on simulation results and to check the reliability of the numerical analyses.
Get full access to this article
View all available purchase options and get full access to this article.
References
Albert, C., Zdravkovic, L., and Jardine, R. (2003). “Behaviour of Bothkennar clay under rotation of principal stresses.” Proc., Int. Workshop on Geotechnics of Soft Soils—Theory and Practice, SCMEP, Noordwijkerhout, Netherlands, 441–447.
Augustesen, A., Andersen, L., and Sørensen, C. S. (2006). “Assessment of time functions for piles driven in clay.” DCE Technical Memorandum, Dept. of Civil Engineering, Aalborg Univ., Aalborg, Denmark.
Azzouz, A., and Morrison, M. (1988). “Field measurements on model pile in two clay deposits.” J. Geotech. Eng., 104–121.
Bond, A. J., Dalton, J., and Jardine, R. J. (1991). “Design and performance of the Imperial College instrumented pile.” Geotech. Test J., 14(4), 413–424.
Bond, A. J., and Jardine, R. J. (1991). “Effects of installing displacement piles in a high OCR clay.” Géotechnique, 41(3), 341–363.
Brinkgreve, R. B. J., Swolfs, W. M., and Engin, E. (2013). PLAXIS 2D anniversary edition reference manual, Delft Univ. of Technology, Delft, Netherlands.
Burns, S., and Mayne, P. (1999). “Pore pressure dissipation behavior surrounding driven piles and cone penetrometers.” Transportation Research Record, 1675, 17–23.
Carter, J. P., Randolph, M. F., and Wroth, C. P. (1979). “Stress and pore pressure changes in clay during and after the expansion of a cylindrical cavity.” Int. J. Numer. Anal. Methods Geomech., 3(4), 305–322.
Castro, J., and Karstunen, M. (2010). “Numerical simulations of stone column installation.” Can. Geotech. J., 47(10), 1127–1138.
Castro, J., Karstunen, M., Sivasithamparam, N., and Sagaseta, C. (2013). “Numerical analyses of stone column installation in Bothkennar clay.” Proc., Int. Conf. on Installation Effects in Geotechnical Engineering, CRC Press, Boca Raton, FL, 212–218.
Chow, F., and Jardine, R. J. (1996). “Investigations into the behaviour of displacement piles for offshore foundations.” Int. J. Rock Mech. Min. Sci., 33(7), 319A–320A.
Clausen, C. J. F., and Aas, P. M. (2000). “Bearing capacity of driven piles in clays.” NGI Report, Norwegian Geotechnical Institute, Oslo, Norway.
Collins, I. F., and Stimpson, J. R. (1994). “Similarity solutions for drained and undrained cavity expansions in soils.” Géotechnique, 44(1), 21–34.
Dafalias, Y. F. (1987). “An anisotropic critical state clay plasticity model.” Proc., 2nd Int. Conf. on Constitutive Laws for Engineering Materials, Elsevier Science, Amsterdam, Netherlands, 513–521.
Dafalias, Y. F., Manzari, M. T., and Papadimitriou, A. G. (2006). “SANICLAY: Simple anisotropic clay plasticity model.” Int. J. Numer. Anal. Methods Geomech., 30(12), 1231–1257.
Davies, M., and Newson, T. (1993). “A critical state constitutive model for anisotropic soil.” Predictive Soil Mechanics, Proc. of the Wroth Memorial Symp., Thomas Telford, London, 219–229.
Doherty, P., and Gavin, K. (2011a). “The shaft capacity of displacement piles in clay: A state of the art review.” Geotech. Geol. Eng., 29(4), 389–410.
Doherty, P., and Gavin, K. (2011b). “Shaft capacity of open-ended piles in clay.” J. Geotech. Geoenviron. Eng., 1090–1102.
Fellenius, B., Riker, R., O'Brien, A., and Tracy, G. (1989). “Dynamic and static testing in soil exhibiting set‐up.” J. Geotech. Eng., 984–1001.
Gallagher, D., Gavin, K., McCabe, B., and Lehane, B. (2004). “Experimental investigation of the response of a driven pile in soft silt.” Proc., 18th Australasian Conf. on the Mechanics of Structures and Materials, Vol. II, CRC Press, Boca Raton, FL, 991–996.
Gens, A., and Nova, R. (1993). “Conceptual bases for a constitutive model for bonded soils and weak rocks.” Geotechnical engineering of hard soils-soft rocks, Vol. 1, A. A. Balkema, Rotterdam, Netherlands, 485–494.
Graham, J., Noonan, M. L., and Lew, K. V. (1983). “Yield states and stress–strain relationships in a natural plastic clay.” Can. Geotech. J., 20(3), 502–516.
Grimstad, G., Degago, S., Nordal, S., and Karstunen, M. (2010). “Modeling creep and rate effects in structured anisotropic soft clays.” Acta Geotech., 5(1), 69–81.
Gwizdała, K., and Więcławski, P. (2013). “Influence of time on the bearing capacity of precast piles.” Studia Geotech. Mech., 35(4), 65–74.
Heydinger, A. G., and O'Neill, M. W. (1986). “Analysis of axial pile-soil interaction in clay.” Int. J. Numer. Anal. Methods Geomech., 10(4), 367–381.
Hinchberger, S. D., and Rowe, R. K. (2005). “Evaluation of the predictive ability of two elastic-viscoplastic constitutive models.” Can. Geotech. J., 42(6), 1675–1694.
Holtz, W. G., and Lowitz, C. A. (1965). “Effects of driving displacement piles in lean clay.” J. Soil Mech. Found. Div., 91(5), 1–14.
Houlsby, G. T., Kelly, R. B., Huxtable, J., and Byrne, B. W. (2005). “Field trials of suction caissons in clay for offshore wind turbine foundations.” Géotechnique, 55(4), 287–296.
Institution of Civil Engineers. (1992). Géotechnique, 42(2) [special issue].
Karstunen, M., Krenn, H., Wheeler, S., Koskinen, M., and Zentar, R. (2005). “Effect of anisotropy and destructuration on the behavior of Murro test embankment.” Int. J. Geomech., 87–97.
Karstunen, M., Wiltafsky, C., Krenn, H., Scharinger, F., and Schweiger, H. F. (2006). “Modelling the behaviour of an embankment on soft clay with different constitutive models.” Int. J. Numer. Anal. Methods Geomech., 30(10), 953–982.
Karstunen, M., and Yin, Z. Y. (2010). “Modelling time-dependent behaviour of Murro test embankment.” Géotechnique, 60(10), 735–749.
Kavvadas, M. (1982). “Non-linear consolidation around driven piles in clays.” Ph.D. thesis, Massachusetts Institute of Technology, Cambridge, MA.
Kim, D. (2004). “Comparisons of constitutive models for anisotropic soils.” KSCE J. Civ. Eng., 8(4), 403–409.
Kirsch, F. (2006). “Vibro stone column installation and its effect on ground improvement.” Proceedings of the International Conference on Numerical Modelling of Construction Processes in Geotechnical Engineering for Urban Environment, CRC Press, Boca Raton, FL, 115–124.
Konrad, J. M., and Roy, M. (1987). “Bearing capacity of friction piles in marine clay.” Géotechnique, 37(2), 163–175.
Lehane, B. M., and Jardine, R. J. (1994). “Displacement-pile behaviour in a soft marine clay.” Can. Geotech. J., 31(2), 181–191.
Leoni, M., Karstunen, M., and Vermeer, P. A. (2008). “Anisotropic creep model for soft soils.” Géotechnique, 58(3), 215–226.
Liyanapathirana, D. (2008). “A numerical model for predicting pile setup in clay.” Proc., GeoCongress 2008: Characterization, Monitoring, and Modeling of GeoSystems, ASCE, Reston, VA, 710–717.
McGinty, K. (2006). “The stress-strain behaviour of Bothkennar clay.” Ph.D. thesis, Univ. of Glasgow, Glasgow, Scotland.
Niarchos, D. G. (2012). “Analysis of consolidation around driven piles in overconsolidated clay.” M.Sc. thesis, Massachusetts Institute of Technology, Cambridge, MA.
Nishimura, S., Minh, N. A., and Jardine, R. J. (2007). “Shear strength anisotropy of natural London clay.” Géotechnique, 57(1), 49–62.
O’Neill, M. W., Hawkins, R. A., and Audibert, J. M. (1982). “Installation of pile group in overconsolidated clay.” J. Geotech. Engrg. Div., 108(11), 1369–1386.
Pestana, J., Hunt, C., and Bray, J. (2002). “Soil deformation and excess pore pressure field around a closed-ended pile.” J. Geotech. Geoenviron. Eng., 1–12.
PLAXIS 2D AE [Computer software]. Plaxis, Delft, Netherlands.
Randolph, M. F. (2003). “Science and empiricism in pile foundation design.” Géotechnique, 53(10), 847–875.
Randolph, M. F., Carter, J. P., and Wroth, C. P. (1979). “Driven piles in clay: The effects of installation and subsequent consolidation.” Géotechnique, 29(4), 361–393.
Roscoe, K. H., and Burland, J. (1968). “On the generalized stress-strain behaviour of wet clay.” Eng. Plast., 553–609.
Roy, M., Blanchet, R., Tavenas, F., and Rochelle, P. L. (1981). “Behaviour of a sensitive clay during pile driving.” Can. Geotech. J., 18(1), 67–85.
Sekiguchi, H., and Ohta, H. (1977). “Induced anisotropy and time dependency in clay.” Proc., 9th ICSMFE, Constitutive Equations of Soils, Vol. 17, ISSMFE, Tokyo, 229–238.
Serridge, C. J., and Sarsby, R. W. (2008). “A review of field trials investigating the performance of partial depth vibro stone columns in a deep soft clay deposit.” Geotechnics of soft soils: Focus on ground improvement, Taylor & Francis, London, 293–298.
Sheil, B. B., McCabe, B. A., Hunt, C. E., and Pestana, J. M. (2015). “A practical approach for the consideration of single pile and pile group installation effects in clay: Numerical modelling.” J. Geo-Eng. Sci., 2(3, 4), 119–142.
Sills, G. C. (1975). “Some conditions under which Biot's equations of consolidation reduce to Terzaghi's equation.” Géotechnique, 25(1), 129–132.
Sivasithamparam, N. (2012). “Development and implementation of advanced soft soil models in finite elements.” Ph.D. thesis, Univ. of Strathclyde, Glasgow, U.K.
Sivasithamparam, N., Karstunen, M., and Bonnier, P. (2015). “Modelling creep behaviour of anisotropic soft soils.” Comput. Geotech., 69, 46–57.
Soderberg, L. O. (1962). “Consolidation theory applied to foundation pile time effects.” Géotechnique, 12(3), 217–225.
Svinkin, M. R., Morgano, C. M., and Morvant, M. (1994). “Pile capacity as a function of time in clayey and sandy soils.” Proc., 5th Int. Conf. and Exhibition on Piling and Deep Foundations, Westrade Fairs, Bruges, Belgium, 1.11.1–1.11.8.
Vermeer, P. A., Stolle, D. F. E., and Bonnier, P. G. (1998). “From the classical theory of secondary compression to modern creep analysis.” Proc., Computer Methods and Advances in Geomechanics, A. A. Balkema, Rotterdam, Netherlands, 2469–2478.
Wheeler, S., Karstunen, M., and Naatanen, A. (1999). “Anisotropic hardening model for normally consolidated soft, clays.” Proc., 7th Int. Symp. on Numerical Models in Geomechanics, A. A. Balkema, Rotterdam, Netherlands, Vol. II, 33–40.
Wheeler, S. J., Näätänen, A., Karstunen, M., and Lojander, M. (2003). “An anisotropic elastoplastic model for soft clays.” Can. Geotech. J., 40(2), 403–418.
Whittle, A., and Kavvadas, M. (1994). “Formulation of MIT‐E3 constitutive model for overconsolidated clays.” J. Geotech. Eng., 173–198.
Xu, X. T., Liu, H. L., and Lehane, B. M. (2006). “Pipe pile installation effects in soft clay.” Proc. Inst. Civ. Eng. Geotech. Eng., 159(4), 285–296.
Yildiz, A. (2009). “Numerical modeling of vertical drains with advanced constitutive models.” Comput. Geotech., 36(6), 1072–1083.
Yu, H. S. (1990). “Cavity expansion theory and its application to the analysis of pressuremeters.” Ph.D. thesis, Univ. of Oxford, Oxford, U.K.
Yu, H. S. (2000). Cavity expansion methods in geomechanics, Springer, New York.
Zhou, C., Yin, J., Zhu, J., and Cheng, C. (2005). “Elastic anisotropic viscoplastic modeling of the strain-rate-dependent stress–strain behavior of k0-consolidated natural marine clays in triaxial shear tests.” Int. J. Geomech., 218–232.
Zwanenburg, C. (2013). “Application of SCLAY1 model to peat mechanics.” Internal Rep., Deltares, Delft, Netherlands.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 17 • Issue 3 • March 2017
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jan 11, 2016
Accepted: Jun 27, 2016
Published online: Aug 17, 2016
Discussion open until: Jan 17, 2017
Published in print: Mar 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.