Evidence for a Highly Conductive Fracture after Water Fracturing in the GeneSys Project
Publication: International Journal of Geomechanics
Volume 16, Issue 3
Abstract
The GeneSys project aims to develop a low-permeability, sedimentary reservoir of the Northern German Basin for the provision of geothermal energy to heat the Federal Institute for Geosciences and Natural Resources (BGR) located at the Geo Center in Hanover, Germany. In May 2011, a massive fracturing (frac) operation was performed to create a large heat exchanger at a depth of 3,700 m. Subsequent to the frac operation, two low-rate injection tests were conducted below fracture-closure pressure. The injection phases of the two tests provide evidence for a large and highly conductive fracture, although proppants were not used during the frac operation, indicating that the fracture stays open because of self-propping effects, at least in the explored range of effective stress. Hydraulically active fracture areas of more than 0.5 km2 were calculated from an analysis of the pressure transient during the low-rate injection tests relying on matrix permeabilities determined in laboratory experiments. In principle, such areas are sufficient to yield geothermal power in the range of 2 MW (thermal performance). The hydraulically active fracture area and estimated fracture transmissibility diminished between the two low-rate injection tests and, hence, with increasing effective normal stress. The authors suppose this observation is because of a hydromechanical component of self-propping effects. Similarly, the mismatch between the shut-in observations and conventional hydraulic models indicates that hydromechanical processes affect the pressure transient by continuously decreasing the fracture aperture.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The GeneSys project is funded by the German Federal Ministry of Economics and Energy. Several investigations were funded by the German Federal Ministry for the Environment, Nature Conservation, Building, and Nuclear Safety.
References
Alagoa, A., and Ayoub, J. (1985). “How to simplify the analysis of fractured well tests.” World Oil, 201(5).
Baldschuhn, R., and Kockel, F. (1998). “Der Untergrund von Hannover und seiner Umgebung.” Ber. Nat. Ges., 140, 5–98 (in German).
Bandis, S. C., Lumsden, A. C., and Barton, N. R. (1983). “Fundamentals of rock joint deformation.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 20(6), 249–268.
Baria, R., Baumgärtner, J., Gérard, A., Jung, R., and Garnish, J. (1999). “European HDR research programme at Soultz-sous-Forêts (France) 1987–1996.” Geothermics, 28(4–5), 655–669.
Barree, R., and Mukherjee, H. (1996). “Determination of pressure dependent leakoff and its effect on fracture geometry.” SPE Annual Technical Conf. and Exhibition, SPE, Richardson, TX, 424.
Bourdet, D., Ayoub, J. A., and Pirard, Y. M. (1989). “Use of pressure derivative in well test interpretation.” SPE Form. Eval., 4(2), 293–302.
Cappa, F., Guglielmi, Y., Fénart, P., Merrien-Soukatchoff, V., and Thoraval, A. (2005). “Hydromechanical interactions in a fractured carbonate reservoir inferred from hydraulic and mechanical measurements.” Int. J. Rock Mech. Min. Sci., 42(2), 287–306.
Castillo, J. (1987). “Modified fracture pressure decline analysis including pressure-dependent leakoff.” Low Permeability Reservoirs Symp., SPE, Richardson, TX, 273–281.
Cholet, H. (2000). “Pressure losses.” Well production practical handbook, H. Cholet, ed., Editions Technip, Paris, 97–103.
Cinco-Ley, H., and Samaniego-V., F. (1981). “Transient pressure analysis for fractured wells.” J. Petrol. Technol., 33(9), 1749–1766.
Cinco-Ley, H., Samaniego-V, F., and Dominguez, A. N. (1978). “Transient pressure behavior for a well with a finite-conductivity vertical fracture.” SPE J., 18(4), 253–264.
Clark, K. K. (1968). “Transient pressure testing of fractured water injection wells.” J. Petrol. Technol., 20(6), 639–643.
Cooke, C. E. (1977). “Fracturing with a high-strength proppant.” J. Petrol. Technol., 29(10), 1222–1226.
Cuenot, N., Dorbath, C., and Dorbath, L. (2008). “Analysis of the microseismicity induced by fluid injections at the EGS site of Soultz-sous-Forêts (Alsace, France): Implications for the characterization of the geothermal reservoir properties.” Pure Appl. Geophys., 165(5), 797–828.
Cutler, R. A., Enniss, D. O., Jones, A. H., and Swanson, S. R. (1985). “Fracture conductivity comparison of ceramic proppants.” SPE J., 25(2), 157–170.
Dodson, C. R., and Standing, M. B. (1944). “Pressure-volume-temperature and solubility relations for natural-gas-water mixtures.” Drilling and production practice, American Petroleum Institute, Washington, DC, 8.
Dros, A. N. P., Kuznetsov, A. M., and Hagoort, J. (1998). “Interpretation of falloff tests on fractured wells of the Barsukov oil field in western Siberia.” European Petroleum Conf., SPE, Richardson, TX, 363–369.
Economides, M. J., and Nolte, K. G. (2000). Reservoir stimulation, Wiley & Sons, Chichester, U.K.
Goodman, R. (1974). “The mechanical properties of joints.” Proc., Third Int. ISRM Congress, National Academy of Sciences, Washington, DC, 127–140.
Gringarten, A. C., Ramey, H. J. Jr., and Raghavan, R. (1974). “Unsteady-state pressure distributions created by a well with a single infinite-conductivity vertical fracture.” SPE J., 14(4), 347–360.
Gringarten, A. C. (2008). “From straight lines to deconvolution: The evolution of the state of the art in well test analysis.” SPE Res. Eval. Eng., 11(1), 41–62.
Gulrajani, S. N., and Nolte, K. G. (2000). “Fracture evaluation using pressure diagnostics.” Reservoir stimulation, M. J. Economides and K. G. Nolte, eds., Wiley & Sons, Chichester, U.K, 1–63.
Hall, H. N. (1953). “Compressibility of reservoir rocks.” J. Petrol. Technol., 5(1), 17–19.
Harvey, A. H. (1998). Thermodynamic properties of water: Tabulation from the IAPWS Formulation 1995 for the thermodynamic properties of ordinary water substance for general and scientific use, U.S. Department of Commerce, Technology Administration, National Institute of Standards and Technology, Boulder, CO.
Hobday, C., and Worthington, M. H. (2012). “Field measurements of normal and shear fracture compliance.” Geophys. Prospect., 60(3), 488–499.
Horner, D. R. (1951). “Pressure build-up in wells.” Proc., Third World Petroleum Congress, Brill, Leiden, Netherlands, 503–521.
Jung, R. (1989). “Hydraulic in situ investigations of an artificial fracture in the Falkenberg granite.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 26(3–4), 301–308.
Jung, R., Orzol, J., Jatho, R., Kehrer, P., and Tischner, T. (2005). “The GENESYS Project: Extraction of geothermal heat from tight sediments.” Proc., Workshop on Geothermal Reservoir Engineering, Stanford Univ., Stanford, CA.
Kehrer, P., Orzol, J., Jung, R., Jatho, R., and Junker, R. (2007). “The GeneSys project—A contribution of GEOZENTRUM Hannover to the development of Enhanced Geothermal Systems (EGS).” Z. Dtsch. Ges. Geowiss., 158(1), 119–132.
Lee, D. S., Elsworth, D., Yasuhara, H., Weaver, J. D., and Rickman, R. (2010). “Experiment and modeling to evaluate the effects of proppant-pack diagenesis on fracture treatments.” J. Petrol. Sci. Eng., 74(1–2), 67–76.
Manga, M., et al. (2012). “Changes in permeability caused by transient stresses: Field observations, experiments, and mechanisms.” Rev. Geophys., 50(2),.
Matthews, C. S., and Russell, D. G. (1967). Pressure buildup and flow tests in wells, SPE, Dallas, TX.
Murdoch, L. C., and Germanovich, L. N. (2006). “Analysis of a deformable fracture in permeable material.” Int. J. Numer. Anal. Methods Geomech., 30(6), 529–561.
Nolte, K. (1979). “Determination of fracture parameters from fracturing pressure decline.” SPE Annual Technical Conf. and Exhibition, SPE, Richardson, TX.
Ortiz R., A. E., Jung, R., and Renner, J., (2013). “Two-dimensional numerical investigations on the termination of bilinear flow in fractures.” Solid Earth, 4(10), 331–345.
Orzol, J., Jung, R., Jatho, R., Tischner, T., and Kehrer, P. (2005). “The GeneSys-Project: Extraction of geothermal heat from tight sediments.” Proc., World Geothermal Congress, IGA, Bochum, Germany, 24–29.
Pechan, E., Tischner, T., and Renner, J. (2014). “Fracture properties after hydraulic stimulation in low-permeability sediments (GeneSys-project).” Proc., ISRM European Rock Mechanics Symp., CRC Press/Balkema, Leiden, Netherlands.
Polak, A., Elsworth, D., Yasuhara, H., Grader, A. S., and Halleck, P. M. (2003). “Permeability reduction of a natural fracture under net dissolution by hydrothermal fluids.” Geophys. Res. Lett., 30(20),.
Pyrak-Nolte, L. J., and Morris, J. P. (2000). “Single fractures under normal stress: The relation between fracture specific stiffness and fluid flow.” Int. J. Rock Mech. Min. Sci., 37(1–2), 245–262.
Rahman, M. M., Hossain, M. M., Crosby, D. G., Rahman, M. K., and Rahman, S. S. (2002). “Analytical, numerical and experimental investigations of transverse fracture propagation from horizontal wells.” J. Petrol. Sci. Eng., 35(3–4), 127–150.
Raven, K. G., and Gale, J. E. (1985). “Water flow in a natural rock fracture as a function of stress and sample size.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 22(4), 251–261.
Rutqvist, J., Tsang, C.-F., and Stephansson, O. (2000). “Uncertainty in the maximum principal stress estimated from hydraulic fracturing measurements due to the presence of the induced fracture.” Int. J. Rock Mech. Min. Sci., 37(1–2), 107–120.
Schäfer, F., et al. (2012). “Summarized report of the geothermal well Groß Buchholz Gt1.” Erdol Erdgas Kohle, 128(1), 20–26.
Smith, M. B., and Shlyapobersky, J. W. (2000). “Basics of hydraulic fracturing.” Reservoir stimulation, M. J. Economides and K. G. Nolte, eds., Wiley & Sons, Chichester, U.K., 1–28.
Stegemeier, G. L., and Matthews, C. S. (1958). “A study of anomalous pressure build-up behavior.” Trans. AIME, 213, 44–50.
Stoddard, T., McLennan, J., and Moore, J. (2011). “Fracture conductivity of a bauxite-propped geothermal system at in-situ conditions.” Proc., Thirty-Sixth Workshop on Geothermal Reservoir Engineering, Stanford Univ., Stanford, CA, 1–8.
Tenzer, H., Schanz, U., Stang, H., Baisch, S., and Weidler, R. (2004). “Potential for geothermal power production from deep hot crystalline rock at Bad Urach (Southern Germany).” Z. Angew. Geol., 50(2), 43–49.
Tischner, T., et al. (2013). “Massive hydraulic fracturing in low permeable sedimentary rock in the GeneSys project.” Proc., Thirty-Eighth Workshop on Geothermal Reservoir Engineering, Stanford Univ., Stanford, CA.
Van Everdingen, A. F. (1953). “The skin effect and its influence on the productive capacity of a well.” J. Petrol. Technol., 5(6), 171–176.
Weijers, L., Kama, Y., Shemeta, J., and Cumella, S. (2009). “AV bigger is better—Hydraulic fracturing in the Williams Fork Formation in the Piceance Basin.” Proc., AAPG Annual Convention, AAPG Datapages, 〈www.searchanddiscovery.com〉 (Feb. 18, 2014).
Zhang, S., Yin, S., and Yuan, Y. (2015). “Estimation of fracture stiffness, in situ stresses, and elastic parameters of naturally fractured geothermal reservoirs.” Int. J. Geomech., 04014033.
Zimmermann, G., and Reinicke, A. (2010). “Hydraulic stimulation of a deep sandstone reservoir to develop an enhanced geothermal system: Laboratory and field experiments.” Geothermics, 39(1), 70–77.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 16 • Issue 3 • June 2016
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Mar 18, 2014
Accepted: Apr 15, 2015
Published online: Dec 16, 2015
Discussion open until: May 16, 2016
Published in print: Jun 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.