Deformation-Based Limit State Analysis of Embankment Dams Including Geometry and Water Level Effects
Publication: International Journal of Geomechanics
Volume 15, Issue 5
Abstract
The research presented in this paper is focused on the effect of various parameters on the deformation response of embankment dams and the corresponding performance limit states. The parameters considered include the geometry of the embankment and hydraulic loading in terms of intensity, duration, and cycles of loading and unloading as a result of the rise and fall of the water level in the reservoir. The analysis of a model embankment dam is conducted using the finite-element approach and the results are incorporated into simplified deformation-based probabilistic analyses. The effect of the change in geometry on shear strains and horizontal deformations and the corresponding probabilities of exceeding three predefined limit states are presented. The analyses are also used to demonstrate the importance of taking into account the storm loading history when assessing the stability of the flood protection earth structures under future flood events. In a larger embankment model, the shear zone propagates deeper for failure to occur. The time to exceed Limit States I, II, and III increases as the size of an embankment model becomes longer. For example, failure occurs after 4.6 days in a model with a size factor of 0.1 compared with 12 days for a model with a size factor of 0.2. This is mainly because the advancement of the saturation front to a critical level occurs in less time in the smaller embankment.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based upon work supported by the Coastal Hazards Center of Excellence, a U.S. Department of Homeland Security Science and Technology Center of Excellence, under Award No. 2008-ST-061-ND 0001. The views and conclusions contained in this document are those of the authors and should not be interpreted as necessarily representing the official policies, either expressed or implied, of the U.S. Department of Homeland Security.
References
AASHTO. (2012). AASHTO LRFD bridge design specifications, 6th Ed., AASHTO, Washington, DC.
Ahmed-Zeki, A., Logan, N., McQuarrie, W., and Jaduram, R. (2000). “Monitoring the cut-off wall performance of Upper Huia Dam.” Performance confirmation of constructed geotechnical facilities, ASCE, New York, 212–227.
ASCE. (2011). “Policy statement 470—Dam repair and rehabilitation.” 〈http://www.asce.org/Public-Policies-and-Priorities/Public-Policy-Statements/Policy-Statement-470---Dam-Repair-and-Rehabilitation/〉 (Jul. 1, 2013).
Bauer, J., and Pula, W. (2000). “Reliability with respect to settlement limit-states of shallow foundations on linearly-deformable subsoil.” Comput. Geotech., 26(3–4), 281–308.
Berilgen, M. M. (2007). “Investigation of stability of slopes under drawdown conditions.” Comput. Geotech., 34(2), 81–91.
Bouassida, M., Jellali, B., and Porbaha, A. (2009). “Limit analysis of rigid foundations on floating columns.” Int. J. Geomech., 89–101.
Bureau of Reclamation. (2003). “Guidelines for achieving public protection in dam safety decision making.” U.S. Dept. of the Interior, Denver.
Callari, C., and Abati, A. (2009). “Finite element methods for unsaturated porous solids and their application to dam engineering problems.” Comput. Struct., 87(7–8), 485–501.
Charles, J. A., and Bromhead, E. N. (2008). “Contributions to Géotechnique 1948–2008: Slope stability and embankment dams.” Géotechnique, 58(5), 385–389.
Dickenson, S. E. (2007). “Instrumentation and monitoring of port facilities: Planning, funding, field applications, and long-term benefits.” Proc., 11th Triennial Int. Conf., ASCE, Reston, VA, 1–10.
Duncan, J. M. (2000). “Factors of safety and reliability in geotechnical engineering.” J. Geotech. Geoenviron. Eng., 307–316.
Duncan, J. M., and Chang, C.-Y. (1970). “Nonlinear analysis of stress and strain in soil.” J. Soil Mech. and Found. Div., 96(5), 1629–1653.
Fu, J., and Jin, S. (2009). “A study on unsteady seepage flow through dam.” J. Hydrodyn. Ser. B, 21(4), 499–504.
Gourvenec, S., and Jensen, K. (2009). “Effect of embedment and spacing of cojoined skirted foundation systems on undrained limit states under general loading.” Int. J. Geomech., 267–279.
Han, C. Y., Wang, J.-H., Xia, X.-H., and Chen, J. J. (2012). “Limit analysis for local and overall stability of slurry trench in cohesive soil.” Int. J. Geomech., (Nov. 3, 2012).
Hart, D. J., Bradbury, K. R., and Feinstein, D. T. (2006). “The vertical hydraulic conductivity of an aquitard at two spatial scales.” Ground Water, 44(2), 201–211.
Huang, M. S., and Jia, C.-Q. (2009). “Strength reduction FEM in stability analysis of soil slopes subjected to transient unsaturated seepage.” Comput. Geotech., 36(1–2), 93–101.
Khalilzad, M., and Gabr, M. A. (2011a). “Deformation-based limit states for earth embankments.” Geo-Frontiers 2011: Advances in Geotechnical Engineering, ASCE, Reston, VA, 3639–3648.
Khalilzad, M., and Gabr, M. A. (2011b). “Limit states approach for coupled seepage deformation analysis of earth embankments.” Proc., Dam Safety, Association of State Dam Safety Officials (ASDSO), Lexington, KY.
Khalilzad, M., Gabr, M. A., and Hynes, M. E. (2014). “Effects of woody vegetation on seepage-induced deformation and related limit state analysis of levees.” Int. J. Geomech., 302–312.
Kohgo, Y., Takahashi, A., Asano, L., and Suzuki, T. (2006). “FEM consolidation analysis of centrifuge test for rockfill dam model during first reservoir filling.” Unsaturated Soils, ASCE, Reston, VA, 2312–2323.
Kondner, R. L., and Zelasko, J. S. (1963). “A hyperbolic stress-strain formulation of sands.” Proc., 2nd Pan-American Conf. on Soil Mechanics and Foundation Engineering (ICOSFE), Vol. 1, Sao Paulo, Brazil, 289–324.
Lu, N., and Godt, J. (2008). “Infinite slope stability under steady unsaturated seepage conditions.” Water Resour. Res., 44(11), 1–13.
Meyerhof, G. G. (1982). “Limit states design in geotechnical engineering.” Struct. Saf., 1(1), 67–71.
Morrice, J. A., Valett, H. M., Dahm, C. N., and Campana, M. E. (1997). “Alluvial characteristics, groundwater–surface water exchange and hydrological retention in headwater streams.” Hydrol. Processes, 11(3), 253–267.
National Oceanic and Atmospheric Administration (NOAA). (2011). “National Weather Service.” 〈http://water.weather.gov/ahps2/hydrograph.php?wfo=lsx&gage=UNNM7〉 (May 16, 2011).
Özer, A. T., and Bromwell, L. G. (2012). “Stability assessment of an earth dam on silt/clay tailings foundation: A case study.” Eng. Geol., 151, 89–99.
Phoon, K. K., and Kulhawy, P. H. (2008). “Serviceability limit state reliability-based design.” Reliability-based design in geotechnical engineering—Computations and applications, K. K. Phoon, ed., Taylor & Francis, London, 344–384.
PLAXIS 2D 2010 [Computer software]. Delft, Netherlands, Plaxis.
Schanz, T., and Vermeer, P. A. (1998). “On the stiffness of sands.” Pre-failure deformation behaviour of geomaterials, Institution of Civil Engineers (ICE), London, 383–387.
Schanz, T., Vermeer, P. A., and Bonnier, P. G. (1999). “The hardening soil model: Formulation and verification.” Beyond 2000 in computational geotechnics—10 Years of PLAXIS, Balkema, Rotterdam, Netherlands.
Seed, R. B., Mitchell, J. K., and Seed, H. B. (1990). “Kettleman Hills waste landfill slope failure. II: Stability analyses.” J. Geotech. Engrg., 669–690.
SLOPE/W 5 [Computer software]. Calgary, Alberta, Canada, Geo-Slope.
Stark, T. D., and Duncan, J. M. (1991). “Mechanisms of strength loss in stiff clays.” J. Geotech. Engrg., 139–154.
Task Committee of the Association of State Dam Safety Officials (TCASDSO). (2009). The cost of rehabilitating our nation’s dams: A methodology, estimate and proposed funding mechanisms, Association of State Dam Safety Officials (ASDSO), Lexington, KY.
Tavenas, F., and Leroueil, S. (1981). “Creep and failure of slopes in clays.” Can. Geotech. J., 18(1), 106–120.
U.S. Army COE (USACE). (1990). “Engineering and design, settlement analysis.” Engineering Manual No. 1110-1-1904, Dept. of the Army, Washington, DC.
U.S. Army COE (USACE). (2006). “Reliability analysis and risk assessment for seepage and slope stability failure modes for embankment dams.” Engineering Technical Letter No. 1110-2-561, Dept. of the Army, Washington, DC.
U.S. Army COE (USACE). (2011). “Safety of dams—Policy and procedures.” ER 1110-2-1156, Dept. of the Army, Washington, DC.
Viratjandr, C., and Michalowski, R. L. (2006). “Limit analysis of submerged slopes subjected to water drawdown.” Can. Geotech. J., 43(8), 802–814.
Wellington, C. D., and Vlachaki, C. (2004). “Serviceability limit state criteria for the seismic assessment of R/C building—Paper 2269.” Proc., 13th World Conf. on Earthquake Engineering, Vancouver, BC, Canada.
Whitman, R. V. (1984). “Evaluating calculated risk in geotechnical engineering.” J. Geotech. Engrg., 143–188.
Yu, H. S., Salgado, R., Sloan, S. W., and Kim, J. M. (1998). “Limit analysis versus limit equilibrium for slope stability.” J. Geotech. Geoenviron. Eng., 1–11.
Zhang, L. M., and Ng, A. M. Y. (2005). “Probabilistic limiting tolerable displacements for serviceability limit state design of foundations.” Géotechnique, 55(2), 151–161.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 15 • Issue 5 • October 2015
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jul 18, 2013
Accepted: Jun 13, 2014
Published online: Jul 15, 2014
Published in print: Oct 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.