Experimental and Numerical Study of Micropiles to Reinforce High Railway Embankments
Publication: International Journal of Geomechanics
Volume 13, Issue 6
Abstract
The construction of railway embankments on loose beds using reinforcing elements results in a modification of the embankments slope, which significantly reduces the amount of earthworks. In addition, reinforcement of both bed and embankment is essential to increase the load-bearing capacity and control the settlements. A solution for high railway-embankment stabilization and enhancing the operational axle load is the use of micropiles in the embankment toe to transmit the applied loads to the firm underlying layers and avoid the deep sliding of loose subgrade. This paper presents three experimental models of embankments of 10 m in height on a scale of to set up a number of loading tests: one based on a non-reinforced embankment and two others based on reinforced embankments that are stabilized with two different arrangements of micropiles. During laboratory tests, the data, including the load-bearing capacity of embankments, displacements of embankment crest and bed surface, and axial strain of micropiles were measured using the instrumentation tools. In the next step, three numerical models were developed by using the PLAXIS-3D code based on the FEM. Then, a comparison was made between the experimental and numerical data to verify the outputs of the numerical analyses. In the procedure of numerical analyses, elastoplastic behaviors of embankment material and bed were defined based on the Mohr-Coulomb failure criterion, and micropiles were considered as linear elastic elements. Finally, after accomplishing a series of sensitivity analyses on the geometric parameters of micropiles, their efficiency factor was classified in the process of arrangement optimization.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (1983). “Test method for relative density of cohesionless soils.” D2049, West Conshohocken, PA.
ASTM. (2003). “Standard test method for bearing capacity of soil for static load and spread footings.” D1194, West Conshohocken, PA.
ASTM. (2006). “Test method for direct shear test of soils under consolidated drained conditions.” D3080, West Conshohocken, PA.
ASTM. (2007a). “Standard test method for particle-size analysis of soils.” D422, West Conshohocken, PA.
ASTM. (2007b). “Test method for density and unit weight of soil in place by sand-cone method.” D1556, West Conshohocken, PA.
ASTM. (2009). “Test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens).” C109, West Conshohocken, PA.
ASTM. (2010a). “Standard test method for unconfined compressive strength of cohesive soil.” D2166, West Conshohocken, PA.
ASTM. (2010b). “Test methods for specific gravity of soil solids by water pycnometer.” D854, West Conshohocken, PA.
ASTM. (2011a). “Standard practice for steel bars, selection guide, composition, and mechanical properties.” A400, West Conshohocken, PA.
ASTM. (2011b). “Test methods for laboratory compaction characteristics of soil using standard effort (600 kN-m/m3).” D698, West Conshohocken, PA.
Brinkgreve, R. B. J., Broere, W., Burd, H. J., Soltys, G., Vermeer, P. A., and Waterman, D. (2002). PLAXIS-3D tunnel version 1.2 tutorial manual, PLAXIS, Delft, Netherlands.
Bruce, D. A. (2008). “The history of micropiles in North America.” Micropile Construction and Design Seminar, Association of Drilled Shaft Contractors, Irving, TX, 1–10.
Bruce, J., Ruel, M., Janes, M., and Ansari, N. (2004). “Design and construction of a micropile wall to stabilize a railway embankment.” Proc., 29th Annual Conf. on Deep Foundations, Deep Foundations Institute, Vancouver, BC, Canada, 1–11.
Cantoni, R., Collotta, T., Ghionna, V. N., and Moratti, P. V. (1989). “Design method for reticulated micropiles structures in sliding slopes.” Ground engineering, Vol. 22, Elsevier, New York, 41–47.
Federal Highway Admistration (FHWA). (2000). “Micropile design and construction guidelines.” Rep. FHWA-SA-97-070, DOT, Washington, DC, 31–200.
Haider, T. F., Byle, M. J., and Horvath, R. E. (2004). “Dam stabilization with micropiles.” Proc., Sessions of Geo-Denver 2000, ASCE, New York.
Harris, H. G., and Sabnis, G. M. (1999). Structural modelling and experimental techniques, 2nd Ed., CRC, Boca Raton, FL.
Hassen, G., Dias, D., and de Buhan, P. (2009). “Multiphase constitutive model for the design of piled-embankments: Comparison with three-dimensional numerical simulations.” Int. J. Geomech., 9(6), 258–266.
Howe, W. K. (2010). “Micropiles for slope stabilization.” Proc., 2010 Biennial Geotechnical Seminar, ASCE, New York.
Iai, S. (1989). “Similitude for shaking table tests on soil-structure-fluid model in 1g gravitational field.” Soils and Foundations, 29(1), 105–118.
Jenck, O., Dias, D., and Kastner, R. (2009). “Three-dimensional numerical modelling of a piled embankment.” Int. J. Geomech., 9(3), 102–112.
Khayyer, F. (2010). “Improvement the railway embankments with micropiles.” M.S. thesis, School of Railway Engineering of Iran Univ. of Science and Technology, Tehran, Iran.
Krawinkler, H. (1979). “Possibilities and limitations of scale-model testing in earthquake engineering.” Proc., 2nd US National Conf. on Earthquake Engineering, Stanford Univ., 283–292.
McManus, K. J., Charton, G., and Turner, J. P. (2004). “Effect of micropiles on seismic shear strain.” Proc., Geo Support Conf., ASCE, New York.
Misra, A., and Chen, C. H. (2007). “Load displacement relationships for micropiles.” Proc., Int. Deep Foundations Congress 2002, ASCE, New York.
PLAXIS-3D Tunnel 1.2 [Computer software]. Delft, Netherlands, Plaxis.
Richards, Th. D., and Rothbauer, M. J. (2004). “Lateral loads on pin piles (micropiles).” Proc., Geo Support Conf., ASCE, New York, 158–174.
Schofield, A. N., and Steedman, R. S. (1988). “State-of-the-art report: Recent developments on dynamic model testing in geotechnical engineering.” Proc., 9th World Conf. on Earthquake Engineering, Tokyo/Kyoto, 813–824.
Schwarz, H., Dietz, K., Koster, H., and Grob, Th. (2004). “Special use of micropiles and permanent anchors.” Proc., Geo Support Conf., ASCE, New York, 682–691.
Shahroudi, M. M., and Zakeri, J. A. (2006).“Investigating the effect of increasing axial load on the railway subgrade.” M.S. thesis, School of Railway Engineering of Iran Univ. of Science and Technology, Tehran, Iran.
Tokyo Sokki Kenkyujo. (2011). Strain gauge type (TML Pam E-101S) and civil engineering transducers (TML Pam E-720R) manuals, Tokyo Sokki Kenkyujo, Tokyo, 1–16.
International Union of Railways. (1994). Earthworks and track-bed layers for railway lines: UIC code, 2nd Ed., International Union of Railways, Paris, 85–100.
Wang, Z., Met, G., Cai, G., and Yu, X. (2009). “Dynamic finite element analysis of micropile foundation in subgrade.” Proc., Selected Papers from the 2009 Geo Hunan Int. Conf., ASCE, New York, 139–144.
Wolosick, J. R. (2009). “Ultimate micropile bond stresses observed during load testing in clays and sands.” Proc., Selected Papers of the 2009 Int. Foundation Congress and Equipment Expo., ASCE, New York.
Wood, D. M. (2004). Geotechnical modelling, version 2.2, CRC, Boca Raton, FL, 233–269.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 23, 2012
Accepted: Dec 14, 2012
Published online: Dec 17, 2012
Published in print: Dec 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.