Full-Scale Instrumented Testing and Three-Dimensional Modeling of Airfield Matting Systems
Publication: International Journal of Geomechanics
Volume 14, Issue 2
Abstract
Matting systems are used for temporary applications on soft soils to reduce ground pressure exerted by aircraft, heavy equipment, vehicles, and construction material. They have been used for military airfields, construction platforms, and similar applications. Previous evaluation studies of matting systems have typically consisted of full-scale testing, with only a limited amount of numerical modeling found in the literature. This paper presents results of full-scale accelerated testing of 21 test sections encompassing five matting systems, five soil-support conditions, and two aircraft loadings. One of the soil-support conditions was instrumented and tested in conjunction with three matting systems and one aircraft loading. Three-dimensional finite-element modeling was performed on the instrumented sections using the measured test data for calibration. Good matches of measured soil stresses were obtained with the model for two of the mats, whereas the model underpredicted stresses in the third mat. Modeling of the type performed in this paper was capable of correctly ranking the performance of the matting systems modeled relative to the full-scale test results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the U.S. Army COE for sponsoring this research and acknowledge the contribution of Dr. Philip Gullet (Mississippi State University) for providing technical assistance with the FE modeling. Permission to publish this work was given by the Director, Geotechnical and Structures Laboratory, U.S. Army Engineer Research and Development Center.
References
ABAQUS 6.10-2 [Computer software]. Providence, RI, Dassault Systèmes Simulia.
Anderton, G. L., and Gartrell, C. A. (2005). “Rapid maximum-on-ground (MOG) enhancement technologies. 1: Matting systems for contingency helipads and C-130 test sections.” Rep. ERDC/GSL TR-05-2, U.S. Army COE (USACE), Engineer Research and Development Center, Vicksburg, MS.
ASTM. (2002). “Standard test methods for laboratory compaction characteristics of soil using modified effort [ ()].” D1557-02, West Conshohocken, PA.
Berney, E. S., IV, Hodo, W. D., and Vera, J. A. (2006). “Determination of unit section modulus for finite element modeling of airfield matting systems.” Rep. ERDC/GSL TR-06-10, U.S. Army COE (USACE), Engineer Research and Development Center, Vicksburg, MS.
Brill, D. R., and Parsons, I. D. (2001). “Three-dimensional finite element analysis in airport pavement design.” Int. J. Geomech., 273–290.
Davids, W. G. (2001). “3D finite element study of load transfer at doweled joints in flat and curled rigid pavements.” Int. J. Geomech., 309–323.
Gartrell, C. A. (2007a). “Full-scale instrumented testing and analysis of matting systems for airfield parking ramps and taxiways.” M.S. thesis, Mississippi State Univ., Mississippi State, MS.
Gartrell, C. A. (2007b). “Full-scale instrumented testing and analysis of matting systems for airfield parking ramps and taxiways.” Rep. ERDC/GSL TR-07-33, U.S. Army COE (USACE), Engineer Research and Development Center, Vicksburg, MS.
Gartrell, C. A., Newman, J. K., and Anderton, G. L. (2009). “Performance measurements of pavement matting systems by full-scale testing over differing soil strengths.” J. Mater. Civ. Eng., 561–568.
Gonzalez, C. R., and Rushing, T. W. (2009). “Development of a new design methodology for structural airfield mats.” Proc., Transportation Research Board 88th Annual Meeting (DVD-ROM), Transportation Research Board, Washington, DC.
Hua, J., and White, T. (2002). “A study of nonlinear tire contact pressure effects on HMA rutting.” Int. J. Geomech., 353–376.
Murphy, G. (1935). “Stresses and deflections in loaded rectangular plates on elastic foundations.” Bulletin No. 135, Iowa Engineering Experiment Station, Iowa State Univ., Ames, IA.
Sheng, D., Wriggers, P., and Sloan, S. W. (2007). “Application of frictional contact in geotechnical engineering.” Int. J. Geomech., 176–185.
Stroble, M. F. (2009). “Analysis and design of wood construction platforms using instrumentation.” M.S. thesis, Mississippi State Univ., Mississippi State, MS.
U.S. Air Force (USAF). (1997). “Criteria and guidance for C-17 contingency and training operations on semi-prepared airfields.” Engineering Technical Letter (ETL) 97-9, Washington, DC.
White, T. D. (1971). “Theoretical landing mat analysis.” Miscellaneous Paper No. S-71-21, U.S. Army COE (USACE) Waterways Experiment Station, Vicksburg, MS.
William, G. W., and Shoukry, S. N. (2001). “3D finite element analysis of temperature-induced stresses in dowel jointed concrete pavements.” Int. J. Geomech., 291–307.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: May 10, 2011
Accepted: Nov 21, 2012
Published online: Nov 22, 2012
Published in print: Apr 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.