Abstract
Wood biomass is widely used as fuel in the so-called green power units producing heat and electricity. Wood biomass, like other solid fuels, contains many elements, most of which are found in trace amounts. The bark of Mediterranean pine cleaned of wood was chosen for the study presented in this paper. Thirty-five elements, of which 19 are trace elements (TEs), were identified in the pine bark. An experimental study on the ground pine bark burning at temperatures 650°C, 750°C, 850°C, and 950°C was conducted on a laboratory scale. Ashes formed from combustion at particular temperatures were analyzed. Experimental results and calculations of thermodynamic equilibrium were compiled in the form of a series of small graphs for major elements, minor ones, and TEs present in ashes, which allows quick evaluation of the results of the study. The consequence of an increase in the combustion temperature was the reduction of the content of K, S, Cu, and Pb in ash. TEs with the highest retention in ashes included Co, V, Cr, Sr, Ba, and Ni. The thermodynamic equilibrium calculations performed in the FactSage software version 6.3 made it possible to predict the occurrence of major, minor, and trace elements in ashes and flue gas.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Science Center (Poland) within the “MINIATURA 1” Project No. 2017/01/X/ST8/00127.
References
Abanades, S., G. Flamant, and D. Gauthier. 2001. “Modelling of heavy metal vaporization from a mineral matrix.” J. Hazard. Mater. B88 (1): 75–94. https://doi.org/10.1016/S0304-3894(01)00298-9.
Abanades, S., G. Flamant, and D. Gauthier. 2002. “Kinetics of heavy metal vaporization from model wastes in a fluidized bed.” Environ. Sci. Technol. 36 (17): 3879–3884. https://doi.org/10.1021/es020037e.
Bale, C. W., et al. 2016. “FactSage thermochemical software and databases, 2010-2016.” Calphad 54 (Sep): 35–53. https://doi.org10.1016/j.calphad.2016.05.002.
Barbosa, R., D. Dias, N. Lapa, H. Lopes, and B. Mendes. 2013. “Chemical and ecotoxicological properties of size fractionated biomass ashes.” Fuel Process. Technol. 109 (May): 124–132. https://doi.org/10.1016/j.fuproc.2012.09.048.
Bashir, M. S., P. A. Jensen, F. J. Frandsen, S. Wedel, K. Dam-Johansen, J. Wadenbäck, and S. T. Pedersen. 2012. “Suspension-firing of biomass. Part 1: Full-scale measurements of ash deposit build-up.” Energy Fuels 26 (4): 2317–2330. https://doi.org/10.1021/ef201680k.
Bogush, A. A., J. A. Stegemann, R. Williams, and I. G. Wood. 2018. “Element speciation in UK biomass power plant residues based on composition, mineralogy, microstructure and leaching.” Fuel 211 (Jan): 712–725. https://doi.org/10.1016/j.fuel.2017.09.103.
Caillat, S., and E. Vakkilainen. 2013. “Large-scale biomass combustion plants: An overview.” In Biomass combustion science, technology and engineering: Woodhead Publishing series in energy, edited by L. Rosendahl, 189–224. Oxford, UK: Woodhead Publishing.
Contreras, M. L., J. M. Arostegui, and L. Armesto. 2009. “Arsenic interactions during co-combustion processes based on thermodynamic equilibrium calculations.” Fuel 88 (3): 539–546. https://doi.org/10.1016/j.fuel.2008.09.028.
Dahl, O., H. Nurmesniemi, R. Pöykiö, and G. Watkins. 2010. “Heavy metal concentrations in bottom ash and fly ash fractions from a large-sized (246 MW) fluidized bed boiler with respect to their Finnish forest fertilizer limit values.” Fuel Process. Technol. 91 (11): 1634–1639. https://doi.org/10.1016/j.fuproc.2010.06.012.
Frandsen, F., K. Dam-Johansen, and P. Rasmussen. 1994. “Trace elements from combustion and gasification of coal—An equilibrium approach.” Prog. Energy Combust. Sci. 20 (2): 115–138. https://doi.org/10.1016/0360-1285(94)90007-8.
Furimsky, E. 2000. “Characterization of trace element emissions from coal combustion by equilibrium calculations.” Fuel Process. Technol. 63 (1): 29–44. https://doi.org/10.1016/S0378-3820(99)00067-3.
Helble, J. J. 1994. “Trace element behavior during coal combustion: Results of a laboratory study.” Fuel Process. Technol. 39 (1–3): 159–172. https://doi.org/10.1016/0378-3820(94)90178-3.
Hupa, M., O. Karlström, and E. Vainio. 2017. “Biomass combustion technology development—It is all about chemical details.” Proc. Combust. Inst. 36 (1): 113–134. https://doi.org/10.1016/j.proci.2016.06.152.
Jerzak, W. 2017. “Thermodynamic prediction of the effect of excess air ratios and combustion temperatures on the equilibrium phases formed during ash fusion from coal and cedar nut shells.” Energy Fuels 31 (11): 12756–12769. https://doi.org/10.1021/acs.energyfuels.7b01563.
Jiménez, S., M. Pérez, and J. Ballester. 2008. “Vaporization of trace elements and their emission with submicrometer aerosols in biomass combustion.” Energy Fuels 22 (4): 2270–2277. https://doi.org/10.1021/ef800111u.
Kimura, K., Y. Shimizu, and J. Hayashi. 1995. “12: Structural change of cellulose polymorphs by milling.” In Cellulose and cellulose derivatives, edited by J. F. Kennedy, G. O. Phillips, and P. A. Williams, 85–92. Cambridge, MA: Woodhead Publishing.
Lundholm, K., D. Boström, A. Nordin, and A. Shchukarev. 2007. “Fate of Cu, Cr, and As during combustion of impregnated wood with and without peat additive.” Environ. Sci. Technol. 41 (18): 6534–6540. https://doi.org/10.1021/es0630689.
Mason, P. E., L. I. Darvell, J. M. Jones, and A. Williams. 2016. “Observations on the release of gas-phase potassium during the combustion of single particles of biomass.” Fuel 182 (Oct): 110–117. https://doi.org/10.1016/j.fuel.2016.05.077.
Ménard, Y., A. Asthana, F. Patisson, P. Sessiecq, and D. Ablitzer. 2006. “Thermodynamic study of heavy metals behaviour during municipal waste incineration.” Process Saf. Environ. Prot. 84 (4): 290–296. https://doi.org/10.1205/psep.05166.
Miller, B. B., R. Kandiyoti, and D. R. Dugwell. 2002. “Partitioning of trace elements during the combustion of coal and biomass in a suspension-firing reactor.” Fuel 81 (2): 159–171. https://doi.org/10.1016/S0016-2361(01)00134-X.
Nzihou, A., and B. Stanmore. 2013. “The fate of heavy metals during combustion and gasification of contaminated biomass—A brief review.” J. Hazard. Mater. 256–257 (Jul): 56–66. https://doi.org/10.1016/j.jhazmat.2013.02.050.
Obernberger, I., F. Biedermann, W. Widmann, and R. Riedl. 1997. “Concentrations of inorganic elements in biomass fuels and recovery in the different ash fractions.” Biomass Bioenergy 12 (3): 211–224. https://doi.org/10.1016/S0961-9534(96)00051-7.
Perry, D. L. 2011. Handbook of inorganic compounds. Boca Raton, FL: CRC Press.
Ragland, K. W., D. J. Aerts, and A. J. Baker. 1991. “Properties of wood for combustion analysis.” Bioresour. Technol. 37 (2): 161–168. https://doi.org/10.1016/0960-8524(91)90205-X.
Richaud, R., A. A. Herod, and R. Kandiyoti. 2004. “Comparison of trace element contents in low-temperature and high-temperature ash from coals and biomass.” Fuel 83 (14–15): 2001–2012. https://doi.org/10.1016/j.fuel.2004.05.009.
Ruscio, A., F. Kazanc, and Y. A. Levendis. 2016. “Comparison of fine ash emissions generated from biomass and coal combustion and valuation of predictive furnace deposition indices: A review.” J. Energy Eng. 142 (2): E4015007. https://doi.org/10.1061/(ASCE)EY.1943-7897.0000310.
Saqib, N., and M. Bäckström. 2014. “Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.” Waste Manage. 34 (12): 2505–2519. https://doi.org/10.1016/j.wasman.2014.08.025.
Świetlik, R., M. Trojanowska, M. Łożyńska, and A. Molik. 2014. “Impact of solid fuel combustion technology on valence speciation of chromium in fly ash.” Fuel 137 (Dec): 306–312. https://doi.org/10.1016/j.fuel.2014.08.010.
Tangahu, B. V., S. R. S. Abdullah, H. Basri, M. Idris, N. Anuar, and M. Mukhlisin. 2011. “A review on heavy metals (As, Pb, and Hg) uptake by plants through phytoremediation.” Int. J. Chem. Eng. 2011: 1–31. https://doi.org/10.1155/2011/939161.
Vassilev, S. V., D. Baxter, L. K. Andersen, and C. G. Vassileva. 2010. “An overview of the chemical composition of biomass.” Fuel 89 (5): 913–933. https://doi.org/10.1016/j.fuel.2009.10.022.
Vassilev, S. V., C. G. Vassileva, and D. Baxter. 2014. “Trace element concentrations and associations in some biomass ashes.” Fuel 129 (Aug): 292–313. https://doi.org/10.1016/j.fuel.2014.04.001.
Verhulst, D., A. Buekens, P. J. Spencer, and G. Eriksson. 1995. “Thermodynamic behavior of metal chlorides and sulfates under the conditions of incineration furnaces.” Environ. Sci. Technol. 30 (1): 50–56. https://doi.org/10.1021/es940780+.
Wiinikka, H., C. Gro¨nberg, and C. Boman. 2013. “Emissions of heavy metals during fixed-bed combustion of six biomass fuels.” Energy Fuels 27 (2): 1073–1080. https://doi.org/10.1021/ef3011146.
Xing, P., L. I. Darvell, J. M. Jones, L. Mab, M. Pourkashanian, and A. Williams. 2016. “Experimental and theoretical methods for evaluating ash properties of pine and El Cerrejon coal used in co-firing.” Fuel 183 (Nov): 39–54. https://doi.org/10.1016/j.fuel.2016.06.036.
Yao, X., K. Xu, F. Yan, and Y. Linag. 2017. “The influence of ashing temperature on ash fouling and slagging characteristics during combustion of biomass fuels.” BioResources 12 (1): 1593–1610. https://doi.org/10.15376/biores.12.1.1593-1610.
Zevenhoven, R., and P. Kilpinen. 2001. “Trace elements, alkali metals.” Chap. 8 in Control of pollutants in flue gases and fuel gases, 1–30. Espoo, Finland: Helsinki Univ. of Technology.
Zhang, R., X. Jiang, Y. Chi, and J. Yan. 2016. “Experimental and thermodynamic study of the partition of Cr, Ni, Cu, Pb, and Mn during co-combustion of pickling sludge and bituminous coal.” Energy Fuels 30 (1): 690–697. https://doi.org/10.1021/acs.energyfuels.5b02213.
Zheng, W., X. Ma, Y. Tang, C. Ke, and Z. Wu. 2018. “Heavy metal control by natural and modified limestone during wood sawdust combustion in a atmosphere.” Energy Fuels 32 (2): 2630–2637. https://doi.org/10.1021/acs.energyfuels.7b03365.
Zhu, Y., J. Hu, W. Yang, W. Zhang, K. Zeng, H. Yang, S. Du, and H. Chen. 2018. “Ash fusion characteristics and transformation behaviors during bamboo combustion in comparison with straw and poplar.” Energy Fuels 32 (4): 5244–5251. https://doi.org/10.1021/acs.energyfuels.8b00371.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Oct 2, 2018
Accepted: Apr 18, 2019
Published online: Oct 18, 2019
Published in print: Feb 1, 2020
Discussion open until: Mar 18, 2020
ASCE Technical Topics:
- Ashes
- Biomass
- Building materials
- Chemical compounds
- Chemical elements
- Chemical processes
- Chemicals
- Chemistry
- Combustion
- Energy engineering
- Energy sources (by type)
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Environmental engineering
- Equilibrium
- Fuels
- Materials engineering
- Measurement (by type)
- Non-renewable energy
- Statics (mechanics)
- Temperature effects
- Temperature measurement
- Thermodynamics
- Trace elements
- Wood and wood products
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.