Effect of Exhaust Gas Recirculation on the Combustion and Emissions of Dimethyl Ether in a Passenger Vehicle Diesel Engine
Publication: Journal of Energy Engineering
Volume 144, Issue 5
Abstract
The purpose of this work was to investigate the effect of the combustion and emission characteristics of dimethyl ether (DME), diesel fuel, and a DME-biodiesel blend on a passenger vehicle diesel engine. In this study, DME properties, atomization characteristics, and effects of the exhaust gas recirculation (EGR) rate on the combustion performance and emission characteristics of a diesel engine were investigated under single and split injection. The results show that DME atomization is better than that of conventional diesel fuel, and that increasing the EGR rate decreases the combustion pressure and heat release rate of the DME-biodiesel blend. Upon comparison, the maximum pressures of the pilot injections were significantly lower than those of the single injection for the DME-biodiesel. In addition, the maximum pressure decreased with the increasing EGR rate. However, the decrease was small compared with that of the pilot injection strategy. Exhaust emissions from the engine showed that increasing the EGR rate decreased combustion pressure and nitrogen oxide emissions, and increased hydrocarbon and carbon monoxide emissions. The soot was almost zero for the DME-biodiesel fuel and for the EGR rate variations.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by the Basic Science Research Program (Nos. 2017R1D1A1B03035064 and 2016R1D1A3B03935537) and the Basic Research Laboratory Program (No. 2015R1A4A1041746) through the National Research Foundation of Korea (NRF) funded by the Ministry of Education.
References
Arya, P. K., S. Tupkari, K. Satish, G. D. Thakre, and B. M. Shukla. 2016. “DME blended LPG as a cooking fuel option for Indian household. A review.” Renewable Sustainable Energy Rev. 53 (Jan): 1591–1601. https://doi.org/10.1016/j.rser.2015.09.007.
Bhide, S., D. Morris, J. Leroux, K. S. Wain, J. M. Perez, and A. L. Boehman. 2003. “Characterization of the viscosity of blends of dimethyl ether with various fuels and additives.” Energy Fuel 17 (5): 1126–1132. https://doi.org/10.1021/ef030055x.
BP (British Petroleum). 2016. BP statistical review of world energy. London: BP.
Canakci, M. 2007. “Combustion characteristics of a turbocharged DI compression ignition engine fueled with petroleum diesel fuels and biodiesel.” Bioresour. Technol. 98 (6): 1167–1175. https://doi.org/10.1016/j.biortech.2006.05.024.
Cipolat, D., and D. Valentim. 2013. “Comparison of theoretical and experimental diesel and DME injection spray characteristics.” Fuel Process Technol. 107 (Mar): 36–43. https://doi.org/10.1016/j.fuproc.2012.07.017.
Gill, D., and H. Ofner. 1995. Dimethyl ether—A clean fuel for transportation. Warrendale, PA: SAE International.
IEA (International Energy Agency). 2016. CO2 emission from fuel combustion highlights. IEA 10-21. Paris: IEA.
Kim, H. J., H. K. Suh, and C. S. Lee. 2008a. “Numerical and experimental study on the comparison between diesel and dimethyl ether (DME) spray behaviors according to combustion chamber shape.” Energy Fuels 22 (4): 2851–2860. https://doi.org/10.1021/ef8000696.
Kim, M. Y., S. H. Yoon, and C. S. Lee. 2008b. “Impact of split injection strategy on the exhaust emissions and soot particulates from a compression ignition engine fueled with neat biodiesel.” Energy Fuel 22 (2): 1260–1265. https://doi.org/10.1021/ef700537w.
Kim, M. Y., S. H. Yoon, B. W. Ryu, and C. S. Lee. 2008c. “Combustion and emission characteristics of DME as an alternative fuel for compression ignition engines with a high pressure injection system.” Fuel 87 (12): 2779–2786. https://doi.org/10.1016/j.fuel.2008.01.032.
Lapuerta, M., J. Rodríguez-Fernández, D. Fernández-Rodríguez, and R. Patiño-Camino. 2017. “Modeling viscosity of butanol and ethanol blends with diesel and biodiesel fuels.” Fuel 199 (Jul): 332–338. https://doi.org/10.1016/j.fuel.2017.02.101.
Lattimore, T., C. Wang, H. Xu, M. L. Wyszynski, and S. Shuai. 2016. “Investigation of EGR effect on combustion and PM emissions in a DISI engine.” Appl. Energy 161 (Jan): 256–267. https://doi.org/10.1016/j.apenergy.2015.09.080.
Lee, D., and C. S. Lee. 2017. “Effects of DME-isobutane blended fuels on combustion and emissions reduction in a passenger car diesel engine.” J. Energy Eng. 143 (4): 04017003. https://doi.org/10.1061/(ASCE)E.y.1943-7897.0000428.
Park, S. H., H. J. Kim, H. K. Suh, and C. S. Lee. 2009. “An experimental and numerical analysis of spray-atomization characteristics of biodiesel fuel in various fuels and ambient temperature conditions.” Int. J. Heat Fluid Flow 30 (5): 960–970. https://doi.org/10.1016/j.ijheatfluidflow.2009.04.003.
Park, S. H., and C. S. Lee. 2013. “Combustion and emission reduction characteristics of automotive DME engine system.” Prog. Energy Combust. 39 (1): 147–168. https://doi.org/10.1016/j.pecs.2012.10.002.
Park, S. H., and C. S. Lee. 2014. “Applicability of dimethyl ether in a compression ignition engine as an alternative fuel.” Energy Convers. Manage. 86 (Oct): 848–863. https://doi.org/10.1016/j.enconman.2014.06.051.
Park, S. H., I. M. Youn, and C. S. Lee. 2011. “Influence of ethanol blends on the combustion performance and exhaust emission characteristics of a four-cylinder diesel engine at various engine loads and injection timings.” Fuel 90 (2): 748–755. https://doi.org/10.1016/j.fuel.2010.08.029.
Rakopoulos, C. D., K. A. Antonopoulos, and D. C. Ralopoulos. 2007. “Experimental heat release analysis and emission of a HSDI diesel engine fueled with ethanol-diesel fuel blends.” Energy 32 (10): 1791–1808. https://doi.org/10.1016/j.energy.2007.03.005.
Rakopoulos, D. C. 2015. “Comparison of combustion, performance, and emissions of HSDI diesel engine operating on blends of diesel fuel with ethanol, n-butanol, or butanol isomer ether DEE.” J. Energy Eng. 141 (2): C4014001. https://doi.org/10.1061/(ASCE)EY.1943-7897.0000210.
Rakopoulos, D. C., C. D. Rakopoulos, E. G. Giakoumis, N. P. Komnois, G. M. Kosmadakis, and R. G. Papakiannakis. 2017. “Comparative evaluation of ethanol, n-butanol, and diethyl ether effects as biofuel supplements on combustion characteristics, cyclic variations, and emissions balance in light duty-diesel engine.” J. Energy Eng. 143 (20): 04016044. https://doi.org/10.1061/(ASCE)Ey.1943-7897.0000399.
Rakopoulos, D. C., C. D. Rakopoulos, E. G. Giakoumis, R. G. Papagiannakis, and D. C. Kyritsis. 2008. “Experimental-stochastic investigation of the combustion cycle variability in HSDI diesel engine using ethanol-diesel fuel blends.” Fuel 87 (8–9): 1478–1491. https://doi.org/10.1016/j.fuel.2007.08.012.
Rakopoulos, D. C., C. D. Rakopoulos, and D. C. Kyritsis. 2016. “Butanol or DEE blends with either straight vegetable oil or biodiesel excluding fossil fuel: Comparative effects on diesel engine combustion attributes, cyclic variability and regulated emission trade-off.” Energy 115 (Nov): 314–325. https://doi.org/10.1016/j.energy.2016.09.022.
Ryu, B. W., D. Lee, H. G. Roh, and C. S. Lee. 2015. “Effect of a dimethyl ether-soybean methyl ester blend as an alternative fuel on the combustion and the distribution of nitrogen oxide emissions and soot emissions in a passenger car diesel engine.” Proc. Inst. Mech. Eng. Part D: J. Automobile Eng. 230 (9): 1254–1263. https://doi.org/10.1177/0954407015605934.
Sivebaek, I. M., S. C. Sorenson, and J. Jakobsen. 2001. Dimethyl ether (DME)—Assessment of viscosity using the new volatile fuel viscometer (VFVM). Warrendale, PA: SAE International.
Stone, R. 1999. Introduction to internal combustion engines. Warrendale, PA: SAE International.
Suh, H. K., and C. S. Lee. 2008. “Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system.” Fuel 87 (6): 925–932. https://doi.org/10.1016/j.fuel.2007.05.051.
Suh, H. K., and C. S. Lee. 2016. “A review on atomization and exhaust emissions of a biodiesel-fueled compression ignition engine.” Renewable Sustainable Energy Rev. 58 (May): 1601–1620. https://doi.org/10.1016/j.rser.2015.12.329.
Teng, H., J. C. McCandless, and J. B. Schneyer. 2001. Thermochemical characteristics of dimethyl ether—An alternative fuel for compression-ignition engines. Warrendale, PA: SAE International.
Thomas, G., B. Feng, A. Veeraragavan, M. J. Cleary, and N. Drinnan. 2014. “Emissions from DME combustion in diesel engines and their implications on meeting future emission norms: A review.” Fuel Process Technol. 119 (Mar): 286–304. https://doi.org/10.1016/j.fuproc.2013.10.018.
Varghese, R. J., V. Ratna Kishore, M. Akram, Y. Yoon, and S. Kumar. 2017. “Burning velocities of DME (dimethyl ether)-air premixed flames at elevated temperatures.” Energy 126 (May): 34–41. https://doi.org/10.1016/j.energy.2017.03.004.
Wang, Y., G. Li, W. Zhu, and L. Zhou. 2008. “Study on the application of DME/diesel blends in a diesel engine.” Fuel Process Technol. 89 (12): 1272–1280. https://doi.org/10.1016/j.fuproc.2008.05.023.
Zhao, Y., Y. Wang, D. Li, X. Lei, and S. Liu. 2014. “Combustion and emission characteristics of a DME (dimethyl ether)-diesel dual fuel premixed charge compression ignition engine with EGR (exhaust gas recirculation).” Energy 72 (Jul): 608–617. https://doi.org/10.1016/j.energy.2014.05.086.
Zheng, M., M. C. Mulenga, G. T. Reader, M. Wang, D. S.-K. Ting, and J. Tjong. 2008. “Biodiesel engine performance and emissions in low temperature combustion.” Fuel 87 (6): 714–722. https://doi.org/10.1016/j.fuel.2007.05.039.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Nov 26, 2017
Accepted: May 8, 2018
Published online: Aug 15, 2018
Published in print: Oct 1, 2018
Discussion open until: Jan 15, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.