Spray Characteristics of n-Butanol in a High-Pressure Common-Rail Injection System
Publication: Journal of Energy Engineering
Volume 143, Issue 5
Abstract
This study was conducted to investigate the spray characteristics of n-butanol, using a diesel spray for comparison. Spray tip penetration and spray cone angle were tested and analyzed. A high-speed photographic system was employed to observe the spray evolution, and a common-rail system and constant-volume chamber were used to change the pressure. The results show that the n-butanol spray penetrates faster than the diesel spray while under the same conditions. The experimental trend lines support the axial development model constructed by Hiroyasu and Arai on the grounds of a similar proportional relation to time after the start of injection, and the empirical equations provide reasonable approximations to the experimental measurements of the spray tip penetration.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (No. 51376171).
References
Agathou, M. S., and Kyritsis, D. C. (2012a). “Electrostatic atomization of hydrocarbon fuels and bio-alcohols for engine applications.” Energy Convers. Manage., 60(8), 10–17.
Agathou, M. S., and Kyritsis, D. C. (2012b). “Fuel composition effect on the electrostatically-driven atomization of bio-butanol containing engine fuel blends.” Energy Convers. Manage., 60(8), 28–35.
Agathou, M. S., and Kyritsis, D. C. (2014). “Experimental study of steady quasi-cone-jet electrostatic sprays of biobutanol for engine applications.” J. Energy Eng., A4014008.
Aleiferis, P. G., and Romunde, V. Z. R. (2013). “An analysis of spray development with iso-octane, n-pentane, gasoline, ethanol and n-butanol from a multi-hole injector under hot fuel conditions.” Fuel, 105(2), 143–168.
Baumgarten, C. (2006). Mixture formation in internal combustion engine, Springer, Heidelberg.
Bougie, B., Tulej, M., Dreier, T., Dam, N. J., Meulen, J. J. T., and Gerber, T. (2005). “Optical diagnostics of diesel spray injections and combustion in a high-pressure high-temperature cell.” Appl. Phys. B, 80(8), 1039–1045.
Chen, P. C., Wang, W. C., Roberts, W. L., and Fang, T. (2013). “Spray and atomization of diesel fuel and its alternatives from a single-hole injector using a common rail fuel injection system.” Fuel, 103(2), 850–861.
Dean, J. A. (1979). Lange’s handbook of chemistry, McGraw Hill, New York.
Delphi [Computer software]. Embarcadero, CA.
Emberson, D. R., Ihracska, B., Imran, S., and Diez, A. (2016). “Optical characterization of diesel and water emulsion fuel injection sprays using shadowgraphy.” Fuel, 172, 253–262.
Ezeji, T. C., Qureshi, N., and Blaschek, H. P. (2005). “Continuous butanol fermentation and feed starch retrogradation: butanol fermentation sustainability using Clostridium beijerinckii BA101.” J. Biotechnol., 115(2), 179–187.
Freeman, J., Williams, J., Minner, S., Baxter, C., Dejovine, J., Gibbs, L., et al. (1988). Alcohols and ethers: A technical assessment of their application as fuels and fuel components, API Publications, New York.
Hiroyasu, H., and Arai, M. (1990). “Structures of fuel sprays in diesel engines.”, Society of Automotive Engineers, Warrendale, PA.
Li, Y. F., Guo, H. J., Wang, J. X., and Xu, H. M. (2014). “The comparative study of gasoline and n-butanol on spray characteristics.”, Society of Automotive Engineers, Warrendale, PA.
Li, Y. F., and Xu, H. M. (2016). “Experimental study of temporal evolution of initial stage diesel spray under varied conditions.” Fuel, 171(4), 44–53.
Liu, H. F., Bi, X. J., Huo, M., Lee, C. F., and Yao, M. F. (2012). “Soot emissions of various oxygenated biofuels in conventional diesel combustion and low-temperature combustion conditions.” Energ. Fuel., 26(3), 1900–1911.
Liu, H. F., Lee, C. F., Huo, M., and Yao, M. F. (2011). “Comparison of ethanol and butanol as additives in soybean biodiesel using a constant volume combustion chamber.” Energ. Fuel., 25(4), 1837–1846.
Marchitto, L., Merola, S., Tornatore, C., and Valentino, G. (2014). “Experimental study on the spray atomization of a multi-hole injector for spark ignition engines fuelled by gasoline and n-butanol.”, Society of Automotive Engineers, Warrendale, PA.
Mo, J., Tang, C. L., Li, J. G., Guan, L., and Huang, Z. H. (2016). “Experimental investigation on the effect of n-butanol blending on spray characteristics of soybean biodiesel in a common-rail fuel injection system.” Fuel, 182, 391–401.
Naber, J. D., and Siebers, D. L. (1996). “Effects of gas density and vaporization on penetration and dispersion of diesel sprays.”, Society of Automotive Engineers, Warrendale, PA.
Ohnesorge, W. V. (1936). “Die bildung von tropfen an düsen und die auflösung flüssiger strahlen.” Zamm J. Appl. Math. Mech./Zeitschrift Für Angewandte Mathematik Und Mechanik, 16(6), 355–358.
Rakopoulos, D. C., Rakopoulos, C. D., Giakoumis, E. G., Papagiannakis, R. G., and Kyritsis, D. C. (2014). “Influence of properties of various common bio-fuels on the combustion and emission characteristics of high-speed DI (direct injection) diesel engine: Vegetable oil, bio-diesel, ethanol, n-butanol, diethyl ether.” Energy, 73(9), 354–366.
Rakopoulos, D. C., Rakopoulos, C. D., and Kyritsis, D. C. (2016). “Butanol or DEE blends with either straight vegetable oil or biodiesel excluding fossil fuel: Comparative effects on diesel engine combustion attributes, cyclic variability and regulated emissions trade-off.” Energy, 115(1), 314–325.
Rakopoulos, D. C., Rakopoulos, C. D., Papagiannakis, R. G., and Kyritsis, D. C. (2011). “Combustion heat release analysis of ethanol or n-butanol diesel fuel blends in heavy-duty DI diesel engine.” Fuel, 90(5), 1855–1867.
Reitz, R. D., and Bracco, F. V. (1986). “Mechanisms of breakup of round liquid jets.” Encycl. Fluid Mech., 3, 233–249.
Song, L. B., Lin, Q. Z., Xie, Y. Z., Hu, H. W., Hu, H. Q., Pi, D., and Xu, S. M. (2015). “Experimental study of the spray characteristics of diesohol fuel using a high pressure common rail injection system in a diesel engine.” Energy Technol., 3(9), 896–905.
Wigg, B. R., Coverdill, R. E., Lee, C. F., and Kyritsis, D. C. (2011). “Emissions characteristics of neat butanol fuel using a port fuel-injected, spark-ignition engine.”, Society of Automotive Engineers, Warrendale, PA.
Xie, H. Z., Lin, Q. Z., Song, L. B., Xie, Y. Z., Pi, D., and Shao, C. Y. (2015). “An experimental study on the macroscopic spray characteristics of biodiesel and diesel in a constant volume chamber.” Energies, 8(6), 5952–5972.
Yanai, T., Han, X., Reader, G. T., Zheng, M., and Tjong, J. (2015). “Preliminary investigation of direct injection neat n-butanol in a diesel engine.” J. Energ. Resour., 137(1), 012205.
Zannis, T., Hountalas, D. T., and Kouremenos, D. A. (2004). “Experimental investigation to specify the effect of oxygenated additive content and type on DI diesel performance and emissions.” SAE Inj. J. Fuels Lubr., 4(4), 166–179.
Zheng, M., Li, T., and Han, X. (2015). “Direct injection of neat n-butanol for enabling clean low temperature combustion in a modern diesel engine.” Fuel, 142(3), 28–37.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Dec 5, 2016
Accepted: Mar 24, 2017
Published online: Jun 28, 2017
Published in print: Oct 1, 2017
Discussion open until: Nov 28, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.