Role of Cerium Oxide Nanoparticles as Diesel Additives in Combustion Efficiency Improvements and Emission Reduction
Publication: Journal of Energy Engineering
Volume 142, Issue 4
Abstract
An experimental investigation is conducted to evaluate the performance, combustion, and emission characteristics of a diesel engine using cerium oxide () nanoparticles as diesel fuel additives. Using cetyl trimethyl ammonium bromide (CTAB) as the cationic surfactant and with ultrasonic vibration, nanoparticles at dosing levels of 50 and can be stably and uniformly dispersed in diesel. Physically, the mixing of fuel blends with air is enhanced by microexplosion events because of the large surface-volume ratio and intensified thermal transmissibility of nanoparticles. Moreover, chemically, in diesel fuel plays a positive role in the dehydrogenation reaction at a high temperature because of its excellent redox ability. As a result, the addition of to neat diesel (50 and ) leads to a gradual increase in the cylinder pressure compared with the reference neat diesel. Meanwhile, the ignition of fuel blends with a high dosing level of occurs earlier by approximately 1.2° crank angle (CA) and 1.8°CA, respectively. At full load, the effective thermal efficiencies for fuels are augmented by approximately 1.7 and 2.3%. Because of the distinctive merits of in promoting fuel atomization and its favorable intrinsic catalytic effect, the level of harmful pollutants (such as HC, CO, , and soot) in exhaust gases is appreciably reduced to varying degrees.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to express their appreciation for the funds from the National Natural Science Foundation of China (No. 51376083 and No. 51376095) and the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD), which supported this study.
References
Basha, J. S., and Anand, R. B. (2011a). “An experimental investigation in a diesel engine using carbon nanotubes blended water-diesel emulsion fuel.” Proc. Inst. Mech. Eng., Part A, 225(3), 279–288.
Basha, J. S., and Anand, R. B. (2011b). “An experimental study in a CI engine using nanoadditive blended water-diesel emulsion fuel.” Int. J. Green Energy, 8(3), 332–348.
Basha, J. S., and Anand, R. B. (2011c). “Role of nanoadditive blended biodiesel emulsion fuel on the working characteristics of a diesel engine.” J. Renewable Sustainable Energy, 3(2), 3106–3123.
Basha, J. S., and Anand, R. B. (2014). “Performance, emission and combustion characteristics of a diesel engine using carbon nanotubes blended jatropha methyl ester emulsions.” Alexandria Eng. J., 53(2), 259–273.
Bozek, F., Dvorak, J., and Mares, J. (2011a). “Emissions of selected pollutants while applying of specific additive envirox™.” WSEAS Trans. Environ. Dev., 7(8), 233–243.
Bozek, F., Mares, J., and Bozek, M. (2011b). “Emission of particulate matter while applying the envirox™ additive.” 5th World Scientific and Engineering Academy and Society (WSEAS) Int. Conf. on Renewable Energy Sources: Recent Researches in Environment, Energy Planning and Pollution, Alexandru Ioan Cuza Univ., Iasi, Romania, 170–175.
Ganesh, D., and Gowrishankar, G. (2011). “Effect of nano-fuel additive on emission reduction in a biodiesel fuelled CI engine.” 2011 Int. Conf. on Electrical and Communication Engineering (ICECE), IEEE, 3453–3459.
Gürü, M., Karakaya, U., Altıparmak, D., and Alıcılar, A. (2002). “Improvement of diesel fuel properties by using additives.” Energy Convers. Manage., 43(8), 1021–1025.
Jiang, S., Teng, B., Yuan, J., Guo, X., and Luo, M. (2009). “Adsorption and oxidation of CO over surface.” Acta Phys. Chim. Sin., 25(8), 1629–1634.
Jung, H., Kittelson, D. B., and Zachariah, M. R. (2005). “The influence of a cerium additive on ultrafine diesel particulate emissions and kinetics of oxidation.” Combust. Flame, 142(3), 276–288.
Kao, M. J., Ting, C. C., Lin, B. F., and Tsung, T. T. (2008). “Aqueous aluminium nanofluid combustion in diesel fuel.” J. Test. Eval., 36(2), 100579.
Lapuerta, M., Armas, O., and Rodríguez-Fernández, J. (2008). “Effect of biodiesel fuels on diesel engine emissions.” Prog. Energy Combust. Sci., 34(2), 198–223.
Lawrence, N. J., et al. (2011). “Defect engineering in cubic cerium oxide nanostructures for catalytic oxidation.” Nano Lett., 11(7), 2666–2671.
Lemaire, J. (1999). “Eolys™ fuel-borne catalyst for diesel particulates abatement: A key component of an integrated system.”, 〈http://www.dieselnet.com/papers/9909rhodia/〉.
Luo, P., Nieh, T. G., Schwartz, A. J., and Lenk, T. J. (1995). “Surface characterization of nanostructured metal and ceramic particles.” Mater. Sci. Eng., A, 204(1), 59–64.
Miyamoto, N., Hou, Z., Harada, A., Ogawa, H., and Murayama, T. (1987). “Characteristics of diesel soot suppression with soluble fuel additives.”, Society of Automotive Engineers International, Warrendale, PA.
Monyem, A., Van Gerpen, J. H., and Canakci, M. (2001). “The effect of timing and oxidation on emissions from biodiesel fueled engines.” Trans. Am. Soc. Agric. Eng., 44(1), 35–42.
Ribeiro, N. M., et al. (2007). “The role of additives for diesel and diesel blended (ethanol or biodiesel) fuels: A review.” Energy Fuels, 21(4), 2433–2445.
Sajith, V., Sobhan, C. B., and Peterson, G. P. (2010). “Experimental investigations on the effects of cerium oxide nanoparticle fuel additives on biodiesel.” Adv. Mech. Eng., 2, 581407.
Selvan, V. A. M., Anand, R. B., and Udayakumar, M. (2014). “Effect of cerium oxide nanoparticles and carbon nanotubes as fuel-borne additives in diesterol blends on the performance, combustion and emission characteristics of a variable compression ratio engine.” Fuel, 130, 160–167.
Tyagi, H., et al. (2008). “Increased hot-plate ignition probability for nanoparticle-laden diesel fuel.” Nano Lett., 8(5), 1410–1416.
Valentine, J. M., Peter-Hoblyn, J. D., and Acres, G. K. (2000). “Emissions reduction and improved fuel economy performance from a bimetallic platinum/cerium diesel fuel additive at ultra-low dose rates.”, Society of Automotive Engineers International, Warrendale, PA.
Yetter, R. A., Risha, G. A., and Son, S. F. (2009). “Metal particle combustion and nanotechnology.” Proc. Combust. Inst., 32(2), 1819–1838.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Feb 2, 2015
Accepted: Sep 16, 2015
Published online: Dec 16, 2015
Discussion open until: May 16, 2016
Published in print: Dec 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.