Effects of Boost Pressure and Spark Timing on Performance and Exhaust Emissions in a Heavy-Duty Spark-Ignited Wood-Gas Engine
Publication: Journal of Energy Engineering
Volume 141, Issue 2
Abstract
Wood gas represents a viable energy source, particularly for stationary electric power generation, as it allows for a wide flexibility in fossil fuel sources and can be used as full supplement fuel in conventional heavy-duty (HD), turbocharged (T/C), spark-ignited (SI) engines. For such engines fuelled with wood gas, spark timing and boost pressure are critical parameters that affect both engine performance characteristics and NO and CO emissions. Thus, the main objective of this study is to investigate theoretically the effects of these parameters on the performance and exhaust emissions (NO and CO) of such an existing engine fueled with wood gas. The investigation is conducted by using a comprehensive two-zone phenomenological model. The predictive ability of model was tested against experimental measurements, which were obtained from the operation of such an engine fueled with wood-gas fuel under various operating conditions. The experimental results were found to be in good agreement with the respective computed ones obtained from the simulation model. From the comparative evaluation of the theoretical findings presented in this work, it is generally revealed that for a heavy-duty, turbocharged, SI wood-gas engine operating at 65% of (full) throttle valve opening (TVO), the increase of boost pressure accompanied by advanced spark timing could lead to a more efficient engine operation (i.e., decrease of the brake specific fuel consumption) with a slight improvement on its environmental behavior (i.e., decrease of specific NO and CO emissions). On the other hand, at 100% TVO engine operating point, the slight improvement of engine performance and environmental characteristics, which is achieved via the simultaneous increase of boost pressure and spark timing, is restricted by the occurrence of phenomena influencing its structural strength, because the maximum cylinder pressure becomes considerably higher compared to the respective one observed under normal spark timing and normal boost pressure operating mode.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors express their gratitude to the GE Jenbacher Company for supplying them with valuable experimental data.
References
Agarwal, A. K. (2007). “Biofuels (alcohols and biodiesel) applications as fuels for internal combustion engines.” Prog. Energy Combust. Sci., 33(3), 233–271.
Agathou, M. S., and Kyritsis, D. C. (2011). “An experimental comparison of non-premixed bio-butanol flames with the corresponding flames of ethanol and methane.” Fuel, 90(1), 255–262.
Agathou, M. S., and Kyritsis, D. C. (2013). “Experimental study of steady, quasi cone-jet electrostatic sprays of bio-butanol for engine applications.” J. Energy Eng., A4014008.
Ahrenfeldt, J., Schramm, J., and Jensen, T. K. (2001). “Experiments with wood gas engines.”, Society of Automotive Engineers International, Warrendale, PA.
Alkidas, A. C. (2007). “Combustion advancements in gasoline engines.” Energy Convers. Manage., 48(11), 2751–2761.
Ando, Y., Yoshikawa, K., Beck, M., and Endo, H. (2005). “Research and development of a low-BTU gas-driven engine for waste gasification and power generation.” Energy, 30(11–12), 2206–2218.
Annand, W. J. D. (1963). “Heat transfer in the cylinders of reciprocating internal combustion engines.” Proc. Inst. Mech. Eng., 177, 973–996.
Annand, W. J. D. (1970). “Geometry of spherical flame propagation in a disc-shaped combustion chamber.” J. Mech. Eng. Sci., 12(2), 146–149.
Arroyo, J., Moreno, F., Munoz, M., and Monne, C. (2013). “Efficiency and emissions of a spark ignition engine fueled with synthetic gases obtained from catalytic decomposition of biogas.” Int. J. Hydrogen Energy, 38(9), 3784–3792.
Benson, R. S., and Whitehouse, N. D. (1979). Internal combustion engines, Pergamon, Oxford, U.K.
Blizard, N. C., and Keck, J. C. (1974). “Experimental and theoretical investigation of turbulent burning model for internal combustion engines.”, Society of Automotive Engineers International, Warrendale, PA.
Chaudhari, S. T., Dalai, A. K., and Bakhshi, N. N. (2003). “Production of hydrogen and/or syngas (H2+CO) via steam gasification of biomass-derived chars.” Energy Fuels, 17(4), 1062–1067.
D’Andrea, T., Henshaw, P. F., and Ting, S. K. (2004). “The addition of hydrogen to a gasoline-fuelled SI engine.” Int. J. Hydrogen Energy, 29(14), 1541–1552.
Das, L. M., Gulati, R., and Gupta, P. K. (2000). “A comparative evaluation of the performance characteristics of a spark ignition engine using hydrogen and compressed natural gas as alternative fuels.” Int. J. Hydrogen Energy, 25(8), 783–793.
Debnath, B. K., Saha, U. K., and Sahoo, N. (2013a). “A theoretical route towards the estimation of second law potential of an emulsified palm biodiesel run diesel engine.” J. Energy Eng., A4014007.
Debnath, B. K., Sahoo, N., Bora, B. J., and Saha, U. K. (2013b). “Influence of emulsified palm biodiesel as a pilot fuel in a biogas run dual fuel diesel engine.” J. Energy Eng., A4014005.
Duret, A., Friedli, C., and Marechal, F. (2005). “Process design of synthetic natural gas (SNG) production using wood gasification.” J. Cleaner Prod., 13(15), 1434–1446.
Ferguson, C. R. (1986). Internal combustion engines, Wiley, New York.
Gajendra Babu, M. K., Prakash, G. T., and Subrahmanyam, J. P. (2001). “Experimental investigations on the performance characteristics of a producer gas-fueled spark ignition engine.”, Society of Automotive Engineers International, Warrendale, PA.
Garnier, C., Bilcan, A., Le Corre, O., and Rahmouni, C. (2005). “Characterisation of a syngas-diesel fuelled CI engine.”, Society of Automotive Engineers International, Warrendale, PA.
GE Jenbacher. (2005). “Laminar flame speed versus air fuel ratio—Experience in woodgas plants.” Technical Rep.
Giakoumis, E. G., Rakopoulos, C. D., Dimaratos, A. M., and Rakopoulos, D. C. (2013a). “Exhaust emissions with ethanol or n-butanol diesel fuel blends during transient operation: A review.” Renewable Sustainable Energy Rev., 17(1), 170–190.
Giakoumis, E. G., Rakopoulos, C. D., and Rakopoulos, D. C. (2013b). “An assessment of NOx emissions during transient diesel engine operation with biodiesel blends.” J. Energy Eng., A4014004.
Goncalves, C. K., Tenorio, J. A. S., Levendis, Y. A., and Carlson, J. B. (2008). “Emissions from the premixed combustion of gasified polyethylene.” Energy Fuels, 22(1), 372–381.
Gopal, G., Srinivasa Rao, P., Gopalakrishnan, K. V., and Murthy, B. S. (1982). “Use of hydrogen in dual-fuel engines.” Int. J. Hydrogen Energy, 7(3), 267–272.
Hara, T., et al. (2004). “Performance demonstration of gasification and power generation from woody biomass.” J. Jpn. Inst. Energy, 83(10), 815–820.
Heywood, J. B. (1988). Internal combustion engine fundamentals, McGraw-Hill, New York.
Huang, J., and Crookes, R. J. (1998). “Spark-ignition engine performance with simulated biogas: A comparison with gasoline and natural gas.” J. Inst. Energy, 71(489), 197–203.
Korakianitis, T., Namasivayam, A. M., and Crookes, R. J. (2011). “Natural-gas fuelled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions.” Prog. Energy Combust. Sci., 37(1), 89–112.
Labeckas, G., and Slavinskas, S. (2006). “The effect of rapeseed oil methyl ester on direct injection diesel engine performance and exhaust emissions.” Energy Convers. Manage., 47(13–14), 1954–1967.
Labeckas, G., Slavinskas, S., and Mazeika, M. (2014). “The effect of ethanol-diesel-biodiesel blends on combustion, performance and emissions of a direct injection diesel engine.” Energy Convers. Manage., 79, 698–720.
Lavoie, G. A., Heywood, J. B., and Keck, J. C. (1970). “Experimental and theoretical study of nitric oxide formation in internal combustion engines.” Combust. Sci. Technol., 1(4), 313–326.
Levendis, Y. A., Panagiotou, T., and Tasilm, M. E. (1990). “Development of a self-cleaning particle trap for diesel engine particulate control.”, Society of Automotive Engineers International, Warrendale, PA.
Li, J. D., Lu, Y. Q., and Du, T. S. (1986). “Improvement on the combustion of a hydrogen fueled engine.” Int. J. Hydrogen Energy, 11(10), 661–668.
Mitsingas, C. M., and Kyritsis, D. C. (2013). “Comparative evaluation of extinction through strain among three alcoholic butanol isomers in non-premixed counterflow flames.” J. Energy Eng., A4014006.
Munoz, M., Moreno, F., Morea-Roy, J., Ruiz, J., and Arauzo, J. (2000). “Low heating value gas on spark ignition engines.” Biomass Bioenergy, 18(5), 431–439.
Nagalingam, B., Duebel, F., and Scmillen, K. (1983). “Performance study using natural gas, hydrogen-supplemented natural gas and hydrogen in AVL research engine.” Int. J. Hydrogen Energy, 8(9), 715–720.
Papagiannakis, R. G., and Hountalas, D. T. (2002). “Theoretical and experimental investigation of a direct injection dual fuel diesel-natural gas engine.”, Society of Automotive Engineers International, Warrendale, PA.
Papagiannakis, R. G., Hountalas, D. T., Rakopoulos, C. D., and Rakopoulos, D. C. (2008). “Combustion and performance characteristics of a DI diesel engine operating from low to high natural gas supplement ratios at various operating conditions.”, Society of Automotive Engineers International, Warrendale, PA.
Papagiannakis, R. G., Rakopoulos, C. D., Hountalas, D. T., and Giakoumis, E. G. (2007). “Study of the performance and exhaust emissions of a spark-ignited engine operating on syngas fuel.” Int. J. Altern. Propul., 1(2–3), 190–215.
Papagiannakis, R. G., and Zannis, T. C. (2013). “Effect of wood-gas composition on performance and exhaust emission characteristics of a large spark-ignition engine.” J. Energy Eng., A4013002.
Pulkrabek, W. W. (2004). Engineering fundamentals of internal combustion engines, Pearson Prentice-Hall, NJ.
Rakopoulos, C. D., Dimaratos, A. M., Giakoumis, E. G., and Rakopoulos, D. C. (2009). “Evaluation of the effect of engine, load and turbocharger parameters on transient emissions of diesel engine.” Energy Convers. Manage., 50(9), 2381–2393.
Rakopoulos, C. D., and Giakoumis, E. G. (2009). Diesel engine transient operation—Principles of operation and simulation analysis, Springer, London.
Rakopoulos, C. D., and Michos, C. N. (2009). “Generation of combustion irreversibilities in a spark ignition engine under biogas-hydrogen mixtures fueling.” Int. J. Hydrogen Energy, 34(10), 4422–4437.
Rakopoulos, C. D., Michos, C. N., and Giakoumis, E. G. (2008). “Availability analysis of a syngas fueled spark ignition engine using a multi-zone combustion model.” Energy, 33(9), 1378–1398.
Rakopoulos, C. D., Rakopoulos, D. C., Giakoumis, E. G., and Dimaratos, A. M. (2010). “Investigation of the combustion of neat cottonseed oil or its neat bio-diesel in a HSDI diesel engine by experimental heat release and statistical analyses.” Fuel, 89(12), 3814–3826.
Rakopoulos, D. C., Rakopoulos, C. D., Giakoumis, E. G., and Dimaratos, A. M. (2012). “Characteristics of performance and emissions in high-speed direct injection diesel engine fueled with diethyl ether/diesel fuel blends.” Energy, 43(1), 214–224.
Rakopoulos, D. C., Rakopoulos, C. D., Giakoumis, E. G., Dimaratos, A. M., and Kakaras, E. C. (2013). “Comparative evaluation of two straight vegetable oils and their methyl ester bio-diesels as fuel extenders in HDDI diesel engine: Performance and emissions.” J. Energy Eng., A4014001.
Ramachandra, A. (1993). “Performace studies on a wood gas run IC engine—Recent advances in biomass gasification and combustion.” Proc., 4th National Meeting on Biomass Gasification and Combustion, Mysore, India.
Ramos, J. I. (1989). Internal combustion engine modeling, Hemisphere, New York.
Reitz, R. D. (2013). “Directions in internal combustion engine research.” Combust. Flame, 160(1), 1–8.
Sasauchi, K. (2005). “Application for electric generator by pyrolysis gasification of biomass.” J. Combust. Soc. Jpn., 47(139), 31–39.
Shashikantha, S., and Parikh, P. P. (1999). “Spark ignition producer gas engine and dedicated compressed natural gas engine-technology development and experimental performance optimization.”, Society of Automotive Engineers International, Warrendale, PA.
Shridar, G., Paul, P. J., and Mukunda, H. S. (2001). “Biomass derived producer gas as a reciprocating engine fuel—An experimental analysis.” Biomass Bioenergy, 21(1), 61–72.
Sobyanin, V., et al. (2005). “Syngas as a fuel for IC and diesel engines: Efficiency and harmful emissions cut-off.” Proc., Int. Hydrogen Energy Congress and Exposition, Istanbul, Turkey, 13–15.
Srinivasan, K. K., et al. (2006). “The advanced injection low pilot ignited natural gas engine: A combustion analysis.” Trans. ASME J. Eng. Gas Turbines Power, 128(1), 213–218.
Srinivasan, K. K., Krishnan, S. R., Qi, Y., Midkiff, K. C., and Yang, H. (2007). “Analysis of diesel pilot-ignited natural gas low-temperature combustion with hot exhaust gas recirculation.” Combust. Sci. Technol., 179(9), 1737–1776.
Vickland, C. W., Strange, F. M., Bell, R. A., and Starkman, E. S. (1962). “A consideration of the high temperature thermodynamics of internal combustion engines.” Trans. SAE, 70, 785–793.
Yamasaki, Y., Tomatsu, G., Nagata, Y., and Kaneko, S. (2007). “Development of a small size gas engine system with biomass gas (combustion characteristics of the wood chip pyrolysis gas.”, Society of Automotive Engineers International, Warrendale, PA.
Yun, K. T., Cho, H., Luck, R., and Mago, P. (2013). “Modeling of reciprocating internal combustion engines for power generation and heat recovery.” Appl. Energy, 102, 327–335.
Information & Authors
Information
Published In
Journal of Energy Engineering
Volume 141 • Issue 2 • June 2015
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 22, 2014
Accepted: Sep 30, 2014
Published online: Nov 10, 2014
Discussion open until: Apr 10, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.