Experimental Study on the Use of Microencapsulated Phase Change Material in Walls and Roofs for Energy Savings
Publication: Journal of Energy Engineering
Volume 141, Issue 4
Abstract
This paper presents an experimental investigation of a new use of phase change materials (PCM) as a coating material on concrete and hollow brick walls. Its aim is to study the influence of the integration of PCM on the thermal behaviour of cells and on the improvement of thermal comfort in buildings under the Algerian climate. Tests of the flexural strength, compressive strength, bond strength, and hardness were performed at seven days of age on composite plaster/PCM materials. Different percentages of phase change material were used in the designs of composition (plaster/PCM). In situ measurements of air and walls temperatures were made in three cells. The first one was built with traditional materials and the other two with a composite material plaster/PCM. The cells are located in the Algiers region. The measurement results show that the use of a gypsum plaster incorporating 30% PCM contributes to a reduction of the amplitude of indoor temperature of the cell by 4°C in the summer. The use of PCM has also improved thermal comfort and increased the maximum cell temperature by 2°C during winter.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support of this work (national project, PNR) provided by the Algerian Ministry of Accommodation and Town Planning and Ministry of Higher Education and Scientific Research. The authors take this opportunity to acknowledge Mr. Salim Guettala, Professor in the Civil Engineering Department, University of Djelfa, Algeria, for his comments and discussions.
References
Ahmad, M., Bontemps, A., Salle, H., and Quenard, D. (2006a). “Experimental investigation and computer simulation of thermal behavior of wallboards containing a phase change material.” Energy Build., 38(4), 357–366.
Ahmad, M., Bontemps, A., Salle, H., and Quenard, D. (2006b). “Thermal testing and numerical simulation of a prototype cell using light wallboards coupling vacuum isolation panels and phase change material.” Energy Build., 38(6), 673–681.
British Standards Institution. (2004). “Gypsum binders and gypsum plasters. Test methods.”, London.
British Standards Institution. (2005). “Gypsum binders and gypsum plasters. Definitions and requirements.”, London.
Cabeza, L. F., Castello, C., Nogue’s, M., Medrano, M., and Zubillaga, O. (2007). “Use of microencapsulated PCM in concrete walls for energy savings.” Energy Build., 39(2), 113–119.
Dehdezi, P. K., Hall, M. R., Dawson, A. D., and Casey, S. P. (2013). “Thermal, mechanical and microstructural analysis of concrete containing microencapsulated phase change materials.” Int. J. Pavement Eng., 14(5), 449–462.
Document Technique Réglementaire. (1997). “Réglementation thermique des bâtiments d’habitation. Règle de calcul des déperditionscalorifiques.”, National Center of Studies and Integrated Research on Building Engineering (CNERIB), Algeria (in French).
Document Technique Réglementaire. (2004). “Travaux d’enduits intérieurs en plâtre.”, National Center of Studies and Integrated Research on Building Engineering (CNERIB), Algeria (in French).
Entrop, A. G., Brouwers, H. J. H., and Reinders, A. H. M. E. (2011). “Experimental research on the use of micro-encapsulated phase change materials to store solar energy in concrete floors and to save energy in Dutch houses.” Solar Energy, 85(5), 1007–1020.
Feldman, D., Banu, D., Hawes, D., and Ghanbari, E. (1991). “Obtaining an energy storing building material by direct incorporation of an organic phase change material in gypsum wallboard.” Solar Energy Mater., 22(2–3), 231–242.
Hembade, L., Neithalath, N., and Rajan, S. (2014). “Understanding the energy implications of phase-change materials in concrete walls through finite-element analysis.” J. Energy Eng., 140(1), 04013009.
ISO. (1974). “Gypsum plasters. Determination of mechanical properties.”, Geneva.
Khudhair, A. M., and Farid, M. M. (2004). “A review on energy conservation in building applications with thermal storage by latent heat using phase change materials.” Energy Convers. Manage., 45(2), 263–275.
Kuznik, F., David, D., Johannes, K., and Roux, J. J. (2011). “A review on phase change materials integrated in building walls.” Renew. Sustain. Energy Rev., 15(1), 379–391.
Kuznik, F., and Virgone, J. (2009). “Experimental assessment of a phase change material for wall building use.” Appl. Energy, 86(10), 2038–2046.
Kuznik, F., Virgone, J., and Roux, J. J. (2008). “Energetic efficiency of room wall containing PCM wallboard: A full-scale experimental investigation.” Energy Build., 40(2), 148–156.
Lai, C., and Chiang, C. (2006). “How phase change materials affect thermal performance: Hollow bricks.” Build. Res. Inform., 34(2), 118–130.
Ling, T. C., and Poon, C. S. (2013). “Use of phase change materials for thermal energy storage in concrete.” Constr. Build. Mater., 46, 55–62.
Meshgin, P., Xi, Y., and Li, Y. (2012). “Utilization of phase change materials and rubber particles to improve thermal and mechanical properties of mortar.” Constr. Build. Mater., 28(1), 713–721.
Tyagi, V. V., and Buddhi, D. (2007). “PCM thermal storage in buildings: A state of art.” Renew. Sustain. Energy Rev., 11(6), 1146–1166.
Tzivanidis, C., Antonopoulos, K., and Kravvaritis, E. (2011). “Transient three-dimensional numerical solution of night ceiling cooling using PCM-embedded piping.” J. Energy Eng., 177–186.
Xiao, W., Wang, X., and Zhang, Y. (2009). “Analytical optimization of interior PCM for energy storage in a lightweight passive solar room.” Appl. Energy, 86(10), 2013–2018.
Zalba, B., Marın, J. M., Cabeza, L. F., and Mehling, H. (2003). “Review on thermal energy storage with phase change: Materials, heat transfer analysis and applications.” Appl. Thermal Eng., 23(3), 251–283.
Zeng, R., Wang, X., Di, H., Jiang, F., and Zhang, Y. (2011). “New concepts and approach for developing energy efficient buildings: Ideal specific heat for building internal thermal mass.” Energy Build., 43(5), 1081–1090.
Zhang, Z., Shi, G., Wang, S., Fang, X., Liu, X. (2013). “Thermal energy storage cement mortar containing n-octadecane/expanded graphite composite phase change material.” Renew. Energy, 50, 670–675.
Zhou, G., Zhang, Y., Wang, X., Lin, K., and Xiao, W. (2007a). “An assessment of mixed type PCM-gypsum and shape-stabilized PCM plates in a building for passive solar heating.” Solar Energy, 81(11), 1351–1360.
Zhou, G., Zhang, Y., Zhang, Q., Lin, K., and Di, H. (2007b). “Performance of a hybrid heating system with thermal storage using shape-stabilized phase change material plates.” Appl. Energy, 84(10), 1068–1077.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Feb 4, 2014
Accepted: Aug 11, 2014
Published online: Oct 6, 2014
Discussion open until: Mar 6, 2015
Published in print: Dec 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.