Experimental Analysis of Diesel-Ignited Methane Dual-Fuel Low-Temperature Combustion in a Single-Cylinder Diesel Engine
Publication: Journal of Energy Engineering
Volume 141, Issue 2
Abstract
This paper focuses on the effect of diesel injection timing, intake boost pressure, and diesel injection pressure on diesel-methane dual-fuel combustion performed in a single-cylinder research engine. The engine was operated at a constant speed of 1,500 revolutions per minute (rpm) while percentage of methane energy substitution (PES) and load were maintained at 80% and 5.1 bar net indicated mean effective pressure (IMEP), respectively. The start of injection (SOI) of diesel was varied from 250 crank angle degrees (CAD) to 350 CAD while keeping the injection pressure at 500 bar and intake boost pressure at 1.5 bar. Advancing SOI from 330° to 300° reduced indicated specific NOx (ISNOx) emissions from to less than ; further advancement of SOI did not yield any significant ISNOx reduction. Net indicated fuel conversion efficiency (IFCE) increases from 29.4% at 350 CAD SOI to 40.5% at 300 CAD SOI. Combustion efficiency trends are consistent with unburned hydrocarbon (HC) and carbon monoxide (CO) emission trends. Moreover, smoke emissions were lower than 0.1 filter smoke number (FSN) for all SOIs. A diesel injection pressure sweep from 200 to 1,300 bar at 300 CAD SOI showed that very low injection pressures lead to apparently more heterogeneous combustion and higher ISNOx, indicated specific CO (ISCO), and indicated specific HC (ISHC) emissions, whereas smoke, IFCE, and combustion efficiency remained unaffected. An injection pressure of approximately 500 bar appeared to be optimal for early SOIs. Finally, an intake boost pressure sweep from 1.1 to 1.8 bar at 300 CAD SOI and 500 bar injection pressure showed that ISNOx and smoke remained fairly low at all conditions (; ); however, increasing boost pressure resulted in an increase in both ISHC and ISCO emissions while combustion efficiency and IFCE were reduced.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support from the Sustainable Energy Research Center (US DOE Award # DE-FG36-06GO86025) and the facilities support from the Center for Advanced Vehicular Systems at Mississippi State University.
References
Abd Alla, G. H., Soliman, H. A., Badr, O. A., and Abd Rabbo, M. F. (2000). “Effect of pilot fuel quantity on the performance of a dual fuel engine.” Energy Convers. Manage., 41(6), 559–572.
Abd Alla, G. H., Soliman, H. A., Badr, O. A., and Abd Rabbo, M. F. (2002). “Effect of injection timing on the performance of a dual fuel engine.” Energy Convers. Manage., 43(2), 269–277.
Agarwal, A. K. (2007). “Biofuels (alcohols and biodiesel) applications as fuels for internal combustion engines.” Prog. Energy Combust. Sci., 33(3), 233–271.
Badr, O., Karim, G. A., and Liu, B. (1999). “An examination of the flame spread limits in a dual fuel engine.” Appl. Therm. Eng., 19(10), 1071–1080.
Beck, N. J., Barkhimer, R. L., Johnson, W. P., Wong, H. C., and Gebert, K. (1997). “Evolution of heavy duty natural gas engines—Stoichiometric, carbureted and spark ignited to lean burn, fuel injected and micro-pilot.” SAE Technical Paper 972665.
Bedoya, I. D., Arrieta, A. A., and Cadavid, F. J. (2009). “Effects of mixing system and pilot fuel quality on diesel–biogas dual fuel engine performance.” Bioresour. Technol., 100(24), 6624–6629.
Brunt, M., Rai, H., and Emtage, A. (1998). “The calculation of heat release energy from engine cylinder pressure data.” SAE Technical Paper 981052.
Carlucci, A. P., De Risi, A., Laforgia, D., and Naccarato, F. (2008). “Experimental investigation and combustion analysis of a direct injection dual-fuel diesel–natural gas engine.” Energy, 33(2), 256–263.
Chen, Z., Yao, M., Zheng, Z., and Zhang, Q. (2009). “Experimental and numerical study of methanol/dimethyl ether dual-fuel compound combustion.” Energy Fuels, 23(5), 2719–2730.
Contino, F., Dagaut, P., Dayma, G., Halter, F., Foucher, F., and Mounaïm-Rousselle, C. (2013). “Combustion and emissions characteristics of valeric biofuels in a compression ignition engine.” J. Energy Eng., A4014013.
Daisho, Y., et al. (1995). “Combustion and exhaust emissions in a direct-injection diesel engine dual-fueled with natural gas.” SAE Technical Paper 950465.
Debnath, B. K., Bora, B. J., Sahoo, N., and Saha, U. K. (2013). “Influence of emulsified palm biodiesel as pilot fuel in a biogas run dual fuel diesel engine.” J. Energy Eng., A4014005.
Dec, J. E. (1997). “A conceptual model of DI diesel combustion based on laser-sheet imaging.” SAE Trans., 106(3), 1319–1348.
Dec, J. E. (2009). “Advanced compression-ignition engines—Understanding the in-cylinder processes.” Proc. Combust. Inst., 32(2), 2727–2742.
DieselNet. (2014). “US EPA heavy-duty engine emissions standards.” 〈http://www.dieselnet.com/standards/us/hd.php〉 (Apr. 10, 2014).
Giakoumis, E. G., Rakopoulos, C. D., and Rakopoulos, D. C. (2013). “Assessment of NOx emissions during transient diesel engine operation with biodiesel blends.” J. Energy Eng., A4014004.
Gibson, C. M., Polk, A. C., Shoemaker, N. T., Srinivasan, K. K., and Krishnan, S. R. (2011). “Comparison of propane and methane performance and emissions in a turbocharged direct injection dual fuel engine.” J. Eng. Gas Turbines Power, 133(9), 092806.
Glassman, I., and Yetter, R. A. (2008). Combustion, 4th Ed., Academic Press, Waltham, MA.
Goldsworthy, L. (2012). “Combustion behavior of a heavy duty common rail marine diesel engine fumigated with propane.” Exp. Therm. Fluid Sci., 42, 93–106.
Hanson, R. M., Kokjohn, S. L., Splitter, D. A., and Reitz, R. D. (2010). “An experimental investigation of fuel reactivity controlled PCCI combustion in a heavy-duty engine.” SAE Int. J. Engines, 3(1), 700–716.
Heywood, J. B. (1988). Internal combustion engine fundamentals, McGraw-Hill, New York.
Huestis, E., Erickson, P. A., and Musculus, M. P. (2007). “In-cylinder and exhaust soot in low-temperature combustion using a wide-range of EGR in a heavy-duty diesel engine.” SAE Technical Paper 2007-01-4017.
Jindal, S., Nandwana, B. P., Rathore, N. S., and Vashistha, V. (2010). “Experimental investigation of the effect of compression ratio and injection pressure in a direct injection diesel engine running on Jatropha methyl ester.” Appl. Therm. Eng., 30(5), 442–448.
Karim, G. A. (2003). “Combustion in gas fueled compression ignition engines of the dual fuel type.” J. Eng. Gas Turbines Power, 125(3), 827–836.
Kokjohn, S. L., Hanson, R. M., Splitter, D. A., and Reitz, R. D. (2011). “Fuel reactivity controlled compression ignition (RCCI): A pathway to controlled high-efficiency clean combustion.” Int. J. Engine Res., 12(3), 209–226.
Krishnan, S. R., et al. (2004). “Strategies for reduced NOx emissions in pilot-ignited natural gas engines.” J. Eng. Gas Turbines Power, 126(3), 665–671.
Krishnan, S. R., Biruduganti, M., Mo, Y., Bell, S. R., and Midkiff, K. C. (2002). “Performance and heat release analysis of a pilot-ignited natural gas engine.” Int. J. Engine Res., 3(3), 171–184.
Kusaka, J., Okamoto, T., Daisho, Y., Kihara, R., and Saito, T. (2000). “Combustion and exhaust gas emission characteristics of a diesel engine dual-fueled with natural gas.” JSAE Rev., 21(4), 489–496.
Lee, D., Jho, Y., and Lee, C. S. (2013). “Effect of soybean and canola oil-based biodiesel blends on spray, combustion and emission characteristics in a diesel engine.” J. Energy Eng., A4014012.
Liu, Z., and Karim, G. A. (1995). “The ignition delay period in dual fuel engines.” SAE Technical Paper 950466.
McTaggart-Cowan, G., Bushe, W. K., Hill, P. G., and Munshi, S. R. (2004). “NOx reduction from a heavy-duty diesel engine with direct injection of natural gas and cooled exhaust gas recirculation.” Int. J. Engine Res., 5(2), 175–191.
McTaggart-Cowan, G. P., Reynolds, C. C. O., and Bushe, W. K. (2006). “Natural gas fuelling for heavy-duty on-road use: Current trends and future direction.” Int. J. Environ. Stud., 63(4), 421–440.
Musculus, M. P., Miles, P. C., and Pickett, L. M. (2013). “Conceptual models for partially premixed low-temperature diesel combustion.” Prog. Energy Combust. Sci., 39(2), 246–283.
Papagiannakis, R. G., and Hountalas, D. T. (2003). “Experimental investigation concerning the effect of natural gas percentage on performance and emissions of a DI dual fuel diesel engine.” Appl. Therm. Eng., 23(3), 353–365.
Papagiannakis, R. G., and Hountalas, D. T. (2004). “Combustion and exhaust emission characteristics of a dual fuel compression ignition engine operated with pilot diesel fuel and natural gas.” Energy Convers. Manage., 45(18), 2971–2987.
Papagiannakis, R. G., Hountalas, D. T., and Rakopoulos, C. D. (2007). “Theoretical study of the effects of pilot fuel quantity and its injection timing on the performance and emissions of a dual fuel diesel engine.” Energy Convers. Manage., 48(11), 2951–2961.
Papagiannakis, R. G., Rakopoulos, C. D., Hountalas, D. T., and Rakopoulos, D. C. (2010). “Emission characteristics of high speed, dual fuel, compression ignition engine operating in a wide range of natural gas/diesel fuel proportions.” Fuel, 89(7), 1397–1406.
Polk, A. C., et al. (2014a). “Diesel-ignited propane dual fuel low temperature combustion in a heavy-duty diesel engine.” Trans. ASME J. Eng. Gas Turbines Power, 136(9), 091509.
Polk, A. C., Carpenter, C. D., Srinivasan, K. K., and Krishnan, S. R. (2014b). “An investigation of diesel-ignited propane dual fuel combustion in a heavy-duty diesel engine.” Fuel, 132, 135–148.
Polk, A. C., Gibson, C. M., Shoemaker, N. T., Srinivasan, K. K., and Krishnan, S. R. (2013). “Detailed characterization of diesel-ignited propane and methane dual-fuel combustion in a turbocharged direct-injection diesel engine.” Proc. IME Part D J. Automobile Eng., 227(9), 1255–1272.
Qi, Y., Srinivasan, K. K., Krishnan, S. R., Yang, H., and Midkiff, K. C. (2007). “Effect of hot exhaust gas recirculation on the performance and emissions of an advanced injection low pilot-ignited natural gas engine.” Int. J. Engine Res., 8(3), 289–303.
Rakopoulos, C. D., Rakopoulos, D. C., Giakoumis, E. G., and Dimaratos, A. M. (2010). “Investigation of the combustion of neat cottonseed oil or its neat bio-diesel in a HSDI diesel engine by experimental heat release and statistical analyses.” Fuel, 89(12), 3814–3826.
Rakopoulos, D. C., Rakopoulos, C. D., Giakoumis, E. G., and Dimaratos, A. M. (2013). “Studying combustion and cyclic irregularity of diethyl ether as supplement fuel in diesel engine.” Fuel, 109, 325–335.
Ryu, K. (2013a). “Effects of pilot injection timing on the combustion and emissions characteristics in a diesel engine using biodiesel–CNG dual fuel.” Appl. Energy, 111, 721–730.
Ryu, K. (2013b). “Effects of pilot injection pressure on the combustion and emissions characteristics in a diesel engine using biodiesel–CNG dual fuel.” Energy Convers. Manage., 76, 506–516.
Sayin, C. (2010). “Engine performance and exhaust gas emissions of methanol and ethanol–diesel blends.” Fuel, 89(11), 3410–3415.
Sayin, C., and Canakci, M. (2009). “Effects of injection timing on the engine performance and exhaust emissions of a dual-fuel diesel engine.” Energy Convers. Manage., 50(1), 203–213.
Sayin, C., Uslu, K., and Canakci, M. (2008). “Influence of injection timing on the exhaust emissions of a dual-fuel CI engine.” Renewable Energy, 33(6), 1314–1323.
Selim, M. Y. (2004). “Sensitivity of dual fuel engine combustion and knocking limits to gaseous fuel composition.” Energy Convers. Manage., 45(3), 411–425.
Selim, M. Y. (2005). “Effect of engine parameters and gaseous fuel type on the cyclic variability of dual fuel engines.” Fuel, 84(7), 961–971.
Shoemaker, N. T., Gibson, C. M., Polk, A. C., Krishnan, S. R., and Srinivasan, K. K. (2012). “Performance and emissions characteristics of bio-diesel (B100)-ignited methane and propane combustion in a four cylinder turbocharged compression ignition engine.” Trans. ASME J. Engi. Gas Turbines Power, 134(8), 082803.
Singh, S., Krishnan, S. R., Srinivasan, K. K., Midkiff, K. C., and Bell, S. R. (2004). “Effect of pilot injection timing, pilot quantity and intake charge conditions on performance and emissions for an advanced low-pilot-ignited natural gas engine.” Int. J. Engine Res., 5(4), 329–348.
Splitter, D., Hanson, R., Kokjohn, S., and Reitz, R. (2011). “Reactivity controlled compression ignition (RCCI) heavy-duty engine operation at mid- and high-loads with conventional and alternative fuels.” SAE Technical Paper 2011-01-0363.
Srinivasan, K. K., et al. (2006a). “The advanced injection low pilot ignited natural gas engine: A combustion analysis.” J. Eng. Gas Turbines Power, 128(1), 213–218.
Srinivasan, K. K., Krishnan, S. R., and Midkiff, K. C. (2006b). “Improving low load combustion, stability, and emissions in pilot-ignited natural gas engines.” Proc. IME Part D J. Automobile Eng., 220(2), 229–239.
Srinivasan, K. K., Krishnan, S. R., Qi, Y., Midkiff, K. C., and Yang, H. (2007). “Analysis of diesel pilot-ignited natural gas low-temperature combustion with hot exhaust gas recirculation.” Combust. Sci. Technol., 179(9), 1737–1776.
Tira, H. S., et al. (2014). “Influence of fuel properties, hydrogen, and reformate additions on diesel-biogas dual-fueled engine.” J. Energy Eng., A4014003.
Wong, H. C., Beck, N. J., and Chen, S. K. (2000). “The evolution of compression ignition natural gas engines for low emission vehicles.” Proc., 2000 Fall Technical Conf. of the ASME Internal Combustion Engine Division, Paper No. (2000-ICE-318), Peoria, IL.
Yao, M., Chen, Z., Zheng, Z., Zhang, B., and Xing, Y. (2006). “Study on the controlling strategies of homogeneous charge compression ignition combustion with fuel of dimethyl ether and methanol.” Fuel, 85(14), 2046–2056.
Zheng, M., Reader, G. T., and Hawley, J. G. (2004). “Diesel engine exhaust gas recirculation––A review on advanced and novel concepts.” Energy Convers. Manage., 45(6), 883–900.
Information & Authors
Information
Published In
Journal of Energy Engineering
Volume 141 • Issue 2 • June 2015
Copyright
© 2014 American Society of Civil Engineers.
History
Received: May 25, 2014
Accepted: Aug 1, 2014
Published online: Sep 5, 2014
Discussion open until: Feb 5, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.