Improved Delta-Q Measurement Technique for Estimating the Total and Local Leakages in Residential Buildings
Publication: Journal of Energy Engineering
Volume 137, Issue 2
Abstract
The duct leakage in forced-air distribution systems has been recognized for years as a major source of energy losses in residential buildings. Recently, a measurement technique for estimating the total air leakage from residential duct systems, called Delta-Q, has been proposed. It focuses on measuring the total supply and return air leakage flows outside at operating conditions that are required for energy loss calculations. This paper discusses the Delta-Q measurement technique and proposes improvements on its model to increase the accuracy of the total leakage estimations and to provide appropriate estimation of local leakages. Accurate estimations of the total and local leakages can help to focus the choice for both the right house and location in the duct system for performing the potential repair job. Proper information as to where the leakages are located inside the duct system can reduce the time required for the duct sealing task. This study uses detailed laboratory measurements to validate the original and improved Delta-Q technique procedure and calculations. The air duct leakage laboratory (ADLL) has two different air duct configurations and a wide range of leakage levels controlled by holes created at several locations in the ductwork. This work also includes a set of simulation results to provide an insight into the performance of Delta-Q under different conditions. The simulation and experimental studies showed that the proposed Delta-Q models can improve the accuracy of total leakage estimation and provide useful information when these leakages are located inside the duct.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers acknowledge the financial support of the National Center for Energy Management and Building Technologies (NCEMBT) through funding from the DOE under Cooperative Agreement DOEDE-FC26-03GO13072.
References
American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE). (2004). “Method of test for determining the design and seasonal efficiencies of residential thermal distribution systems.” ANSI/ASHRAE 152-2004.
ASTM. (2003). “Standard test methods for determining external air leakage of air distribution systems by fan pressurization.” E1554-03.
Cummings, J. B., Tooley, J. J., Jr., and Dunsmore, R. (1990). “Impacts of duct leakage on infiltration rates, space conditioning energy use, and peak electrical demand in Florida homes.” Proc. of ACEEE Summer Study, 1990, American Council for an Energy-Efficient Economy, Washington, DC.
Dickerhoff, D., Walker, I., and Sherman, M. (2004). “Validation and improving the Delta-Q duct leakage test.” ASHRAE Transactions, 110(2), 741–751.
Francisco, P. W., Palmiter, L., and Davis, B. (1998). “Modeling the thermal distribution efficiency of ducts: Comparisons to measured results.” Energy Build., 28, 287–297.
Francisco, P. W., Palmiter, L., and Davis, B. (2003). “Insights into improved ways to measure residential duct leakage.” ASHRAE Transactions, 109(1), 485–495.
Francisco, P. W., Palmiter, L., Kruse, E., and Davis, B. (2004). “Evaluation of two new duct leakage measurement methods in 51 homes.” ASHRAE Transactions, 110(2), 727–740.
Jump, D., Walker, I. S., and Modera, M. P. (1996). “Field measurements of efficiency and duct retrofit effectiveness in residential forced air distribution systems.” Proc. of ACEEE Summer Study, 1996, American Council for an Energy-Efficient Economy, Washington, DC, 1.147–1.157.
Moujaes, S., Nassif, N., Teeters, K., Gundavelli, R., and Selvara, D. (2007). “Duct leakage measurement in residential buildings: National center for energy management and building technologies, task 5–11.” Final Rep. NCEMBT-080215, National Center for Energy Management and Building Technologies, Alexandria, VA.
Parker, D., Fairey, P., and Gu, L. (1993). “Simulation of the effects of duct leakage and heat transfer on residential space-cooling energy use.” Energy Build., 20(2), 97–114.
Sherman, M., Walker, I., and Dickerhoff, D. (2000). “Stopping duct quacks: Longevity of residential duct sealants.” Proc. of ACEEE Summer Study, 2000, American Council for an Energy-Efficient Economy, Washington, DC.
Siegel, J., McWilliams, J., and Walker, I. S. (2003). “Comparison between predicted duct effectiveness from proposed ASHRAE Standard 152P and measured field data for residential forced air cooling systems.” ASHRAE Trans., 109(1), 503–512.
Walker, I. S., Sherman, M. H., and Dickerhoff, D. J. (2004). “Reducing uncertainty for the Delta Q duct leakage test.” LBNL Rep. 2004, 53549.
Walker, I. S., Sherman, M. H., Wempen, J., Wang, D., and Dickerhoff, D. J. (2001). “Development of a new duct leakage test.” LBNL Rep. 2001, 47308.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Nov 24, 2008
Accepted: Sep 20, 2010
Published online: Sep 22, 2010
Published in print: Jun 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.