Retracted: Elastic Guided Wave Propagation in the Prestressed Helical Multiwire Waveguide
This article has been corrected.
VIEW CORRECTIONPublication: Journal of Engineering Mechanics
Volume 148, Issue 9
Abstract
Studying ultrasonic guided wave modes in multiple steel wires helps extend and apply wave dynamics theory to practical engineering. This research focused on elastic wave propagation for investigating dispersion behavior in a helical waveguide under the prestressed state. For the guided wave theory of one-dimensional propagation, the physical system represented as a curve must satisfy translation invariance. Elastic wave propagation in a helical waveguide was analyzed using the semianalytical finite element (SAFE) method. The scaled Frenet–Serret and twisted basis dispersion curves were analyzed for comparison. The bases were used to define covariant and contravariant bases where the strain and stress tensors were expressed. Then, by proving the translational invariance of the system in the curvilinear coordinates, a Fourier transform of the displacement was deployed to distinguish plane waves based on their wavenumber and reduce the study of the waveguide according to its cross-section. Later, the SAFE method derived from the twisted cylindrical coordinate system was compared with the standard axisymmetric SAFE method. Analysis of an outer steel wire of the seven-wire helical strand was carried out for undamped and damped cases with initial prestress conditions to investigate the dispersion behavior of the helical waveguide. Static analysis of the entire seven-wire helical strand was carried out by considering an initial prestress field, and a finite-element method based on asymptotic expansion theory was used to solve contact stress field calculation. Correspondingly, the proposed method was verified with the classical Machida and Costello calculation theories for calculating the stress field on its respective axial cross-section for each wire. A very complex band diagram needs to be investigated while performing a dynamic analysis of the helical waveguide. The current work introduces the modal filters via the so-called coupling conditions to parse the complex dispersion characteristics. When the SAFE method is used to analyze its dynamic wave properties, the employed coupling condition reduces the degrees of freedom of the system and improves calculation efficiency. Henceforth, the proposed methodology for calculating the prestressed state is the potential health monitoring scheme for a helical multiwire.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The author sincerely thanks the anonymous reviewers for their valuable comments and suggestions.
References
Abbena, E., S. Salamon, and A. Gray. 2017. Modern differential geometry of curves and surfaces with Mathematica. Boca Raton, FL: CRC Press.
Achenbach, J. D. 1973. Wave propagation in elastic solids. Amsterdam, Netherlands: North-Holland.
Baltazar, A., C. D. Hernandez-Salazar, and B. Manzanares-Martinez. 2010. “Study of wave propagation in a multiwire cable to determine structural damage.” NDT & E Intl. 43 (8): 726–732. https://doi.org/10.1016/j.ndteint.2010.08.007.
Bartoli, I., A. Marzani, F. L. Di Scalea, and E. Viola. 2006. “Modeling wave propagation in damped waveguides of arbitrary cross-section.” J. Sound Vib. 295 (3–5): 685–707. https://doi.org/10.1016/j.jsv.2006.01.021.
Cartraud, P., and T. Messager. 2006. “Computational homogenization of periodic beam-like structures.” Int. J. Solids Struct. 43 (3–4): 686–696. https://doi.org/10.1016/j.ijsolstr.2005.03.063.
Chapelle, D., and K. J. Bathe. 2010. The finite element analysis of shells-fundamentals. Berlin: Springer.
Chen, Y., F. Meng, and X. Gong. 2017. “Full contact analysis of wire rope strand subjected to varying loads based on semi-analytical method.” Int. J. Solids Struct. 117 (5): 51–66. https://doi.org/10.1016/j.ijsolstr.2017.04.004.
Costello, G. A., and J. W. Phillips. 1979. “Static response of stranded wire helical springs.” Int. J. Mech. Sci. 21 (3): 171–178. https://doi.org/10.1016/0020-7403(79)90021-3.
Frikha, A., P. Cartraud, and F. Treyssede. 2013. “Mechanical modeling of helical structures accounting for translational invariance. Part 1: Static behavior.” Int. J. Solids Struct. 50 (9): 1373–1382. https://doi.org/10.1016/j.ijsolstr.2013.01.010.
Frikha, A., F. Treyssède, and P. Cartraud. 2011. “Effect of axial load on the propagation of elastic waves in helical beams.” Wave Motion 48 (1): 83–92. https://doi.org/10.1016/j.wavemoti.2010.08.001.
Gavrić, L. 1995. “Computation of propagative waves in free rail using a finite element technique.” J. Sound Vib. 185 (3): 531–543. https://doi.org/10.1006/jsvi.1995.0398.
Hayashi, T., W. J. Song, and J. L. Rose. 2003. “Guided wave dispersion curves for a bar with an arbitrary cross-section, a rod and rail example.” Ultrasonics 41 (3): 175–183. https://doi.org/10.1016/S0041-624X(03)00097-0.
Hayashi, T., C. Tamayama, and M. Murase. 2006. “Wave structure analysis of guided waves in a bar with an arbitrary cross-section.” Ultrasonics 44 (1): 17–24. https://doi.org/10.1016/j.ultras.2005.06.006.
Jiang, W. G., and J. L. Henshall. 2000. “A novel finite element model for helical springs.” Finite Elem. Anal. Des. 35 (4): 363–377. https://doi.org/10.1016/S0168-874X(99)00076-1.
Jiang, W. G., M. K. Warby, and J. L. Henshall. 2008. “Statically indeterminate contacts in axially loaded wire strand.” Eur. J. Mech.-A/Solids 27 (1): 69–78. https://doi.org/10.1016/j.euromechsol.2007.02.003.
Kolpakov, A. G. 1991. “Calculation of the characteristics of thin elastic rods with a periodic structure.” J. Appl. Math. Mech. 55 (3): 358–365. https://doi.org/10.1016/0021-8928(91)90039-W.
Kumar, K. V., T. J. Saravanan, R. Sreekala, N. Gopalakrishnan, and K. M. Mini. 2017. “Structural damage detection through longitudinal wave propagation using spectral finite element method.” Geomech. Eng. 12 (1): 161–183. https://doi.org/10.12989/gae.2017.12.1.161.
Kwun, H., K. A. Bartels, and J. J. Hanley. 1998. “Effects of tensile loading on the properties of elastic-wave propagation in a strand.” J. Acoust. Soc. Am. 103 (6): 3370–3375. https://doi.org/10.1121/1.423051.
Lanza di Scalea, F., P. Rizzo, and F. Seible. 2003. “Stress measurement and defect detection in steel strands by guided stress waves.” J. Mater. Civ. Eng. 15 (3): 219–227. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:3(219).
Li, C., Q. Han, Y. Liu, X. Liu, and B. Wu. 2015. “Investigation of wave propagation in double cylindrical rods considering the effect of prestress.” J. Sound Vib. 353 (May): 164–180. https://doi.org/10.1016/j.jsv.2015.05.017.
Li, C. L., Q. Han, and Y. J. Liu. 2017. “Simplified elastic wave modeling in seven-wire prestressed parallel strands.” Acta Mech. 228 (9): 3251–3263. https://doi.org/10.1007/s00707-017-1860-1.
Liu, X., B. Wu, F. Qin, C. He, and Q. Han. 2017. “Observation of ultrasonic guided wave propagation behaviours in prestressed multi-wire structures.” Ultrasonics 73 (8): 196–205. https://doi.org/10.1016/j.ultras.2016.08.014.
Loveday, P. W. 2009. “Semi-analytical finite element analysis of elastic waveguides subjected to axial loads.” Ultrasonics 49 (3): 298–300. https://doi.org/10.1016/j.ultras.2008.10.018.
Machida, S., and A. J. Durelli. 1973. “Response of a strand to axial and torsional displacements.” J. Mech. Eng. Sci. 15 (4): 241–251. https://doi.org/10.1243/JMES_JOUR_1973_015_045_02.
Marzani, A. 2008. “Time–transient response for ultrasonic guided waves propagating in damped cylinders.” Int. J. Solids Struct. 45 (25–26): 6347–6368. https://doi.org/10.1016/j.ijsolstr.2008.07.028.
Mazzotti, M., A. Marzani, I. Bartoli, and E. Viola. 2012. “Guided waves dispersion analysis for prestressed viscoelastic waveguides by means of the SAFE method.” Int. J. Solids Struct. 49 (18): 2359–2372. https://doi.org/10.1016/j.ijsolstr.2012.04.041.
Meng, F., Y. Chen, M. Du, and X. Gong. 2016. “Study on effect of inter-wire contact on mechanical performance of wire rope strand based on semi-analytical method.” Int. J. Mech. Sci. 115–116 (7): 416–427. https://doi.org/10.1016/j.ijmecsci.2016.07.012.
Nair, A., and C. S. Cai. 2010. “Acoustic emission monitoring of bridges: Review and case studies.” Eng. Struct. 32 (6): 1704–1714. https://doi.org/10.1016/j.engstruct.2010.02.020.
Nelson, R. B., S. B. Dong, and R. D. Kalra. 1971. “Vibrations and waves in laminated orthotropic circular cylinders.” J. Sound Vib. 18 (3): 429–444. https://doi.org/10.1016/0022-460X(71)90714-0.
Onipede, O., and S. B. Dong. 1996. “Propagating waves and end modes in pre-twisted beams.” J. Sound Vib. 195 (2): 313–330. https://doi.org/10.1006/jsvi.1996.0424.
Pavlakovic, B. N., M. J. S. Lowe, and P. Cawley. 2001. “High-frequency low-loss ultrasonic modes in imbedded bars.” J. App. Mech. 68 (1): 67–75. https://doi.org/10.1115/1.1347995.
Rizzo, P. 2006. “Ultrasonic wave propagation in progressively loaded multi-wire strands.” Exp. Mech. 46 (3): 297–306. https://doi.org/10.1007/s11340-006-7248-0.
Saravanan, T. J. 2021a. “Elastic wave methods for non-destructive damage diagnosis in the axisymmetric viscoelastic cylindrical waveguide.” Measurement 177 (Jan): 109253. https://doi.org/10.1016/j.measurement.2021.109253.
Saravanan, T. J. 2021b. “Guided ultrasonic wave-based investigation on the transient response in an axisymmetric viscoelastic cylindrical waveguide.” Ultrasonics 117 (12): 106543. https://doi.org/10.1016/j.ultras.2021.106543.
Saravanan, T. J. 2021c. “Investigation on elastic guided wave propagation in a parallel axisymmetric stressed viscoelastic cylindrical waveguide.” Mech. Adv. Mat. Struct. 2021 (Jan): 1–23. https://doi.org/10.1080/15376494.
Saravanan, T. J. 2022a. “Convergence study on ultrasonic guided wave propagation modes in an axisymmetric cylindrical waveguide.” Mech. Adv. Mat. Struct. 29 (13): 1856–1873. https://doi.org/10.1080/15376494.2020.1842949.
Saravanan, T. J. 2022b. “Investigation of guided wave dispersion characteristics for fundamental modes in an axisymmetric cylindrical waveguide using rooting strategy approach.” Mech. Adv. Mat. Struct. 29 (4): 495–505. https://doi.org/10.1080/15376494.2020.1777601.
Saravanan, T. J., N. Gopalakrishnan, and N. P. Rao. 2015. “Damage detection in structural element through propagating waves using radially weighted and factored RMS.” Measurement 73 (6): 520–538. https://doi.org/10.1016/j.measurement.2015.06.015.
Saravanan, T. J., N. Gopalakrishnan, and N. P. Rao. 2017. “Detection of damage through coupled axial–flexural wave interactions in a sagged rod using the spectral finite element method.” J. Vib. Control 23 (20): 3345–3364. https://doi.org/10.1177/1077546316630855.
Saravanan, T. J., N. Gopalakrishnan, and N. P. Rao. 2018. “Experiments on coupled axial–flexural wave propagation in a sagged rod with structural discontinuity using piezoelectric transducers.” J. Vib. Control 24 (13): 2717–2731. https://doi.org/10.1177/1077546317693431.
Taweel, H., S. B. Dong, and M. Kazic. 2000. “Wave reflection from the free end of a cylinder with an arbitrary cross-section.” Int. J. Solids Struct. 37 (12): 1701–1726. https://doi.org/10.1016/S0020-7683(98)00301-1.
Thiyagarajan, J. S. 2020. “Non-destructive testing mechanism for prestressed steel wire using acoustic emission monitoring.” Materials (Basel) 13 (21): 5029. https://doi.org/10.3390/ma13215029.
Treyssède, F. 2008. “Elastic waves in helical waveguides.” Wave Motion 45 (4): 457–470. https://doi.org/10.1016/j.wavemoti.2007.09.004.
Treyssède, F. 2016. “Dispersion curve veering of longitudinal guided waves propagating inside prestressed seven-wire strands.” J. Sound Vib. 367 (Dec): 56–68. https://doi.org/10.1016/j.jsv.2015.12.050.
Treyssède, F. 2019. “Free and forced response of three-dimensional waveguides with rotationally symmetric cross-sections.” Wave Motion 87 (8): 75–91. https://doi.org/10.1016/j.wavemoti.2018.08.001.
Treyssède, F., A. Frikha, and P. Cartraud. 2013. “Mechanical modeling of helical structures accounting for translational invariance. Part 2: Guided wave propagation under axial loads.” Int. J. Solids Struct. 50 (9): 1383–1393. https://doi.org/10.1016/j.ijsolstr.2013.01.006.
Treyssède, F., and L. Laguerre. 2010. “Investigation of elastic modes propagating in multi-wire helical waveguides.” J. Sound Vib. 329 (10): 1702–1716. https://doi.org/10.1016/j.jsv.2009.11.021.
Treyssède, F., L. Laguerre, P. Cartraud, and T. Soulard. 2021. “Elastic guided waves in helical multi-wire armors.” Ultrasonics 110 (2): 106294. https://doi.org/10.1016/j.ultras.2020.106294.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Aug 17, 2021
Accepted: Apr 11, 2022
Published online: Jun 17, 2022
Published in print: Sep 1, 2022
Discussion open until: Nov 17, 2022
ASCE Technical Topics:
- Analysis (by type)
- Business management
- Continuum mechanics
- Curvature
- Dynamic analysis
- Dynamics (solid mechanics)
- Elastic analysis
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Finite element method
- Geometry
- Materials engineering
- Materials processing
- Mathematics
- Metals (material)
- Methodology (by type)
- Numerical methods
- Practice and Profession
- Prestressing
- Public administration
- Public health and safety
- Safety
- Solid mechanics
- Steel
- Structural analysis
- Structural engineering
- Wave propagation
- Waves (mechanics)
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.