Coupled Experimental and Computational Investigation of the Interplay between Discrete and Continuous Reinforcement in Ultrahigh Performance Concrete Beams. I: Experimental Testing
Publication: Journal of Engineering Mechanics
Volume 147, Issue 9
Abstract
Ultrahigh performance concrete (UHPC) is a special class of cementitious composites with superior strength and durability characteristics. Typically, UHPC contains very fine aggregate (size less than 1 mm) and short fiber reinforcement (less than 15 mm long). This sets it apart from the family of regular fiber-reinforced concrete (FRC) that has aggregate and fiber of similar lengths since the aggregate is typically coarse (10–20 mm) and that makes fiber effects on heterogeneity and crack bridging in UHPC more dominant compared to FRC. Additionally, since fiber content is relatively high (around 2% by volume), it is expected that a significant interplay exists between fiber content and traditional continuous reinforcement (rebars). Such interplay could affect the modes of failure, load-carrying capacity, and ductility of reinforced-UHPC (R-UHPC) members. Given such differences, prediction of failure mechanisms for R-UHPC members via extrapolation of design guides available for normal concrete (NC) and FRC could be debatable. Therefore, this two-part study discusses a coupled experimental and computational investigation analyzing the effect of fiber-rebar interplay on the modes of failure, strength, and ductility of R-UHPC prismatic members. The experiments included an initial campaign of testing 12 R-UHPC beams with different fiber contents and reinforcement ratios. Beams were tested with an eccentric three-point bending setup along with material level companion tests on specimens cast from same batches. Interestingly, all beams with fiber failed in bending without noticeable shear failures. The data from this initial campaign were used to calibrate and validate a computational modeling framework. This validated model was further used to predict the needed dimensions to achieve shear failure. Given these dimensions, a second experimental campaign was performed, and all tested beams failed in shear as predicted. These experimental programs are reported in the present Part I. The computational counterpart is described in the companion paper as Part II.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All experimental data presented in this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to acknowledge the financial support from the Egyptian Ministry of Higher Education for the first author to perform the experimental campaign. The authors also acknowledge the generous donation of all UHPC materials by Ductal.
References
ACI (American Concrete Institute). 2008. Building code requirements for structural concrete (ACI 318-08) and commentary—An ACI standard. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete (ACI 318-14) and commentary—An ACI standard. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2019. Building code requirements for structural concrete (ACI 318-19) and commentary—An ACI standard. Farmington Hills, MI: ACI.
AFGC-Sétra (Association Française de Génie Civil-Service d'études Techniques Des Routes Et Autoroutes). 2002. Ultra-high performance fiber-reinforced concrete-interim recommendations. Bagneux, France: AFGC-Sétra.
AFGC-Sétra (Association Française de Génie Civil-Service d'études Techniques Des Routes Et Autoroutes). 2013. Ultra-high performance fiber-reinforced concrete-recommendations. Bagneux, France: AFGC-Sétra.
Alford, N. M., G. Groves, and D. Double. 1982. “Physical properties of high strength cement pastes.” Cem. Concr. Res. 12 (3): 349–358. https://doi.org/10.1016/0008-8846(82)90083-7.
ASTM. 2014. Standard test methods and definitions for mechanical testing of steel products. ASTM A370-14. West Conshohocken, PA: ASTM.
Baby, F., P. Marchand, and F. Toutlemonde. 2014a. “Shear behavior of ultrahigh performance fiber-reinforced concrete beams. I: Experimental investigation.” J. Struct. Eng. 140 (5): 04013111. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000907.
Baby, F., P. Marchand, and F. Toutlemonde. 2014b. “Shear behavior of ultrahigh performance fiber-reinforced concrete beams. II: Analysis and design provisions.” J. Struct. Eng. 140 (5): 04013112. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000908.
Bache, H. H. 1981. Densified cement/ultra-fine particle-based materials. Aalborg, Denmark: Aalborg Portland.
Bahij, S., S. K. Adekunle, M. Al-Osta, S. Ahmad, S. U. Al-Dulaijan, and M. K. Rahman. 2018. “Numerical investigation of the shear behavior of reinforced ultra-high-performance concrete beams.” Struct. Concr. 2018 (19): 305–317. https://doi.org/10.1002/suco.201700062.
Chen, L., and B. A. Graybeal. 2012. “Modeling structural performance of ultrahigh performance concrete I-girders.” J. Bridge Eng. 17 (5): 754–764. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000305.
Chen, S., R. Zhang, L.-J. Jia, and J.-Y. Wang. 2018. “Flexural behaviour of rebar-reinforced ultra-high-performance concrete beams.” Mag. Concr. Res. 70 (19): 997–1015. https://doi.org/10.1680/jmacr.17.00283.
de Larrard, F., and T. Sedran. 1994. “Optimization of ultra-high-performance concrete by the use of a packing model.” Cem. Concr. Res. 24 (6): 997–1009. https://doi.org/10.1016/0008-8846(94)90022-1.
Dupont, D. 2003. “Modelling and experimental validation of the constitutive law () and cracking behaviour of steel fibre reinforced concrete.” Ph.D. thesis, Dept. of Civil Engineering, Catholic Univ. of Leuven.
Duque, L. F. M., I. Varga, and B. A. Graybeal. 2016. “Fiber reinforcement influence on the tensile response of UHPFRC.” In Proc., 1st Int. Interactive Symp. on UHPC-2016, 1–10. Des Moines, IA: Iowa State University Digital Press. https://doi.org/10.21838/uhpc.2016.86.
Graybeal, B. A. 2006. Material property characterization of ultra-high performance concrete. Washington, DC: Federal Highway Administration, DOT.
Graybeal, B. A. 2011. Ultra-high performance concrete. Washington, DC: Federal Highway Administration, DOT.
Haber, Z. B., I. D. La Varga, B. A. Graybeal, B. Nakashoji, and R. El-Helou. 2018. Ultra-high performance concrete. Washington, DC: Federal Highway Administration, DOT.
Hasgul, U., K. Turker, and T. Birol. 2018. “Flexural behavior of ultra-high-performance fiber reinforced concrete beams with low and high reinforcement ratios.” Struct. Concr. 19 (6): 1577–1590. https://doi.org/10.1002/suco.201700089.
McSwain, A. C., K. A. Berube, G. Cusatis, and E. N. Landis. 2018. “Confinement effects on fiber pullout forces for ultra-high-performance concrete.” Cem. Concr. Compos. 91 (Aug): 53–58. https://doi.org/10.1016/j.cemconcomp.2018.04.011.
Mészöly, T., and N. Randl. 2018. “Shear behavior of fiber-reinforced ultra-high performance concrete beams.” Eng. Struct. 168 (Aug): 119–127. https://doi.org/10.1016/j.engstruct.2018.04.075.
Mobasher, B., Y. Yao, and C. Soranakom. 2015. “Analytical solutions for flexural design of hybrid steel fiber reinforced concrete beams.” Eng. Struct. 100 (Oct): 164–177. https://doi.org/10.1016/j.engstruct.2015.06.006.
Pourbaba, M., A. Joghataie, and A. Mirmiran. 2018. “Shear behavior of ultra-high performance concrete.” Constr. Build. Mater. 183 (Sep): 554–564. https://doi.org/10.1016/j.conbuildmat.2018.06.117.
Qi, J., Z. J. Ma, and J. Wang. 2017. “Shear strength of UHPFRC beams: Mesoscale fiber-matrix discrete model.” J. Struct. Eng. 143 (4): 04016209. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001701.
Rossi, P., D. Daviau-Desnoyers, and J.-L. Tailhan. 2018. “Probabilistic numerical model of cracking in ultra-high performance fibre reinforced concrete (UHPFRC) beams subjected to shear loading.” Cem. Concr. Compos. 90 (Jul): 119–125. https://doi.org/10.1016/j.cemconcomp.2018.03.019.
Schmidt, M., and E. Fehling. 2005. “Ultra-high-performance concrete: Research, development and application in Europe.” ACI Spec. Publ. 228 (1): 51–78.
Shao, Y., and S. L. Billington. 2019. “Predicting the two predominant flexural failure paths of longitudinally reinforced high-performance fiber-reinforced cementitious composite structural members.” Eng. Struct. 199 (Nov): 109581. https://doi.org/10.1016/j.engstruct.2019.109581.
Singh, M., A. Sheikh, M. Mohamed Ali, P. Visintin, and M. Griffith. 2017. “Experimental and numerical study of the flexural behaviour of ultra-high performance fibre reinforced concrete beams.” Constr. Build. Mater. 138 (May): 12–25. https://doi.org/10.1016/j.conbuildmat.2017.02.002.
Sorelli, L., G. Constantinides, F.-J. Ulm, and F. Toutlemonde. 2008. “The nano-mechanical signature of ultra high performance concrete by statistical nanoindentation techniques.” Cem. Concr. Res. 38 (12): 1447–1456. https://doi.org/10.1016/j.cemconres.2008.09.002.
Stürwald, S. 2018. “Bending behaviour of UHPC reinforced with rebars and steel fibres.” In High tech concrete: Where technology and engineering meet, 473–481. New York: Springer.
Vandewalle, L., et al. 2003. “RILEM TC 162-TDF: Test and design methods for steel fibre reinforced concrete’-sigma-epsilon-design method—Final recommendation.” Mater. Struct. 36 (262): 560–567.
Voo, Y. L., W. K. Poon, and S. J. Foster. 2010. “Shear strength of steel fiber-reinforced ultrahigh-performance concrete beams without stirrups.” J. Struct. Eng. 136 (11): 1393–1400. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000234.
Wahba, K., H. Marzouk, and N. Dawood. 2012. “Structural behavior of UHPFRC beams without stirrups.” In Proc., 3rd Int. Structural Specialty Conf., 1–10. Montréal: Canadian Society of Civil Engineers.
Wang, D., C. Shi, Z. Wu, J. Xiao, Z. Huang, and Z. Fang. 2015. “A review on ultra high performance concrete. Part II: Hydration, microstructure and properties.” Constr. Build. Mater. 96 (Oct): 368–377. https://doi.org/10.1016/j.conbuildmat.2015.08.095.
Yang, I. H., C. Joh, and B.-S. Kim. 2010. “Structural behavior of ultra high performance concrete beams subjected to bending.” Eng. Struct. 32 (11): 3478–3487. https://doi.org/10.1016/j.engstruct.2010.07.017.
Yavas, A., and C. O. Goker. 2020. “Impact of reinforcement ratio on shear behavior of i-shaped UHPC beams with and without fiber shear reinforcement.” Materials (Basel) 13 (7): 1525. https://doi.org/10.3390/ma13071525.
Yin, H., K. Shirai, and W. Teo. 2019. “Finite element modelling to predict the flexural behaviour of ultra-high performance concrete members.” Eng. Struct. 183 (Mar): 741–755. https://doi.org/10.1016/j.engstruct.2019.01.046.
Yoo, D.-Y., N. Banthia, and Y.-S. Yoon. 2017. “Experimental and numerical study on flexural behavior of ultra-high-performance fiber-reinforced concrete beams with low reinforcement ratios.” Can. J. Civ. Eng. 44 (1): 18–28. https://doi.org/10.1139/cjce-2015-0384.
Yousef, A. M., A. M. Tahwia, and N. A. Marami. 2018. “Minimum shear reinforcement for ultra-high performance fiber reinforced concrete deep beams.” Constr. Build. Mater. 184 (Sep): 177–185. https://doi.org/10.1016/j.conbuildmat.2018.06.022.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Oct 23, 2020
Accepted: Feb 24, 2021
Published online: Jun 25, 2021
Published in print: Sep 1, 2021
Discussion open until: Nov 25, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.