Optimal Design of Triangular Arches against Buckling
Publication: Journal of Engineering Mechanics
Volume 146, Issue 7
Abstract
This paper is concerned with the optimal design of triangular arches of a given volume of material for maximum buckling capacity. The buckling criteria of triangular arches are derived analytically by using stability functions. Optimal designs of triangular arches with various vertical load positions, base support conditions, and apical joint conditions are obtained based on an optimization procedure involving two decision variables (arch height and cross-sectional area ratio ). Based on the optimization results, design recommendations for triangular arches against buckling are (1) the optimal height for triangular arches be taken as where is the span length of the arch, and (2) both members of the triangular arch are to take on the same cross-sectional area (i.e., ) when the arch has a rigid joint at the apical point, whereas the cross-sectional area ratio should be determined based on the optimality condition that both members should buckle at the same time when the arch has a hinge joint. By changing the base support condition from pinned-pinned to fixed-fixed, the maximum buckling load of the optimal triangular arches is increased by about 2.05 times.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
References
Bažant, Z. P., and L. Cedolin. 2010. Stability of structures: Elastic, inelastic, fracture and damage theories. Singapore: World Scientific.
Błachut, J., and A. Gajewski. 1981. “On unimodal and bimodal optimal design of funicular arches.” Int. J. Solids Struct. 17 (7): 653–667. https://doi.org/10.1016/0020-7683(81)90002-0.
Bochenek, B. 1988. “On multimodal parametrical optimization of arches against plane and spatial buckling.” Eng. Optim. 14 (1): 27–37. https://doi.org/10.1080/03052158808941197.
Bochenek, B., and M. Yczkowski. 1990. “Optimal I-section of an elastic arch under stability constraints.” Eng. Optim. 16 (2): 137–148. https://doi.org/10.1080/03052159008941169.
Budiansky, B., J. C. Frauenthal, and J. W. Hutchinson. 1969. “On optimal arches.” J. Appl. Mech. 36 (4): 880–882. https://doi.org/10.1115/1.3564790.
Ekhande, S. G., M. Selvappalam, and M. K. S. Madugula. 1989. “Stability functions for three-dimensional beam-columns.” J. Struct. Eng. 115 (2): 467–479. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:2(467).
Gajewski, A., and M. Zyczkowski. 2012. Vol. 13 of Optimal structural design under stability constraints. Dordrecht, Netherlands: Kluwer.
Horne, M. R., and W. Merchant. 1965. The stability of frames, 99. Oxford, UK: Pergamon.
Munoz, H. R. 1991. “Elastic second-order computer analysis of beam–columns and frames.” M.S. thesis, Univ. of Texas at Austin.
Na, T. Y., and G. M. Kurajian. 1977. “On optimal arch design.” J. Eng. Ind. 99 (1): 37–40. https://doi.org/10.1115/1.3439161.
Nelder, J. A., and R. Mead. 1965. “A simplex method for function minimization.” Comput. J. 7 (4): 308–313. https://doi.org/10.1093/comjnl/7.4.308.
Pan, W. H., M. R. Eatherton, X. Nie, and J. S. Fan. 2018. “Stability and adequate bracing design of pre-tensioned cable braced inverted-Y-shaped Ferris wheel support system using matrix structural second-order analysis approach.” J. Struct. Eng. 144 (10): 04018194. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002185.
Pan, W. H., M. R. Eatherton, M. X. Tao, Y. Yang, and X. Nie. 2017. “Design of single-level guyed towers considering interrelationship between bracing strength and rigidity requirements.” J. Struct. Eng. 143 (9): 04017128. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001857.
Pan, W. H., J. J. Wang, X. Nie, and J. Z. Tong. 2019. “Adequately rigid cross-beam for bridge tower designs.” J. Bridge Eng. 24 (12): 04019120. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001500.
Rozvany, G. I. N., C. M. Wang, and M. Dow. 1982. “Prager-structures: Archgrids and cable networks of optimal layout.” Comput. Methods Appl. Mech. Eng. 31 (1): 91–113. https://doi.org/10.1016/0045-7825(82)90049-4.
Tadjbakhsh, I., and M. Farshad. 1975. “On conservatively loaded funicular arches and their optimal design.” In Optimization in structural design, 215–228. Berlin: Springer.
Wu, C. H. 1968. “The strongest circular arch—A perturbation solution.” J. Appl. Mech. 35 (3): 476–480. https://doi.org/10.1115/1.3601238.
Yuan, S. 2008. Programming structural mechanics. [In Chinese.] 2nd ed. Beijing: Higher Education Press.
Zhang, H., and C. M. Wang. 2018. “Hencky bar-chain model for optimal circular arches against buckling.” Mech. Res. Commun. 88 (Mar): 7–11. https://doi.org/10.1016/j.mechrescom.2018.01.001.
Zhou, J. S., W. H. Pan, H. Zhang, and C. M. Wang. 2019. “Modeling joints with multiple members in Hencky bar-chain model for buckling analysis of frames.” Int. J. Mech. Sci. 164 (Dec): 105165. https://doi.org/10.1016/j.ijmecsci.2019.105165.
Information & Authors
Information
Published In
Journal of Engineering Mechanics
Volume 146 • Issue 7 • July 2020
Copyright
©2020 American Society of Civil Engineers.
History
Received: Oct 14, 2019
Accepted: Jan 30, 2020
Published online: Apr 21, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 21, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.