Ovalization Restraint in Four-Point Bending Tests of Tubes
Publication: Journal of Engineering Mechanics
Volume 145, Issue 3
Abstract
Four-point bending tests have been a staple in many structural engineering experiments as a reliable way of assessing the bending resistance of circular hollow sections, tubes, and cylindrical shells, and they continue to be widely performed. However, relatively little attention appears to have been paid to quantifying the effects of different boundary conditions on the test outcome. In particular, the restraint or freedom given to the cross section at the ends of a specimen to ovalize can have a significant impact when the specimen is in an appropriate length range. Ovalization is an elastic geometrically nonlinear phenomenon that is known to reduce the elastic bending resistance by as much as half in long tubes or cylinders. This paper presents a short distillation of some recent advances in understanding the buckling of cylindrical shells under uniform bending, identifying the strong influence of cylinder length on cross-section ovalization. A sample set of three-dimensional load application arrangements used in existing four-point bending tests was simulated using finite elements, allowing an assessment of the differences caused by prebuckling ovalization and its effect on the tested bending resistance. The study is limited to elastic behavior to identify the effect of ovalization alone in reducing stiffness without material nonlinearity. The outcomes demonstrate that maintaining circularity at inner load application points by appropriate stiffening has a significant effect. With freedom to ovalize, a significant reduction in stiffness occurs, leading to much lower bending resistance at buckling than may be achievable in practical applications.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The partial sponsorship of the China Scholarship Council is gratefully acknowledged.
References
Brazier, L. G. 1927. “On the flexure of thin cylindrical shells and other ‘thin’ sections.” Proc. R. Soc. Ser. A 116 (773): 104–114. https://doi.org/10.1098/rspa.1927.0125.
Calladine, C. 1983. Theory of shell structures. Cambridge, UK: Cambridge University Press.
CEN (European Committee for Standardization). 2007. Eurocode 3, Part 1-6: Strength and stability of shell structures. EN 1993-1-6. Brussels, Belgium: CEN.
Elchalakani, M., X. Zhao, and R. Grzebieta. 2002a. “Bending tests to determine slenderness limits for cold-formed circular hollow sections.” J. Constr. Steel Res. 58 (11): 1407–1430. https://doi.org/10.1016/S0143-974X(01)00106-7.
Elchalakani, M., X. Zhao, and R. Grzebieta. 2002b. “Plastic mechanism analysis of circular tubes under pure bending.” Int. J. Mech. Sci. 44 (6): 1117–1143. https://doi.org/10.1016/S0020-7403(02)00017-6.
Elchalakani, M., X. Zhao, and R. Grzebieta. 2002c. “Plastic slenderness limits for cold-formed circular hollow sections.” Aust. J. Struct. Eng. 3 (3): 127–141. https://doi.org/10.1080/13287982.2002.11464900.
Gresnigt, A. M., and R. J. van Foeken. 2001. “Local buckling of UOE and seamless steel pipes.” In Proc., 11th Int. Offshore and Polar Engineering Conf., 131–142. Cupertino, CA: International Society of Offshore and Polar Engineers.
Guo, L., S. Yang, and H. Jiao. 2013. “Behaviour of thin-walled circular hollow section tubes subjected to bending.” Thin-Walled Struct. 73: 281–289. https://doi.org/10.1016/j.tws.2013.08.014.
Jiao, H., and X.-L. Zhao. 2004. “Section slenderness limits of very high strength circular steel tubes in bending.” Thin-Walled Struct. 42 (9): 1257–1271. https://doi.org/10.1016/j.tws.2004.03.020.
Karamanos, S. 2002. “Bending instabilities of elastic tubes.” Int. J. Solids Struct. 39 (8): 2059–2085. https://doi.org/10.1016/S0020-7683(02)00085-9.
Kiymaz, G. 2005. “Strength and stability criteria for thin-walled stainless steel circular hollow section members under bending.” Thin-Walled Struct. 43 (10): 1534–1549. https://doi.org/10.1016/j.tws.2005.06.006.
Kobayashi, T., Y. Mihara, and F. Fujii. 2012. “Path-tracing analysis for post-buckling process of elastic cylindrical shells under axial compression.” Thin-Walled Struct. 61: 180–187. https://doi.org/10.1016/j.tws.2012.05.018.
Limam, A., L. H. Lee, and S. Kyriakides. 2010. “On the collapse of dented tubes under combined bending and internal pressure.” Int. J. Mech. Sci. 55 (1): 1–12. https://doi.org/10.1016/j.ijmecsci.2011.10.005.
Reinke, T., A. J. Sadowski, T. Ummenhofer, and J. M. Rotter. 2014. “Large scale bending tests of spiral welded steel tubes.” In Proc., Eurosteel 2014. Brussels, Belgium: European Convention for Coinstructional Steelwork.
Rotter, J. M., A. J. Sadowski, and L. Chen. 2014. “Nonlinear stability of thin elastic cylinders of different length under global bending.” Int. J. Solids Struct. 51 (15–16): 2826–2839. https://doi.org/10.1016/j.ijsolstr.2014.04.002.
Sadowski, A. J., and J. M. Rotter. 2014. “Modeling and behaviour of cylindrical shell structures with helical features.” Comput. Struct. 133: 90–102. https://doi.org/10.1016/j.compstruc.2013.11.012.
Song, C. Y., J. G. Teng, and J. M. Rotter. 2004. “Imperfection sensitivity of thin elastic cylindrical shells subject to partial axial compression.” Int. J. Solids Struct. 41 (24–25): 7155–7180. https://doi.org/10.1016/j.ijsolstr.2004.05.040.
Teng, J. G., and C. Y. Song. 2001. “Numerical models for nonlinear analysis of elastic shells with eigenmode-affine imperfections.” Int. J. Solids Struct. 38 (18): 3263–3280. https://doi.org/10.1016/S0020-7683(00)00222-5.
van Es, S. H. J., A. M. Gresnigt, D. Vasilikis, and S. A. Karamanos. 2016. “Ultimate bending capacity of spiral-welded steel tubes. Part I: Experiments.” Thin-Walled Struct. 102: 286–304. https://doi.org/10.1016/j.tws.2015.11.024.
Wang, J., A. J. Sadowski, and J. M. Rotter. 2018. “Influence of ovalisation on the plastic collapse of thick cylindrical tubes under uniform bending.” Int. J. Pressure Vessels Piping 168: 94–99. https://doi.org/10.1016/j.ijpvp.2018.05.004.
Xu, Z., L. Gardner, and A. J. Sadowski. 2017. “Nonlinear stability of elastic elliptical cylindrical shells under uniform bending.” Int. J. Mech. Sci. 128–129: 593–606. https://doi.org/10.1016/j.ijmecsci.2017.05.022.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 31, 2018
Accepted: Aug 22, 2018
Published online: Jan 12, 2019
Published in print: Mar 1, 2019
Discussion open until: Jun 12, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.