Dynamics of Tire Crossing on a Gapped Road Surface
Publication: Journal of Engineering Mechanics
Volume 144, Issue 4
Abstract
The safety of cars and trucks crossing gapped road surfaces can be affected by their operational speed, mass, and the tire and road surface characteristics. As part of a research on the safety of road vehicles crossing discontinuous road surfaces, the dynamic behavior of a single tire passing a gap has been examined as reported in this paper. First, the kinematics of a tire crossing the gap in the road surface is analytically formulated. The formulation has shown that the tire exhibits three distinct (single-point, two-point, and flying) modes of travel depending on its operational speed. The dynamics of the tire are larger in single-point mode that exhibits two critical velocities, which have been validated using a nonlinear arbitrary Lagrangian Eulerian method in the finite-element framework. The validated analytical model has shown that the critical velocity is mainly affected by the mass of the overburden.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The first author acknowledges the fee waiver provided by the Queensland University of Technology (QUT) and the doctoral scholarship provided by the School of Civil Engineering & Built Environment of QUT. This work is supported by the Australian Research Council Discovery Project Grant (DP150100814).
References
ABAQUS [Computer software]. Dassault Systèmes, Waltham, MA.
Bandula-Heva, T., and Dhanasekar, M. (2014). “Failure of discontinuous railhead edges due to plastic strain accumulation.” Eng. Fail. Anal., 44, 110–124.
Bandula-Heva, T., Dhanasekar, M., and Boyd, P. (2013). “Experimental investigation of wheel/rail rolling contact at railhead edge.” Exp. Mech., 53(6), 943–957.
Baranowski, P., Malachowski, J., Janiszewski, J., and Wekezer, J. (2016a). “Detailed tyre FE modelling with multistage validation for dynamic analysis.” Mater. Des., 96, 68–79.
Baranowski, P., Malachowski, J., and Mazurkiewicz, L. (2016b). “Numerical and experimental testing of vehicle tyre under impulse loading conditions.” Int. J. Mech. Sci., 106, 346–356.
Barbani, D., Pierini, M., and Baldanzini, N. (2012). “FE modelling of a motorcycle tyre for full-scale crash simulations.” Int. J. Crashworthiness, 17(3), 309–318.
Behroozi, M., Olatunbosun, O., and Ding, W. (2012). “Finite element analysis of aircraft tyre—Effect of model complexity on tyre performance characteristics.” Mater. Des., 35, 810–819.
Billal, M. K., Carneiro, G., Ozelo, R., and Kulkarni, M. (2015). “Simulation of vehicle pothole test and techniques used.” SAE International, Warrendale, PA.
Bolarinwa, E., and Olatunbosun, O. (2004). “Finite element simulation of the tyre burst test.” Proc. Inst. Mech. Eng. Part D J. Automobile Eng., 218(11), 1251–1258.
Cai, W., Wen, Z., Jin, X., and Zhai, W. (2007). “Dynamic stress analysis of rail joint with height difference defect using finite element method.” Eng. Fail. Anal., 14(8), 1488–1499.
Cho, J., Kim, K., Jeon, D., and Yoo, W. (2005). “Transient dynamic response analysis of 3-D patterned tire rolling over cleat.” Eur. J. Mech. A. Solids, 24(3), 519–531.
Conradie, J. M., Els, P. S., and Heyns, P. S. (2016). “Finite element modelling of off-road tyres for radial tyre model parameterization.” Proc. Inst. Mech. Eng., Part D J. Automobile Eng., 230(4), 564–578.
Diaz, C. G., et al. (2016). “Dynamic behaviour of a rolling tyre: Experimental and numerical analyses.” J. Sound Vib., 364, 147–164.
Dukkipati, R. V., and Dong, R. (1999). “Impact loads due to wheel flats and shells.” Veh. Syst. Dyn., 31(1), 1–22.
Li, H., and Schindler, C. (2014). “Transient dynamics of an excavator tyre rolling over speed bump.” Proc. Inst. Mech. Eng. Part K J. Multi-Body Dyn., 228(3), 229–240.
Mandal, N. K., Dhanasekar, M., and Sun, Y. Q. (2016). “Impact forces at dipped rail joints.” Proc., Inst. Mech. Eng. Part F: J. Rail Rapid Trans., 230(1), 271–282.
Metz, L. D., and Sneddon, J. (2015). “Vehicle dynamics simulation associated with pothole encounters using the HVE SIMON program and radial spring tire model.” SAE International, Warrendale, PA.
Mousseau, C. W., and Hulbert, G. M. (1996). “An efficient tire model for the analysis of spindle forces produced by a tire impacting large obstacles.” Comput. Methods Appl. Mech. Eng., 135(1–2), 15–34.
Nackenhorst, U. (2004). “The ALE-formulation of bodies in rolling contact: Theoretical foundations and finite element approach.” Comput. Methods Appl. Mech. Eng., 193(39), 4299–4322.
Neves, R., Micheli, G., and Alves, M. (2010). “An experimental and numerical investigation on tyre impact.” Int. J. Impact Eng., 37(6), 685–693.
Pacejka, H., and Besselink, I. (1997). “Magic formula tyre model with transient properties.” Veh. Syst. Dyn., 27(S1), 234–249.
Palanivelu, S., Rao, K. V. N., and Ramarathnam, K. K. (2015). “Determination of rolling tyre modal parameters using finite element techniques and operational modal analysis.” Mech. Syst. Sig. Process., 64–65, 385–402.
Reida, J., Boesch, D., and Bielenberg, R. (2007). “Detailed tire modeling for crash applications.” Int. J. Crashworthiness, 12(5), 521–529.
Steenbergen, M. J. (2006). “Modelling of wheels and rail discontinuities in dynamic wheel-rail contact analysis.” Veh. Syst. Dyn., 44(10), 763–787.
Sun, G., Pang, T., Zheng, G., Song, J., and Li, Q. (2016). “On energy absorption of functionally graded tubes under transverse loading.” Int. J. Mech. Sci., 115–116, 465–480.
Wei, C. (2015). “A finite element based approach to characterising flexible ring tire (FTire) model for extended range of operating conditions.” Ph.D. dissertation, Univ. of Birmingham, Birmingham, U.K.
Wei, C., and Olatunbosun, O. A. (2014). “Transient dynamic behaviour of finite element tire traversing obstacles with different heights.” J. Terramech., 56, 1–16.
Wei, C., and Olatunbosun, O. A. (2016). “The effects of tyre material and structure properties on relaxation length using finite element method.” Mater. Des., 102, 14–20.
Wu, T. X., and Thompson, D. J. (2002). “A hybrid model for the noise generation due to railway wheel flats.” J. Sound Vib., 251(1), 115–139.
Zong, N., and Dhanasekar, M. (2013). “Hybrid genetic algorithm for elimination of severe stress concentration in railhead ends.” J. Comput. Civ. Eng., 04014075.
Zong, N., and Dhanasekar, M. (2014). “Experimental studies on the performance of rail joints with modified wheel/railhead contact.” Proc. Inst. Mech. Eng. Part F J. Rail Rapid Transit, 228(8), 857–877.
Zong, N., and Dhanasekar, M. (2017). “Sleeper embedded insulated rail joints for minimising the number of modes of failure.” Eng. Fail. Anal., 76, 27–43.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: May 19, 2017
Accepted: Oct 19, 2017
Published online: Feb 8, 2018
Published in print: Apr 1, 2018
Discussion open until: Jul 8, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.