Effect of Slip-Hardening Interface Behavior on Fiber Rupture and Crack Bridging in Fiber-Reinforced Cementitious Composites
Publication: Journal of Engineering Mechanics
Volume 141, Issue 10
Abstract
A generic crack bridging model for short fiber-reinforced cementitious composites is developed aiming to analytically account for fiber tensile rupture at the pullout stage and two-way fiber pullout induced by both the slip-hardening interface behavior and the chemical bond and fiber tensile rupture at the debonding stage. Explicit solutions to the current model have been given in this paper. The predicted composite bridging-stress versus crack-opening relations as well as concerned composite characteristics such as the tensile strength and mean postfailure crack opening are shown to reasonably agree with the experimental results for a series of polyvinyl alcohol fiber-based engineered cementitious composites. The influence of slip-hardening interface behavior on fiber rupture and crack bridging is clarified by comparing current model with a previous model. It is found that the slip-hardening interface behavior-induced fiber rupture can significantly govern the crack bridging behavior, and it is essential to take this effect into account. A parametric study based on the current model identifies the critical value of the slip-hardening coefficient for the optimal composite properties.
Get full access to this article
View all available purchase options and get full access to this article.
References
Kanda, T., and Li, V. C. (1998). “Interface property and apparent strength of high-strength hydrophilic fiber in cement matrix.” J. Mater. Civ. Eng., 5–13.
Kanda, T., and Li, V. C. (1999a). “Effect of fiber strength and fiber-matrix interface on crack bridging in cement composites.” J. Eng. Mech., 290–299.
Kanda, T., and Li, V. C. (1999b). “New micromechanics design theory for pseudostrain hardening cementitious composite.” J. Eng. Mech., 373–381.
Kanda, T., Lin, Z., and Li, V. C. (2000). “Tensile stress-strain modeling of pseudostrain hardening cementitious composites.” J. Mater. Civ. Eng., 147–156.
Li, V. C. (1993). “From micromechanics to structural engineering-The design of cementitous composites for civil engineering applications.” JSCE J. Struct. Mech. Earthquake Eng., 10(2), 37–48.
Li, V. C., and Leung, C. K. (1992). “Steady-state and multiple cracking of short random fiber composites.” J. Eng. Mech., 2246–2264.
Li, V. C., Mishra, D. K., and Wu, H.-C. (1995). “Matrix design for pseudo-strain-hardening fibre reinforced cementitious composites.” Mater. Struct., 28(10), 586–595.
Li, V. C., Wang, S., and Wu, C. (2001). “Tensile strain-hardening behavior of polyvinyl alcohol engineered cementitious composite (PVA-ECC).” ACI Mater. J., 98(6), 483–492.
Li, V. C., Wang, Y., and Backer, S. (1990). “Effect of inclining angle, bundling and surface treatment on synthetic fibre pull-out from a cement matrix.” Composites, 21(2), 132–140.
Li, V. C., Wang, Y., and Backer, S. (1991). “A micromechanical model of tension-softening and bridging toughening of short random fiber reinforced brittle matrix composites.” J. Mech. Phys. Solids, 39(5), 607–625.
Li, V. C., Wu, C., Wang, S., Ogawa, A., and Saito, T. (2002). “Interface tailoring for strain-hardening polyvinyl alcohol-engineered cementitious composite (PVA-ECC).” ACI Mater. J., 99(5), 463–472.
Li, V. C., and Wu, H.-C. (1992). “Conditions for pseudo strain-hardening in fiber reinforced brittle matrix composites.” J. Appl. Mech. Rev., 45(8), 390–398.
Lin, Z., Kanda, T., and Li, V. C. (1999). “On interface property characterization and performance of fiber reinforced cementitious composites.” Concr. Sci. Eng., 1(3), 173–184.
Lin, Z., and Li, V. C. (1997). “Crack bridging in fiber reinforced cementitious composites with slip-hardening interfaces.” J. Mech. Phys. Solids, 45(5), 763–787.
Maalej, M., Li, V. C., and Hashida, T. (1995). “Effect of fiber rupture on tensile properties of short fiber composites.” J. Eng. Mech., 903–913.
Marshall, D., and Cox, B. (1988). “A J-integral method for calculating steady-state matrix cracking stresses in composites.” Mech. Mater., 7(2), 127–133.
Naaman, A. (2003). “Strain hardening and deflection hardening fiber reinforced cement composites.” Proc., 4th Int. RILEM Workshop on High Performance FiberReinforced Cement Composites (HPFRCC4), RILEM Publications S.A.R.L, Ann Arbor, 95–113.
Parra-Montesinos, G. J. (2005). “High-performance fiber-reinforced cement composites: an alternative for seismic design of structures.” ACI Struct. J., 102(5), 668.
Redon, C., Li, V. C., Wu, C., Hoshiro, H., Saito, T., and Ogawa, A. (2001). “Measuring and modifying interface properties of PVA fibers in ECC matrix.” J. Mater. Civ. Eng., 399–406.
Wang, Y., Li, V., and Backer, S. (1991). “Tensile failure mechanisms in synthetic fibre-reinforced mortar.” J. Mater. Sci., 26(24), 6565–6575.
Wang, Y., Li, V. C., and Backer, S. (1988a). “Analysis of synthetic fiber pull-out from a cement matrix.” Proc., Material Research Society Symp., Cambridge Univ Press, Pittsburgh, PA, 159–165.
Wang, Y., Li, V. C., and Backer, S. (1988b). “Modelling of fibre pull-out from a cement matrix.” Int. J. Cem. Compos. Lightweight Concr., 10(3), 143–149.
Wu, H. C., and Li, V. C. (1999). “Fiber/cement interface tailoring with plasma treatment.” Cem. Concr. Compos., 21(3), 205–212.
Yang, E. H., Wang, S., Yang, Y., and Li, V. C. (2008). “Fiber-bridging constitutive law of engineered cementitious composites.” J. Adv. Concr. Technol., 6(1), 181–193.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Nov 12, 2014
Accepted: Jan 15, 2015
Published online: May 5, 2015
Published in print: Oct 1, 2015
Discussion open until: Oct 5, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.