Novel Slot-Baffle Design to Improve Mixing Efficiency and Reduce Cost of Disinfection in Drinking Water Treatment
Publication: Journal of Environmental Engineering
Volume 143, Issue 9
Abstract
In potable water treatment, the commonly used disinfectants are chlorine and ozone. Recently, the use of ozone has gained more acceptance due to its effective disinfectant properties. However, water treatment with ozone is more expensive because ozone production is an energy-intensive processes. Thus the mechanical mixing efficiency (passive mixing) of the contact system used in this process is critical to reduce the amount of disinfectant used to treat a fixed volume of water. Traditional contact tank designs suffer from poor mixing, short-circuiting, and high energy requirements to drive the flow through the contactor. This study introduces a patented novel baffle design to improve the efficiency of contact tanks. Computational fluid dynamics (CFD)–based analysis indicates that the proposed baffle design improves the mechanical mixing efficiency by 51% and reduces the energy required to drive the flow through the system and short-circuiting by 51 and 57%, respectively. Calculations indicate that the savings offered by this design will be on the order of several hundred thousand dollars per year for medium-sized water treatment plants. The proposed design is simple to implement without expensive infrastructure modifications, and can be used for both chlorine and ozone treatment.
Get full access to this article
View all available purchase options and get full access to this article.
References
Angeloudis, A., Stoesser, T., and Falconer, R. A. (2014). “Predicting the disinfection efficiency range in chlorine contact tanks through a CFD-based approach.” Water Res., 60(4), 118–129.
Angeloudis, A., Stoesser, T., Gualtieri, C., and Falconer, R. A. (2016). “Contact tank design impact on process performance.” Environ. Model. Assess., 21(5), 563–576.
Demirel, E., and Aral, M. M. (2016a). “Unified analysis of multi-chamber contact tanks and mixing efficiency based on vorticity field. Part I: Hydrodynamic analysis.” Water, 8(11), 495–516.
Demirel, E., and Aral, M. M. (2016b). “Unified analysis of multi-chamber contact tanks and mixing efficiency based on vorticity field. Part II: Transport analysis.” Water, 8(11), 537–554.
Elliot, T., Zeier, B., Xagoraraki, I., and Harrington, G. W. (2003). “Energy use at Wisconsin’s drinking water facilities.”, Energy Center of Wisconsin, Madison, WI.
EPRI (Electric Power Research Institute). (2013). “Electricity use and management in the municipal water supply and wastewater industries.”, Water Research Foundation, Palo Alto, CA.
Heathcote, G. R., and Drage, B. E. (1995). “Development of an ozone disinfection contactor using a physical scale model.” Ozone Sci. Eng., 17(1), 15–24.
Kim, D., Elovitz, M., Roberts, P. J. W., and Kim, J. H. (2010a). “Using 3D LIF to investigate and improve performance of a multi-chamber ozone contactor.” J. Am. Water Works Assoc., 102(10), 61–70.
Kim, D., Kim, D. I., Kim, J. H., and Stoesser, T. (2010b). “Large eddy simulation of flow and tracer transport in multi-chamber ozone contactor.” J. Environ. Eng., 22–31.
Kim, D., Stoesser, T., and Kim, J. H. (2013). “The effect of baffle spacing on hydrodynamics and solute transport in serpentine contact tanks.” J. Hyd. Res., 51(5), 558–568.
Langlais B., Reckhow D. A., and Brink D. R., eds. (1991). Ozone in water treatment: Application and engineering, Lewis, Chelsea, MI.
Rauen, W. B., Angeloudis, A., and Falconer, R. A. (2012). “Appraisal of chlorine contact tank modelling practices.” Water Res., 46(18), 5834–5847.
Rauen, W. B., Lin, B., Falconer, R. A., and Teixeira, E. C. (2008). “CFD and experimental model studies for water disinfection tanks with low Reynolds number flows.” Chem. Eng. J., 137(3), 550–560.
Taylor, Z. H., Carlston, J. S., and Venayagamoorthy, S. K. (2015). “Hydraulic design of baffles in disinfection contact tanks.” J. Hydraul. Res., 53(3), 400–407.
Teixeira, E. C., and Siqueira, R. N. (2008). “Performance assessment of hydraulic efficiency indexes.” J. Environ. Eng., 851–859.
USEPA (U.S. Environmental Protection Agency). (2013). “Disinfection profiling and benchmarking guidance manual. Appendix A.”, Washington, DC.
Wang, H., and Falconer, R. A. (1998). “Simulating disinfection processes in chlorine contact tanks using various turbulence models and high-order accurate difference schemes.” Water Res., 32(5), 1529–1543.
Water in the West. (2013). Water and energy nexus: A literature review, Stanford Univ., Stanford, CA, 135.
Wols, B. A., Hofman, J. A. M. H., Uijttewaal, W. S. J., Rietveld, L. C., and van Dijk, J. C. (2010). “Evaluation of different disinfection calculation methods using CFD.” Environ. Modell. Software, 25(4), 573–582.
Zhang, J., Martinez, A. E. T., Lei, H., and Zhang, Q. (2016). “Indicators for technological, environmental and economic sustainability of ozone contactors.” Water Res., 101(1), 606–616.
Zhang, J., Martinez, A. E. T., and Zhang, Q. (2013a). “Hydraulic efficiency in RANS of the flow in multi-chambered contactors.” J. Hydraul. Eng, 1150–1157.
Zhang, J., Martinez, A. E. T., and Zhang, Q. (2013b). “Reynolds-averaged Navier-Stokes simulation of the flow and tracer transport in a multi-chambered ozone contactor.” J. Environ. Eng., 450–454.
Zhang, J., Martinez, A. E. T., Zhang, Q., and Lei, H. (2014). “Evaluating hydraulic and disinfection efficiencies of a full-scale ozone contactor using a RANS-based modeling framework.” Water Res., 52(5), 155–167.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Dec 28, 2016
Accepted: Apr 19, 2017
Published online: Jul 7, 2017
Published in print: Sep 1, 2017
Discussion open until: Dec 7, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.