Survey of the Operational Status of 25 Swedish Municipal Stormwater Management Ponds
Publication: Journal of Environmental Engineering
Volume 143, Issue 6
Abstract
During the past 50 years, wet stormwater ponds have been constructed to reduce negative environmental impacts of urban stormwater discharges on receiving aquatic environments. However, in many jurisdictions there is little information on the current operational status of such ponds and their functioning. This paucity of information prompted a field survey of 25 Swedish municipal stormwater ponds, aged between 3 and 26 years. The pond survey focused on estimating the pond hydraulic loading and efficiency, the state of littoral vegetation, characteristics of bottom sediment in the inlet and outlet zones (sizes and the chemistry), and the overall operational pond status, including the access for maintenance. The hydraulic efficiencies of ponds were estimated for pond footprint shapes and relative locations of the inlets and outlets using literature data. The estimated hydraulic efficiencies correlated well with the pond length-to-width ratios and the ratio of the pond surface area to the impervious area of the runoff contributing catchment (i.e., the hydraulic loading). Littoral vegetation was inspected visually and found to be overgrown at some facilities, which impeded the maintenance access. Benthic sediments in ponds contained silt and clay (), sand and gravel fractions, and when compared with the literature data, such sediments appeared relatively coarse. Chemical characteristics of sediments reflected anthropogenic (traffic) activities, but without excessive contamination warranting special disposal requirements. Of the 25 ponds surveyed, four were fenced off and inaccessible to machinery. In fact, the design of these four ponds was such that it made inspection and maintenance very difficult, which may pose potential risks to ponds operation. Fifty-four percent of the investigated ponds were in need of minor maintenance, primarily because of sediment and litter accumulation in their inflow and outflow sections. The fact that the inspection survey revealed relatively few minor issues that could be corrected easily demonstrates the importance of relatively simple regular inspections serving to detect minor problems at an early stage before they would seriously impact pond functioning. The above survey methodology should be helpful for developing similar low-cost surveys in other jurisdictions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank the staff of Växjö, Malmö, Örebro, Umeå, and Östersund Municipalities for their assistance in providing the information needed during field sampling. This work was performed as an activity of the research cluster Dag & Nät. Financial support for this work from Norrbottens forskningsråd is gratefully acknowledged.
References
ASTM. (2007). “Standard test method for particle-size analysis of soils.” ASTM D422-63, West Conshohocken, PA.
Bardet, J. P. (1997). Experimental soil mechanics, Prentice Hall, Upper Saddle River, NJ.
Bishop, C. A., Struger, J., Barton, D. R., Shirose, L. J., Dunn, L., and Campbell, G. D. (2000). “Contamination and wildlife communities in stormwater detention ponds in Guelph and the Greater Toronto Area, Ontario, 1997 and 1998. Part II—Contamination and biological effects of contamination.” Water Qual. Res. J. Can., 35(3), 437–474.
Blecken, G. T., Hunt, W. F., Al-Rubaei, A. M, Viklander, M., and Lord, W. G. (2017). “Stormwater control measure (SCM) maintenance considerations to ensure designed functionality.” Urban Water J., 14(3), 278–290.
Blecken, G. T., Rentz, R., Malmgren, C., Öhlander, B., and Viklander, M. (2012). “Stormwater impact on urban waterways in a cold climate: Variations in sediment metal concentrations due to untreated snowmelt discharge.” J. Soils Sediments, 12(5), 758–773.
Brydon, J., Oh, I., Wilson, J., Hall, K., and Schreier, H. (2009). “Evaluation of mitigation methods to manage contaminant transfer in urban watersheds.” Water Qual. Res. J. Can., 44(1), 1–15.
Camponelli, K. M., Lev, S. M., Snodgrass, J. W., Landa, E. R., and Casey, R. E. (2010). “Chemical fractionation of Cu and Zn in stormwater, roadway dust and stormwater pond sediments.” Environ. Pollut., 158(6), 2143–2149.
Comings, K. J., Booth, D. B., and Horner, R. R. (2000). “Storm water pollutant removal by two wet ponds in Bellevue, Washington.” J. Environ. Eng., 321–330.
Crawford, K. D., Weinstein, J. E., Hemingway, R. E., Garner, T. R., and Globensky, G. (2010). “A survey of metal and pesticide levels in stormwater retention pond sediments in coastal South Carolina.” Arch. Environ. Contam. Toxicol., 58(1), 9–23.
D’Arcy, B. J., and Sieker, H. (2015). Germany’s long-term support for SUDS development, IWA Publishing, London, 26–28.
Datry, T., Malard, F., Vitry, L., Hervant, F., and Gibert, J. (2003). “Solute dynamics in the bed sediments of a stormwater infiltration basin.” J. Hydrol., 273(1), 217–233.
Egemose, S., Sønderup, M. J., Grudinina, A., Hansen, A. S., and Flindt, M. R. (2015). “Heavy metal composition in stormwater and retention in ponds dependent on pond age, design and catchment type.” Environ. Technol., 36(8), 959–969.
Ellis, J. B., and Marsalek, J. (1996). “Overview of urban drainage: environmental impacts and concerns, means of mitigation and implementation policies.” J. Hydraul. Res., 34(6), 723–732.
Fletcher, T. D., et al. (2015). “SUDS, LID, BMPs, WSUD and more—The evolution and application of terminology surrounding urban drainage.” Urban Water J., 12(7), 525–542.
Frost, P. C., Song, K., Buttle, J. M., Marsalek, J., McDonald, A., and Xenopoulos, M. A. (2015). “Urban biogeochemistry of trace elements: What can the sediments of stormwater management ponds tell us?” Urban Ecosyst., 18(3), 763.
Guo, Y., and Adams, B. J. (1994). “Long term performance modelling of stormwater quality ponds.” Current practices in modelling the management of stormwater impacts, W. James, ed., Lewis Publishers, Boca Raton, FL, 99–119.
Heal, K. V., Hepburn, D. A., and Lunn, R. J. (2006). “Sediment management in sustainable urban drainage system ponds.” Water Sci. Technol., 53(10), 219–227.
Herricks, E. (1995). Stormwater runoff and receiving systems: Impact, monitoring, and assessment, CRC Press, Boca Raton, FL.
Hunt, W. F., et al. (2011). “Constructed storm-water wetland installation and maintenance: Are we getting it right?” J. Irrig. Drain. Eng., 469–474.
Hunt, W. F., and Lord, W. G (2006). “Maintenance of stormwater wetlands and wet ponds.”, North Carolina Cooperative Extension Service, Urban Water Ways Series, Raleigh, NC.
Hvitved-Jacobsen, T., Johansen, N. B., and Yousef, Y. A. (1994). “Treatment systems for urban and highway run-off in Denmark.” Sci. Total Environ., 146, 499–506.
ISO. (2000). “Test sieves—Technical requirements and testing—Part 1: Test sieves of metal wire cloth.” ISO 3310-1, Geneva.
Istenič, D., et al. (2012). “Improved urban stormwater treatment and pollutant removal pathways in amended wet detention ponds.” J. Environ. Sci. Health., Part A, 47(10), 1466–1477.
Jansons, K., and Law, S. (2007). “The hydraulic efficiency of simple stormwater ponds.” Rainwater and urban design, Engineers Australia, Barton, ACT, Australia, 452–459.
Karlsson, K., Viklander, M., Scholes, L., and Revitt, M. (2010). “Heavy metal concentrations and toxicity in water and sediment from stormwater ponds and sedimentation tanks.” J. Hazard. Mater., 178(1), 612–618.
Larm, T. (2000). “Utformning och dimensionering av dagvattenreningsanläggningar [Design and dimensioning of stormwater treatment facilities].”, Stockholm, Sweden (in Swedish).
Levene, H. (1960). “Robust tests for equality of variances1.” Contributions to probability and statistics: Essays in honor of Harold Hotelling, I. Olkin, ed., Stanford University Press, Palo Alto, CA, 278–292.
Marsalek, J., and Marsalek, P. M. (1997). “Characteristics of sediments from a stormwater management pond.” Water Sci. Technol., 36(8), 117–122.
Marsalek, J., Urbonas, B., and Lawrence, I. (2005). Stormwater Management Ponds, Pond Treatment Technology, A. Shilton, ed., IWA Publishing, London, 432–459.
Marsalek, J., Watt, W. E., Anderson, B. C., and Jaskot, C. (1997). “Physical and chemical characteristics of sediments from a stormwater management pond.” Water Qual. Res. J. Can., 32(1), 89–100.
Matthews, R. R., Watt, W. E., Marsalek, J., Crowder, A. A., and Anderson, B. C. (1997). “Extending retention times in a stormwater pond with retrofitted baffles.” Water Qual. Res. J. Can., 32(1), 73–87.
McNett, J. K., and Hunt, W. F. (2011). “An evaluation of the toxicity of accumulated sediments in forebays of stormwater wetlands and wet ponds.” Water Air Soil Pollut., 218(1–4), 529–538.
Minitab version 17 [Computer software]. Minitab, Inc., State College, PA.
Moreton Bay Waterways and Catchment. (2006). “Water sensitive urban design: Technical design guidelines for south east Queensland.” Moreton Bay waterways and catchment partnership, Brisbane, QLD, Australia.
Nix, S. J. (1985). “Residence time in stormwater detention basins.” J. Environ. Eng., 95–100.
Persson, J. (2000). “The hydraulic performance of ponds of various layouts.” Urban Water, 2(3), 243–250.
Persson, J., Somes, N. L. G., and Wong, T. H. F. (1999). “Hydraulics efficiency of constructed wetlands and ponds.” Water Sci. Technol., 40(3), 291–300.
Pettersson, T. J., German, J., and Svensson, G. (1999). “Pollutant removal efficiency in two stormwater ponds in Sweden.” Proc., 8th Int. Conf. on Urban Storm Drainage, IWA Publishing, London, 866–873.
Putnam, G., Doll, B., and Winston, R. (2013). “Stormwater ponds: Improving aesthetics, value and function.”, North Carolina Sea Grant, Sustainability series, Chapel Hill, NC.
Sansalone, J. J., and Buchberger, S. G. (1997). “Characterization of solid and metal element distributions in urban highway stormwater.” Water Sci. Technol., 36(8), 155–160.
Schueler, T. R. (1987). Controlling urban runoff: A practical manual for planning and designing urban BMPs, Metropolitan Washington Council of Governments, Washington, DC.
Shaw, J. K. E., Watt, W. E., Marsalek, J., Anderson, B. C., and Crowder, A. A. (1997). “Flow pattern characterization in an urban stormwater detention pond and implications for water quality.” Water Qual. Res. J. Can., 32(1), 53–71.
Song, K., et al. (2013). “Thermal stratification patterns in urban ponds and their relationships with vertical nutrient gradients.” J. Environ. Manage., 127, 317–323.
SSI (Swedish Standards Institute). (2006). “Water quality—Application of inductively coupled plasma mass spectrometry (ICP-MS)—Part 1: General guidelines.”. Swedish Standards Institute, Stockholm, Sweden.
Starzec, P., Lind, B. B., Lanngren, A., Lindgren, Å., and Svenson, T. (2005). “Technical and environmental functioning of detention ponds for the treatment of highway and road runoff.” Water Air Soil Pollut., 163(1–4), 153–167.
Swedish EPA (Swedish Environmental Protection Agency). (2000). “Environmental quality criteria—Lakes and watercourses.”, Stockholm, Sweden.
Swedish EPA (Swedish Environmental Protection Agency). (2009). “Riktvärden för förorenad mark—Modellbeskrivning och vägledning [Guideline values for contaminated land. Model description and guidance].”, Stockholm, Sweden (in Swedish).
USEPA (U.S. Environmental Protection Agency). (1994). “Determination of trace elements in waters and wastes by inductively coupled plasma-mass spectrometry.”, Washington, DC.
USEPA (U.S. Environmental Protection Agency). (1983). “Results of the nationwide urban runoff program.”, Water Planning Division, Washington, DC.
USEPA (U.S. Environmental Protection Agency). (1999). “Storm water technology fact sheet: Wet detention ponds.”, Office of Water, Washington, DC.
VanLoon, G., Anderson, B. C., Watt, W. E., and Marsalek, J. (2000). “Characterizing stormwater sediments for ecotoxic risk.” Water Qual. Res. J. Can., 35(3), 341–364.
Venner, M., Marc, L., Dan, P., and Eric, S. (2004). “Identification of research needs related to highway runoff management.”, Transportation Research Board, Washington, DC.
Viklander, M. (1998). “Particle size distribution and metal content in street sediments.” J. Environ. Eng., 761–766.
Walsh, C. J. (2000). “Urban impacts on the ecology of receiving waters: A framework for assessment, conservation and restoration.” Hydrobiologia, 431(2), 107–114.
Yousef, Y. A., Hvitved-Jacobsen, T., Harper, H. H., and Lin, L. Y. (1990). “Heavy metal accumulation and transport through detention ponds receiving highway runoff.” Sci. Total Environ., 93, 433–440.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Mar 28, 2016
Accepted: Nov 7, 2016
Published ahead of print: Feb 10, 2017
Published online: Feb 11, 2017
Published in print: Jun 1, 2017
Discussion open until: Jul 11, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.